What is the fuel consumption of the Tiggo 8 1.6t?

What Causes the Engine Warning Light to Illuminate in the Captiva?

There are primarily 7 reasons why the engine warning light illuminates in the Captiva: Sensor Malfunction: The sensors in question include those for coolant temperature, crankshaft position, air flow, intake air temperature, and oxygen sensors. When these sensors are damaged, have poor connections, or experience signal interruptions, the vehicle's ECU cannot accurately obtain engine data, which triggers the engine warning light. Fuel or Oil Quality Issues: Failure to use the fuel or oil specified by the manufacturer may cause engine wear, leading to the illumination of the warning light. Poor Combustion of Air-Fuel Mixture: Poor combustion can result in engine carbon buildup or knocking. Once detected by the oxygen sensor and reported to the ECU, the warning light will illuminate as a warning. Issues such as faulty spark plugs, defective ignition coils, fuel pump failure, or clogged fuel lines can all cause poor combustion of the air-fuel mixture. Turbocharger Problems: The intake boost piping or turbocharger can also trigger the engine warning light. The most common issue is a damaged turbocharger, often accompanied by symptoms like oil leaks, excessive oil consumption, reduced power, metallic noises, or blue/black smoke from the exhaust. Intake Problems: If the vehicle's intake system is compromised, it may lead to clogged engine pipes, and in severe cases, the engine warning light will illuminate. A dirty or uncleaned air filter can cause intake issues. Exhaust Problems: Exhaust system faults can also trigger the engine warning light. Common causes include faulty rear oxygen sensors, catalytic converter issues, or problems with the exhaust camshaft and bearings. The catalytic converter is the most frequent culprit. Using leaded gasoline, lead- or silicon-based lubricant additives, physical damage to the catalytic converter, or fuel system malfunctions can all contribute to catalytic converter failure. Anti-Theft System Malfunction: If the vehicle's electronic anti-theft system fails or if the anti-theft controller is incompatible with the engine ECU, the anti-theft system may prevent the engine from operating normally, accompanied by the illumination of the engine warning light. If the engine warning light illuminates, follow these steps: First, check whether the engine is running normally. Look for symptoms like shaking or black smoke. If present, avoid restarting the engine. Note: Never restart the engine if the warning light is red. If the engine can be started, turn it off and wait 5-10 minutes. Without pressing the brake, press the start button once or turn the key halfway to the 'ON' position (without depressing the clutch). The vehicle will perform a self-diagnostic check upon powering up. Wait 5-10 seconds to see if the warning light turns off. If the warning light remains on, visit a service center as soon as possible. Technicians can use a portable diagnostic tool to retrieve trouble codes, identify the issue, and perform targeted repairs.

15

2

Share

What Causes the ABS Light to Appear on the Dashboard?

ABS light can illuminate in various states, and different states have different causes and solutions. The details are as follows: State 1: ABS warning light stays on (most common). Cause 1: The ABS speed sensor's sensing part is covered by dirt, mud, or other contaminants, affecting its ability to detect the corresponding speed signal. This prevents the ABS computer from determining the vehicle speed and wheel slip rate, thus failing to issue appropriate commands to adjust braking. Solution: Clean the dirt from the speed sensor and adjust the gap between the sensor and the signal ring to restore normal function. Cause 2: Poor signal transmission due to loose system wiring connections or poor contact in the ABS relay, leading to system failure. Solution: Check wiring connections and reconnect any loose parts. State 2: ABS warning light intermittently illuminates but turns off during acceleration. Cause: When multiple vehicle electrical devices are in use, the battery voltage drops below 10.5V. The ABS light turns off as the engine speed increases and voltage rises. This may also occur due to insufficient power supply voltage to the ABS system, such as poor terminal contact or grounding issues. Solution: Check the battery's specific gravity, charging system, and power supply (e.g., voltage relay or poor power contact). State 3: ABS warning light stays on after engine start and turns off only when the engine is turned off (IGFF). Cause: Poor grounding contact in the ABS hydraulic valve body; poor contact in the ABS hydraulic valve body wiring connector; ABS computer malfunction. Solution: Loosen and retighten the hydraulic valve body's grounding screw, cleaning the contact surface if necessary. Check for enlarged gaps in the connector; replace the ABS or ABS/ASR computer if needed. State 4: ABS warning light illuminates during high-speed driving. Cause: The ABS computer detects a significant difference between rear and front wheel speeds during high-speed driving; incorrect tire or wheel rim specifications. Solution: Refer to the vehicle's tire and wheel rim specifications, as indicated on the label near the fuel tank cap. State 5: ABS warning light intermittently illuminates. Cause: Improper adjustment of the brake light switch; poor internal contact in the brake light. Solution: With the engine running, press the brake pedal and manually push the brake switch lever down completely, then release the pedal to reset its position. Replace the brake light switch if necessary. If the ABS warning light is on, it is not recommended to continue driving. A lit ABS light indicates a malfunction in the vehicle's anti-lock braking system. During emergency braking, locked wheels can cause the vehicle to skid uncontrollably, preventing the driver from slowing down or adjusting the vehicle's trajectory, posing significant safety risks.

8

1

Share

What Are the Main Causes of Low Cylinder Pressure?

The causes of low cylinder pressure include air leakage between the cylinder head and the cylinder, leakage between the spark plug gasket and the cylinder head or a faulty decompression valve, crankcase leakage, and leakage due to severe wear between the piston rings and the cylinder or stuck piston rings. The diagnostic procedure can be carried out in the following order: 1. Air leakage between the cylinder head and the cylinder: Rotate the engine by foot and carefully observe the joint surface between the cylinder head and the cylinder for oil foam. If oil foam is present, it indicates leakage at the cylinder head gasket. In this case, check whether the tightening nuts on the cylinder head are properly tightened. If they are loose, tighten them evenly. If oil foam still appears after tightening, remove the cylinder head and inspect the cylinder head gasket for damage. If damaged, replace it with a new one. When removing the cylinder head and finding severe black carbon deposits at the leakage site, check the cylinder head for damage or warping and perform repairs or grinding. When replacing the cylinder head gasket, use original manufacturer parts. If making a gasket yourself, pay attention to the material and thickness. If made from soft aluminum plate, the material may be too hard to ensure sealing; if made from non-metallic materials, it may be easily burned or damaged by high-temperature, high-pressure gases in the combustion chamber. The thickness of the cylinder head gasket directly affects the engine's compression ratio—increased thickness reduces the compression ratio, while decreased thickness increases it. Therefore, the thickness of the cylinder head gasket must not be altered arbitrarily. 2. Air leakage between the spark plug gasket and the cylinder head or a faulty decompression valve: Damage to the spark plug gasket, surface contamination, or even forgetting to install the spark plug gasket can cause air leakage. During diagnosis, rotate the engine and carefully check around the spark plug for oil foam or hissing sounds indicating outward air leakage. If leakage is detected, clean the spark plug gasket, reinstall it, or replace it with a new one.

12

0

Share

Can the ETC be repositioned after installation?

The ETC can be removed and repositioned after installation. However, the ETC device will become invalid if removed by yourself, as it has an anti-tamper feature. There is a small switch on the back of the ETC electronic tag, which automatically turns off once the tag is peeled off the windshield. Therefore, you must take your vehicle's registration certificate to the ETC service provider for reactivation. ETC Billing Principle: There are one or more ETC lanes on highways. Through dedicated short-range microwave communication between the vehicle-mounted electronic tag installed on the windshield and the microwave antenna in the ETC lane at toll stations, the system uses computer networking technology to settle payments with banks in the background. This allows vehicles to pay tolls without stopping at toll booths, all based on the principle of "pass first, deduct later." Benefits of Installing ETC: Save time: Eliminates the hassle of waiting in line. Green and eco-friendly: Low-carbon, as vehicles pass through toll stations without stopping, reducing noise and exhaust emissions and minimizing pollution. Reduce wear and tear: Saves costs by decreasing the frequency of vehicle starts and stops, lowering wear and fuel consumption. Improve efficiency: Theoretically, ETC lanes can increase vehicle throughput by 2-3 times, making traditional ETC systems faster, newer, and more high-tech. More policy support: The State Council explicitly stated in the "13th Five-Year Plan for the Development of a Modern Comprehensive Transportation System" that "by 2020, intercity transportation card interoperability will be basically achieved in key urban clusters, and the proportion of vehicles equipped with ETC will significantly increase." It also set a target in the "13th Five-Year Plan" for comprehensive transportation development: "By 2020, the ETC usage rate for road passenger vehicles should reach 50%." More future possibilities: In addition to continuously improving the convenience of ETC installation and usage rates for passenger vehicles, efforts will be made to promote ETC usage for trucks and explore deeper integration of ETC systems with vehicle-to-vehicle communication, vehicle-road coordination, and other smart transportation developments. This will provide comprehensive travel services for car owners, meaning more application scenarios will support ETC. Precautions for Installing ETC: Do not obstruct the driver's view; it's best to install it behind the rearview mirror: Many car models have windshields with a steep incline, which can reduce the driver's field of vision. If ETC installation doesn't account for this, it may increase blind spots. Installing it behind the rearview mirror on the right side avoids obstructing the view. Do not interfere with charging: The ETC electronic tag consumes power but generally doesn't require charging or battery replacement, as it has a solar panel on the back for self-charging. Therefore, avoid installing it on the windshield's shaded areas or positions that might block the solar panel. Notes for Using ETC: The ETC transaction sensing range is 8 meters. To prevent issues caused by the ETC device of the vehicle in front, maintain a distance of at least 10 meters to avoid automatic payment for the vehicle ahead. The ETC lane recognition speed is 20 km/h; driving too fast may result in failed deductions due to unreadable device information. When using a debit card linked to ETC, insufficient balance may also cause payment failures.

9

0

Share

Can You Make a U-Turn on a Yellow Dashed Line?

U-turns are permitted on yellow dashed lines when there is no 'No U-Turn' sign and it does not interfere with normal traffic flow. However, making a U-turn on a solid line is prohibited and constitutes a traffic violation. According to the 'Road Traffic Safety Law,' violators will be fined 200 yuan and receive 3 penalty points. On long roads, solid or dashed white or yellow lines are typically found in the middle sections or before intersections. U-turns are strictly prohibited on solid lines. Permissible U-turn scenarios: U-turn is allowed at intersections with U-turn signs: If there is a clear U-turn sign at an intersection, a U-turn is permitted. If there is a U-turn traffic light, follow its instructions. If there is no traffic light, proceed with caution, ensuring no interference with other vehicles or pedestrians. U-turn is allowed at intersections without explicit 'No U-Turn' or 'No Left Turn' signs: If there are no signs explicitly prohibiting U-turns, you may proceed. 'No explicit prohibition' means the absence of 'No U-Turn,' 'No Left Turn,' or solid center lines. U-turns are also allowed on yellow grid lines: Yellow grid lines are no-parking zones, usually marked at intersections prone to congestion, important entrances, or other designated areas. Stopping on these lines (including waiting at traffic lights) is a violation. However, U-turns are permitted on yellow grid lines unless there is a central barrier. These lines effectively mean 'U-turn allowed.' Intersections with U-turn traffic lights: This is straightforward—if there is a U-turn light, proceed only when it is green. When 'No Left Turn' and 'U-turn Allowed' signs coexist: U-turns are permitted, but left turns are prohibited. Note that 'No U-Turn' and 'No Left Turn' are not the same. Precautions when making a U-turn: Check road markings: If the line is solid, U-turns are prohibited under any circumstances. Continue driving to find a suitable location. If there is a 'No Left Turn' sign, U-turns are also prohibited at that intersection, even if 'No U-Turn' is not explicitly mentioned, as U-turns inherently involve a left turn. U-turns must be made from the innermost left-turn lane. If you are in the second left-turn lane, U-turns are not allowed at that intersection. Always yield to oncoming traffic before making a U-turn. Failing to do so will make you liable for any accidents. Near intersection stop lines, lanes often have guiding arrows. Not all leftmost lanes have left-turn arrows; some may have straight arrows. Even without explicit 'No U-Turn' signs, U-turns are prohibited in such lanes. U-turns are not allowed on pedestrian crosswalks and constitute a traffic violation.

11

4

Share

What are the reasons why Haval cannot start?

The following are the specific reasons why Haval cannot start: Ignition wire failure: There may be issues such as aging ignition wires, incorrect cylinder wire sequence, damaged distributor, or loose spark plug caps. When the engine starts, there is a noticeable sound of the starter working, indicating that the power supply is normal and the starter can function properly. The problem may lie in a blocked fuel line, causing insufficient fuel supply. Incorrect gear position: Generally, the P or N gear is the starting position for automatic transmission vehicles. If the gear is in R or another position, not only will the car fail to start, but it also poses certain safety risks. Once an incorrect gear position is detected, adjust it promptly.

11

4

Share

What is the fuel consumption of the Tiggo 8 1.6t?

What Causes the Engine Warning Light to Illuminate in the Captiva?

What Causes the ABS Light to Appear on the Dashboard?

What Are the Main Causes of Low Cylinder Pressure?

Can the ETC be repositioned after installation?

Can You Make a U-Turn on a Yellow Dashed Line?

What are the reasons why Haval cannot start?

What are the exam subjects in driving school?

How Does the Crawl Control System Work?

What is the method for upgrading the navigation system in a Geely Emgrand?

How to Correct a Reversed Rearview Camera Display?