What is the fuel consumption of the Trumpchi GS3?

1 Answers
SanNadia
07/30/25 10:28am
According to feedback from car owners, the actual fuel consumption of the Trumpchi GS3 is around 8.2L/km. Due to differences in driving habits and road conditions, fuel consumption may vary. Here is an introduction to the Trumpchi GS3: 1. Design Style: The design of this car is relatively youthful, targeting mainly young consumers. The exterior of the car still adopts the family-style design, featuring the family-style Lingyun Wing front grille. It is also decorated with thick chrome trim, and the front headlights are connected to the grille, further highlighting the car's fashionable appeal. 2. Body Dimensions: The car's length, width, and height are 4350mm*1825mm*1655mm, with a wheelbase of 2560mm. 3. Interior: The Trumpchi GS3 does not follow the interior design style of the GS4 but adopts a brand-new design approach. The car's dashboard features rounded corners and is wrapped in large areas of soft materials, giving the interior a more welcoming look. 4. Powertrain: This car offers two powertrain options, equipped with a 1.5L naturally aspirated engine and a 1.5T turbocharged engine, paired with a 5-speed manual transmission, a 6-speed automatic manual transmission, and a 7-speed dual-clutch transmission.
Was this review help?
11
1
Share
More Forum Discussions

How to Properly Install a Motorcycle Carburetor?

First, thread the throttle cable through the carburetor top cover. Then, slide the spring onto the throttle cable. Next, pass the throttle cable through the throttle valve hole and pull it out from the adjacent slot, winding it all the way to the bottom. Finally, place the throttle cable head into the groove at the bottom of the throttle valve.
19
3
Share

How to Adjust the Air-Fuel Mixture Ratio of a Motorcycle?

Turning the mixture screw clockwise enriches the air-fuel mixture, typically by screwing it all the way in and then backing it out one and a half turns. Then, adjust the mixture screw left or right until the idle speed reaches its highest point. After that, fine-tune the idle speed to stabilize it.
5
1
Share

How to Check the Tire Wear Indicator Triangle?

To check the tire wear indicator triangle: 1. Locate the small triangular arrow mark on the side tread pattern of the tire; 2. Follow the mark to find the raised indicator in the groove of the tire tread; 3. When the tread depth is lower than the wear indicator, it means the tire is nearing the end of its life. Tire maintenance methods: 1. Ensure correct tire pressure; 2. Regularly check for bulges, cracks, cuts, punctures, or abnormal wear; 3. Inspect the tire surface for stones, nails, or other hard objects and clean them promptly; 4. Perform tire rotation. Tire rotation methods: 1. For bias-ply tires, swap the tires on the same axle to ensure even wear on both sides; 2. For radial tires, rotate them within the same side of the vehicle.
10
1
Share

What to Do When a Motorcycle Carburetor Leaks Fuel?

Pull out the float pin and remove the float and the triangular fuel needle. Insert a new all-metal triangular fuel needle of the same model into the needle valve seat. Use a small tool like a wrench to gently tap the tail end of the triangular fuel needle, creating an impact force on the needle valve seat.
16
5
Share

Is Replacing the Handbrake Cable Quick?

Replacing the handbrake cable is quick. The handbrake cable is a component found in cars equipped with mechanical handbrakes. The mechanical handbrake has a handbrake lever behind the gear shift, and this lever is connected to the cable. Symptoms of a handbrake cable not retracting: Pull the handbrake and then release it to see if the wheels turn freely. If they don't, it indicates that the cable is not retracting. Brake system: The brake system consists of a master cylinder and wheel cylinders. Simply put, the master cylinder stores brake fluid and has inlet and outlet ports. When the brake pedal is pressed, the brake fluid in the master cylinder flows through the pipes to the wheel cylinders. When the wheel cylinders are pressurized, they push the brake pads against the brake drums, achieving braking.
18
3
Share

How to Adjust the Carburetor Mixture Ratio?

Turn the carburetor mixture screw clockwise until it bottoms out, then turn it counterclockwise 1.5 turns. Let the engine warm up for 10 minutes to reach normal operating temperature. Adjust the carburetor's idle adjustment screw so that the engine runs at the lowest possible RPM without stalling. Repeatedly adjust the carburetor mixture screw left and right to achieve the highest engine RPM. Ensure the engine idles smoothly.
14
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.