What is the fuel consumption of the Toyota Reiz?

1 Answers
MaryDella
07/29/25 7:56pm
Toyota Reiz has a total of 7 models on sale, including the 2021 2.0L CVT Front-Wheel Drive Urban Edition, 2021 2.0L CVT Front-Wheel Drive Fashion Edition, and other 7 models equipped with a 193 horsepower engine, with an NEDC fuel consumption of 9L per 100 kilometers. The fuel tank capacity of different Reiz models varies, and the distance that can be covered with a full tank of fuel is as follows: Models equipped with a 193 horsepower engine have a fuel tank capacity of 70L, and the distance that can be covered with a full tank of fuel is 70/9*100=778KM. The level of a car's fuel consumption is directly related to five major factors: driving habits, the car itself, road conditions, natural wind, and environmental temperature. Specific factors that can increase a car's fuel consumption are as follows: Driving habits: Aggressive driving, such as sudden acceleration, frequent overtaking, and not easing off the throttle before reaching a red light, can increase fuel consumption. The car itself: Cars with larger displacement generally consume more fuel than those with smaller displacement because larger displacement usually means greater power, requiring more gasoline to burn and perform work. Cars with greater weight also have higher fuel consumption because greater weight requires more driving torque. Road conditions: Driving on dirt roads, muddy roads, soft surfaces, or mountainous roads increases resistance and fuel consumption. Natural wind: Driving against the wind or on windy days increases the car's resistance and fuel consumption. Low environmental temperature: When the engine block temperature is low during a cold start, the injected gasoline is less likely to vaporize, requiring more gasoline to be injected for combustion, thus increasing fuel consumption. Additionally, at low temperatures, the engine's computer may control the engine to run at higher RPMs to warm up, which also increases fuel consumption.
Was this review help?
4
4
Share
More Forum Discussions

How often should the brake pads on a Lavida be replaced?

The brake pads on a Lavida can typically last for over 30,000 kilometers, and there is no fixed replacement interval. The original brake pads for the Volkswagen Lavida are from the Bosch brand, with the front brake pads using the model number 0986AB1185 and the rear brake pads using 0986AB1178. The Lavida's rear wheels are equipped with an electronic parking system, meaning the brake calipers can only be retracted using the vehicle's onboard computer before the brake pads can be replaced. For the front wheels, tools can be used directly to reset the calipers without needing computer settings. The Lavida comes in both sedan and hatchback versions. The sedan version measures 4670 mm in length, 1806 mm in width, and 1474 mm in height, with a wheelbase of 2688 mm. The hatchback version measures 4541 mm in length, 1806 mm in width, and 1488 mm in height, also with a wheelbase of 2688 mm.
12
0
Share

Why Does the Brake Make a Clicking Sound?

Reasons for the clicking sound from the brakes: 1. When the ABS is working, it keeps the vehicle in a critical state between locking and rolling. A clicking sound occurs when the ABS is activated by hard braking, which is normal. In this case, press the brake pedal firmly to the end. 2. In automatic transmission vehicles, a clicking sound when braking may be due to the electronic linkage between the brake system and the automatic transmission. The brake is a mechanical device that slows down the vehicle, also known as a decelerator. The car's brake pedal is located under the steering wheel. Pressing the brake pedal activates the brake lever, which transmits pressure to the brake pads on the brake drum, clamping the brake disc to slow down or stop the vehicle.
13
2
Share

What is the reason for a motorcycle revving but not moving?

The reason for a motorcycle revving but not moving is: the carburetor is too dirty and needs cleaning, check the air filter, and then check the gasoline, as there may be water in the gasoline. A motorcycle consists of an engine, transmission system, running system, braking system, and electrical instrumentation equipment. The transmission system of a motorcycle is composed of primary reduction, clutch, gearbox, and secondary reduction. The solutions for a motorcycle that is difficult to start are: 1. Check the carburetor, fuel mixture ratio, oil level, and choke; 2. Check if the valve clearance is too small or if there is air leakage; 3. Check if the high-voltage spark for ignition is strong; 4. Open the choke to force start.
1
1
Share

Where is the OBD interface of the Ouliv?

The OBD interface of the Ouliv is located below the left side of the steering wheel. OBD refers to the On-Board Diagnostics system in the vehicle, and the interface below the left side of the steering wheel serves as the bridge connecting the computer to the vehicle's diagnostic system. Through this interface, using professional diagnostic tools and specific procedures, fault codes can be read from the PCM. Based on the fault codes, maintenance personnel can quickly and accurately determine the nature and location of the fault for timely repairs. The main function of the On-Board Diagnostics system is to monitor the operating conditions of the engine, as well as the status of vehicle exhaust emissions. As long as the engine is running, the vehicle will produce exhaust. Once the On-Board Diagnostics system detects a situation that may lead to excessive emissions, it will immediately issue an alarm to alert the driver. The body dimensions of the Ouliv are 3995mm in length, 1735mm in width, and 1710mm in height, with a wheelbase of 2505mm.
17
2
Share

Is it normal to have oil inside the exhaust valve?

It is abnormal to have oil inside the exhaust valve, which may be caused by aging of the crankcase ventilation valve or faults in the piston, cylinder liner, piston pin, and piston rings, resulting in loss of their original sealing effect and leading to oil spraying. The reasons for oil in the exhaust pipe may include severe wear between the valve stem and valve guide, creating excessive clearance and causing oil to leak downward. The exhaust valve, also known as the oil separator or pressure control valve, is installed between the compressor outlet and the condenser inlet. Through separation, it improves the heat transfer effect in the condenser and evaporator. The working principle of the exhaust valve: High-pressure gas (gaseous working medium and lubricating oil) from the compressor enters the exhaust valve and then the guide vanes of the exhaust valve, flowing in a spiral pattern along the vanes. By centrifugal force and gravity, the lubricating oil is separated from the working medium gas and flows down along the inner wall of the cylinder. The working medium gas is led out of the exhaust valve through a multi-hole baffle via the central pipe. The separated lubricating oil accumulates in the lower part of the oil separator and can be periodically discharged or automatically returned to the compressor's crankcase using a float valve.
19
5
Share

Is the Jiangling Ford Lingyu purely domestically produced?

Jiangling Ford Lingyu is not purely domestically produced; this vehicle is a joint venture model, a collaboration between Jiangling and the American Ford. Taking the Lingyu 2021 EcoBoost225 Jingling 5-seater model as an example, its dimensions are 4905mm in length, 1930mm in width, and 1755mm in height, with a wheelbase of 2865mm, and it features a 5-door, 5-seater SUV body structure. In terms of power, it is equipped with a 2.0-liter turbocharged engine, delivering a maximum power of 165 kW and a maximum torque of 360 Nm. For the suspension system, this model uses a MacPherson strut independent suspension at the front and a multi-link independent suspension at the rear.
20
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.