What is the fuel consumption of the Volkswagen Viloran?

1 Answers
SanJake
07/30/25 10:47am
The combined fuel consumption of the Volkswagen Viloran is 7.6-8.1L/100km. Currently, there are 4 models of the Volkswagen Viloran on sale: the Luxury version and the Business version, with a combined fuel consumption of 7.6L/100km, and the Premium version and the Flagship version, with a combined fuel consumption of 8.1L/100km. The above figures are the NEDC combined fuel consumption, which is the data measured under the NEDC test procedure for combined driving conditions. The actual fuel consumption is higher than these values, ranging from 7.6-12L/100km. The level of a car's fuel consumption is directly related to five major factors: driving habits, the car itself, road conditions, natural wind, and environmental temperature. Specific factors that can increase fuel consumption are as follows: Driving habits: Aggressive driving, such as sudden acceleration, frequent overtaking, and not easing off the throttle before reaching a red light, can increase fuel consumption. The car itself: Cars with larger engine displacements generally consume more fuel than those with smaller displacements because larger displacements usually mean greater power, requiring more gasoline to burn and perform work. Heavier cars also consume more fuel because greater weight requires more driving torque. Road conditions: Driving on dirt roads, muddy roads, soft surfaces, or mountainous roads increases resistance and fuel consumption. Natural wind: Driving against the wind or on windy days increases the car's resistance and fuel consumption. Low environmental temperatures: When the engine block temperature is low, the gasoline injected during a cold start does not atomize easily, requiring more gasoline to be injected for combustion, which increases fuel consumption. Additionally, at low temperatures, the engine's computer will control the engine to run at higher RPMs to warm up, which also increases fuel consumption.
Was this review help?
1
2
Share
More Forum Discussions

Can You Still Drive When the Engine Malfunction Indicator Light Is On?

When the engine malfunction indicator light comes on, it can be divided into the following two situations: 1. First, if the engine malfunction light is on, but the driver does not feel any difference while driving, and basic operations such as acceleration and deceleration can be performed normally, then the car can still continue to be driven. This situation is usually caused by a faulty sensor in the car, which does not affect the driving of the car, at most the emissions may become slightly higher, and sometimes the light may even turn off by itself. However, it should not be ignored, and it is still necessary to have it checked when possible. 2. The second situation is when the car shows abnormalities. For example, after the engine malfunction light comes on, the car feels powerless during acceleration, or the car's vibration increases. In this case, it is not recommended for the driver to continue driving. It is best to call for assistance and have the car towed for repairs as soon as possible. Because such faults are generally more serious, continuing to drive poses a high risk.
3
5
Share

What are the reasons for engine oil deterioration?

Engine oil deterioration occurs due to the following reasons: 1. Air filter damage. The function of the air filter is to filter impurities from the air entering the engine, thereby purifying the air. Generally, a standard car has only one air filter, while luxury cars may have two. The air filter is located inside the air filter box in the engine compartment. To access the air filter, the air filter box must be opened, and it is secured either with clips or screws, both methods ensuring the box is sealed properly. 2. Oil dilution and emulsification due to water. Water can enter the cylinder block or crankcase due to a damaged cylinder head gasket or other reasons. When the water content exceeds 0.1%, the antioxidants and dispersants added to the oil become ineffective, accelerating the oxidation process of the oil. When the oil contains a significant amount of water, its lubricating properties deteriorate, viscosity decreases, and the oil film's anti-friction effect weakens. In mild cases, this leads to premature oil deterioration and rusting of components, while severe cases can cause engine seizure or bearing failure, leading to serious mechanical accidents.
20
4
Share

Can I Change the Coolant Myself?

You can change the coolant yourself. The specific steps are as follows: 1. First, drain the original coolant completely. Locate the drain valve of the car's cooling system, usually at the bottom of the car. Open the expansion tank cap, lift the car, and unscrew the drain plug to drain all the coolant. 2. After draining the coolant, fill the radiator and cooling system with clean water to flush out any remaining residue until clear water flows out from the drain. 3. Tighten the drain plug and pour the new coolant into the expansion tank, filling it to a level between the MAX and MIN marks. 4. Close the tank cap, start the car, and the coolant level in the tank will gradually drop. At this point, you need to add more coolant again, still maintaining the level between the MAX and MIN marks.
14
5
Share

What are the symptoms of a faulty car temperature sensor?

Here are the symptoms of a faulty car temperature sensor: 1. The engine may overheat, and a yellow coolant temperature warning light will appear on the dashboard to alert the driver for inspection. When the car temperature sensor is damaged, it must be repaired promptly to prevent potential safety hazards during vehicle operation. 2. The car may experience difficulty starting when cold, as the system incorrectly determines that the engine oil and coolant temperatures are too low, preventing normal operation and making the engine hard to start. The car temperature sensor controls the temperature of the engine oil and coolant, thereby helping the engine run more efficiently.
2
5
Share

Does Transmission Fluid Need to Be Changed?

Transmission fluid does need to be changed. Here are the relevant details about transmission fluid replacement: 1. Dry dual-clutch transmissions and manual transmissions have similar structures, so they both use synthetic transmission fluid with a service life of approximately 150,000 kilometers. Most automatic transmissions require fluid replacement every 60,000-80,000 kilometers. 2. The transmission fluid replacement interval is only a general guideline. Due to factors such as driving conditions and habits, the condition of the transmission fluid may vary. If the vehicle experiences symptoms like rough shifting, strong jerking sensations, or significantly increased noise during operation, it's necessary to check whether the transmission fluid needs replacement. 3. There are three common methods for changing transmission fluid: (1) Gravity drain: Similar to engine oil changes, this involves loosening the transmission drain plug to release the fluid, then refilling through the fill port. The drawback is that gravity draining doesn't completely remove all old fluid. (2) Machine flush: A transmission flush machine connects to the transmission's fluid lines, using new fluid to push out the old fluid from inside the transmission. The advantage is more thorough replacement, while the disadvantages include being time-consuming and requiring more transmission fluid. (3) Removing the transmission pan: The advantage is the ability to clean or directly replace the transmission filter, with relatively thorough fluid replacement. The drawback is the more complicated installation process.
18
0
Share

What does 91h on a tire mean?

Tire 91h indicates that the maximum load capacity of a single tire is 615Kg, and the maximum speed it can withstand under the specified load is 210KM/h. Here are the relevant details: 1. 91 is called the load index, and the maximum load capacity of 615Kg can be determined by referring to the tire load index chart. 2. H is called the speed rating. Additional information: Whether it's the speed rating or the load index, during daily driving, you should operate within the specified limits of the speed rating or load index. Otherwise, there could be significant safety hazards. Additionally, when replacing tires, it's important to note that you should not mix tires of different types, models, or tire structures.
8
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.