···
Log in / Register

What is the fuel consumption of the Toyota Camry 2.0?

3 Answers
StLeila
08/31/25 2:17am
The fuel consumption of the Toyota Camry 2.0 is 6.0-7.5L/100km. The currently available Camry 2.0 models include the 2021 2.0E Elite Edition, 2.0G Luxury Edition, and 2.0S Sport Edition. The official NEDC combined fuel consumption is slightly lower than real-world consumption, at 5.5-5.8L/100km. Among comparable models, the Accord's NEDC combined fuel consumption is 4.2-6.5L/100km, the Passat's is 5.8-6.7L/100km, the Teana's is 5.9-6.7L/100km, the Magotan's is 5.8-6.6L/100km, and the BMW 3 Series' is 6.1-6.9L/100km. Vehicle fuel consumption is directly influenced by five major factors: driving habits, the vehicle itself, road conditions, natural wind, and ambient temperature. Details are as follows: Driving habits: Aggressive driving behaviors such as sudden acceleration, frequent overtaking, and not easing off the throttle before red lights increase fuel consumption. The vehicle itself: Vehicles with larger displacements generally consume more fuel than those with smaller displacements because greater displacement typically means higher power output, requiring more gasoline for combustion. Heavier vehicles also have higher fuel consumption due to the greater driving torque needed. Road conditions: Driving on dirt roads, muddy roads, soft surfaces, or mountainous roads increases resistance and fuel consumption. Natural wind: Headwinds or driving on windy days increase vehicle resistance and fuel consumption. Low ambient temperatures: When the engine block is cold, injected gasoline doesn't atomize easily during cold starts, requiring more gasoline for combustion and increasing fuel consumption. Additionally, at lower temperatures, the engine's computer controls higher idle speeds to warm up the engine, which also increases fuel consumption.
Was this review help?
19
5
Share
OEden
09/12/25 5:53am
As a former owner of a Toyota Camry 2.0, I'd like to share some fuel consumption insights. This car delivers stable performance with an average fuel consumption ranging between 7.5 to 8.5 liters per 100 km, depending on driving habits. During highway cruising at steady speeds, it can drop to 6.5 liters or even lower, making it quite economical. However, in congested urban traffic, consumption often spikes above 9 liters – frequent traffic lights significantly increase fuel usage. I've observed that driving style is crucial: aggressive acceleration or hard braking can increase fuel consumption by over 10%, so smooth throttle control is essential. Don't overlook tire pressure either; I maintain 2.3 bar with weekly checks, which helps save fuel. Air conditioning also has notable impact – in summer, I first ventilate through open windows before activating AC for better energy efficiency. Regular maintenance is another key factor; changing engine oil every 5,000 km ensures proper lubrication and stable fuel economy. Overall, this model is relatively fuel-efficient among its peers, though environmental factors and personal driving style significantly influence results. For new owners, I recommend installing a fuel tracking app to monitor variations and gradually optimize driving techniques through data-driven adjustments.
Was this review help?
9
0
Share
Expand All
GageLynn
10/26/25 6:41am
I just bought a Toyota Camry 2.0 and always pay attention to the fuel consumption data while driving. The official data shows an average of 7.8 liters per 100 kilometers, which is pretty close to my actual driving experience. On highways, it can drop to as low as 6.5 liters, but during city commuting, it often exceeds 8 liters. It’s much more fuel-efficient than my friend’s older car, saving me hundreds of dollars on gas each month. I usually drive in ECO mode, which adjusts the throttle response to be smoother, reducing unnecessary acceleration. On rainy or slippery days, fuel consumption increases slightly, so I plan my route in advance to avoid congested areas. Temperature also has a noticeable impact—warming up the engine in cold winter requires a bit more fuel, but it normalizes after driving for a while. Low tire pressure increases fuel consumption, so I inflate them monthly to maintain safe pressure. My daily commute is 40 kilometers round trip, with fuel consumption fluctuating between 7.5 and 8 liters. It feels like great value for money and is perfect for daily use. If you want to save even more, try switching to synthetic oil—it makes the engine run smoother and can slightly reduce fuel consumption.
Was this review help?
18
4
Share
Expand All
More Forum Discussions

Why doesn't the automatic transmission move when shifted to D gear and accelerating?

The reasons why an automatic transmission doesn't move when shifted to D gear and accelerating are as follows: 1. Insufficient transmission fluid. 2. Low internal oil pressure. 3. Incorrect gear switch signal. 4. Issues with the shift solenoid wiring or the solenoid itself. 5. Problems with the internal transmission actuators. Here is some extended information about automatic transmission gears: 1. P gear is the parking gear, used for long-term parking of the vehicle. 2. R gear is the reverse gear, engaged when the vehicle needs to move backward. 3. N gear is the neutral gear, engaged when the vehicle is parked for a short time without turning off the engine. 4. D gear is the drive gear; when the gear lever is in D gear, the vehicle automatically shifts gears based on throttle opening and speed data. 5. S gear is the sport mode, making the vehicle drive more sportily. 6. M gear refers to manual mode; when the gear lever is in M gear, shifting is done manually by the driver. 7. L gear is the low gear.
19
3
Share

What does 45TFSI mean for the Audi A6L?

TFSI stands for Turbo Fuel Stratified Injection technology. Here is some relevant information: 1. The earliest Audi models would have labels such as 1.8TFSI, 2.0TFSI, or 3.0TFSI on the right side of the trunk to indicate the engine displacement. Later, to differentiate engine power and acceleration, the displacement labels were changed to G-values, such as 30TFSI, 35TFSI, 40TFSI, 45TFSI, and 50TFSI. 2. The G-value is calculated as the average acceleration (a) for achieving 0-100 km/h multiplied by 10. Taking the new Audi 3.0TFSI and 2.0T high-power engines as examples, the 0-100 km/h acceleration time is 6.2 seconds. The average acceleration is calculated as a = v/t = (100,000/3,600)/6.2 = 4.48. Using the formula, the G-value = 4.48 * 10 = 44.8, rounded to the nearest whole number, 45. Therefore, the new tail badge for the Audi 3.0TFSI and 2.0TFSI high-power engines is 45TFSI, no longer using displacement-based labels.
3
0
Share

What is the tutorial for replacing the ignition switch lock cylinder?

Replacing the ignition switch lock cylinder tutorial is as follows: 1. Remove the plastic cover: Remove a total of 5 cross screws underneath. 2. Remove the ignition switch: Use a hex screwdriver for removal. The screw holes can be seen above the light lever and wiper lever, with one on each side. 3. Disconnect the ignition switch plug: There is a clip on the plug, make sure to release it first. 4. Remove the lock cylinder: Turn the key to the "B" position, pull out the lock cylinder, and replace it with the new switch. Here is some additional information about the ignition switch: 1. Ignition switch: The switch of the ignition system (usually requiring a key), which can freely open or close the main circuit of the ignition coil, and is also applicable to other circuits. 2. The ignition switch is commonly known as the master switch, main power switch, or master key. It is the main gate that controls the entire vehicle's circuit system, and it comes in two types: plug-in and rotary.
12
3
Share

How to Shift into Reverse Gear in an Automatic Transmission?

To shift into reverse gear in an automatic transmission, follow these steps: 1. Press the brake pedal to bring the vehicle to a complete stop, then press the lock button on the gear lever and shift to the R (Reverse) position. 2. Check the side mirrors and rearview camera to ensure there are no obstacles behind the vehicle. Additionally, honk the horn twice to alert nearby pedestrians and vehicles. 3. Gradually release the brake pedal (or lightly press the accelerator) to allow the vehicle to move at a low speed. Here is some additional information about automatic transmissions: 1. Automatic transmission vehicles typically use a hydraulic transmission device instead of the mechanical clutch found in manual transmission vehicles, so there is no clutch pedal. 2. When the engine speed is low, the torque transmitted by the fluid is limited and insufficient to propel the vehicle forward. 3. When the gear selector is placed in the drive position and the brake pedal is released, increasing the throttle and engine speed will raise the transmitted torque, enabling the vehicle to move forward.
6
2
Share

How to Determine if the Charcoal Canister is Clogged?

When the charcoal canister is clogged, the car will emit a strong gasoline odor. If the car has been parked outdoors for an extended period, opening the fuel tank cap will result in a large amount of gas spraying out, indicating that the charcoal canister is clogged. Here are some details about charcoal canister clogging: 1. Due to high summer temperatures, a clogged charcoal canister can cause the fuel vapor in the tank to expand. Normally, excess gas is expelled from the vehicle, but when the canister is clogged, the gas cannot be released in time, accumulating in the fuel tank or fuel lines, leading to issues like vapor lock. 2. Problems with the charcoal canister can affect the car's ignition. A clogged canister does not interfere with the operation of the canister purge valve, and simply cleaning the canister may suffice. When the canister is clogged, the pipe connecting it to the fuel tank gets blocked, causing the tank to bulge, which can disrupt the engine's normal operation. 3. To prevent charcoal canister clogging, avoid overfilling the fuel tank when refueling, and never fill it up to the tank opening. If the canister is already clogged, it should be cleaned promptly at a 4S shop. If necessary, replacing the canister may be required to ensure the car's normal operation.
18
5
Share

What to Do If You Drive Without Releasing the Handbrake?

As a novice driver, driving with the handbrake on is not uncommon. Once you realize you've forgotten to release the handbrake while driving, it can be quite frightening. However, there's no need to panic—just remember to release the handbrake before starting the car in the future. Here are some suggestions: 1. Don't stress about it: This situation is quite normal, especially among new drivers. After successfully starting the car, if you notice significantly increased resistance and a slight vibration, simply check the handbrake to resolve the issue. 2. Follow the correct sequence when starting the car: The correct starting sequence is: shift to neutral, press the clutch, start the engine, release the handbrake, lift the clutch, gently apply the accelerator, and smoothly start the car. If this happens repeatedly, try to memorize the steps. 3. Short-distance driving with the handbrake on has minimal impact: Driving a few kilometers with the handbrake on is not a problem, especially since new drivers tend to drive at lower speeds. However, if you drive long distances with the handbrake on, the vehicle might start smoking. In such cases, promptly cool down the brake pads to reduce wear and tear. Additionally, get the vehicle inspected as soon as possible and replace the brake pads if necessary.
11
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.