What is the fuel consumption of the SYM Fiddle 4?

3 Answers
Journey
07/28/25 7:14pm
The combined fuel consumption of the SYM Fiddle 4 is 5.2-5.6L/100km. Currently, there are 6 models of the SYM Fiddle 4 available for sale. The combined fuel consumption of the Trend Start version is 5.2L/100km. The Trend Enjoy and Trend Run versions have a combined fuel consumption of 5.3L/100km. The Trend Run Pro, Trend Cross Max, and Trend Cross versions have a combined fuel consumption of 5.6L/100km. The above figures are NEDC combined fuel consumption, which is the data measured under the NEDC test procedure for combined driving conditions. The actual fuel consumption is higher than this value, around 5.6L. When driving, the following 5 tips can help reduce fuel consumption: During the starting process, the vehicle should start in a low gear, gently press the accelerator, and gradually increase speed. Avoid suddenly pressing the accelerator hard, as this can multiply fuel consumption. Light acceleration, light braking, and early braking: While driving, gently press the accelerator to avoid sudden increases in engine speed and prevent the car from shaking during operation, thereby making the car more fuel-efficient. By anticipating road conditions and applying slow and even acceleration or braking, fuel economy can be improved by up to 20%. Maintain proper tire pressure: Keep tire pressure at the level recommended by the manufacturer. For every 2 PSI below the recommended value (equivalent to about 0.2 in metric units relative to the standard pressure of 2.4), fuel consumption increases by 1%. Regular vehicle maintenance or inspection: Timely oil changes can reduce carbon buildup (carbon buildup can cause ignition issues, sluggish acceleration, increased fuel consumption, and in severe cases, even cylinder misfires); regularly check and replace the air filter if dirty, and clean or replace the fuel injectors, spark plugs, and throttle body as per mileage. Close the windows while driving. Driving with windows open increases wind resistance, and the greater the wind resistance, the more resistance the car faces, requiring more power and thus increasing fuel consumption.
Was this review help?
15
0
Share
MollyLynn
08/11/25 11:06pm
I usually commute to work on my Fit 4, with urban fuel consumption around 2.8 liters per 100 kilometers. This data comes from my actual measurements - a full tank (just over 7 liters) can last me more than 200 kilometers. The recent fuel price hikes haven't affected me much since it only costs about 0.2 yuan per kilometer. Weekend suburban rides show better fuel efficiency, with my lowest record being 2.5 liters. Road conditions are the biggest factor affecting consumption - traffic jams can push it up to 3 liters, so I recommend avoiding rush hours.
Was this review help?
1
1
Share
Expand All
VeraDella
09/30/25 5:10am
Having ridden motorcycles for seven or eight years, my actual measured fuel consumption for the Fit 4 ranges between 2.5 to 3.2 liters. This scooter is equipped with a water-cooled 125cc engine, with an official theoretical fuel consumption of 2.3 liters, but actual usage depends on driving habits. I've tested under different conditions: cruising at a steady 40 km/h yields 2.6 liters, while carrying a passenger uphill peaks at 3.1 liters. It's recommended to regularly clean the throttle body and maintain tire pressure at the standard values of 1.8 (front) and 2.0 (rear) to keep long-term fuel consumption stable below 2.7 liters. Compared to Japanese scooters, it's slightly higher by 0.3 liters, but the power response is more direct.
Was this review help?
4
2
Share
Expand All
More Forum Discussions

What car brand has a horse on its logo?

The logo featuring a horse is the emblem of Baojun. The design of Baojun's brand logo aligns with its name both visually and phonetically, with the raised horse head symbolizing the company and brand's tribute to car owners and users. Baojun is an independent automotive brand established by SAIC-GM-Wuling, offering products across various segments including sedans, MPVs, SUVs, and new energy vehicles. Taking the 2021 Baojun 510 as an example, it is positioned as a compact SUV, featuring a MacPherson strut front suspension and a torsion beam rear suspension. In terms of powertrain, the vehicle is equipped with a 1.5L naturally aspirated engine delivering a maximum horsepower of 99 PS, peak torque of 135 Nm, and maximum power output of 73 kW.
18
5
Share

What to Do When the Car Clutch Gets Waterlogged?

Solutions for a waterlogged car clutch: First, turn off the engine to check if gear shifting is possible. If gear shifting is feasible with the engine off, it generally indicates a minor issue. If the clutch has only a small amount of water, there is a hole near the flywheel ring gear where the water should be spun dry quickly. Below is related information: 1. The car clutch is located inside the flywheel housing between the engine and the transmission. The clutch assembly is secured with screws to the rear plane of the flywheel, with the clutch output shaft serving as the transmission input shaft. 2. While driving, the driver can press or release the clutch pedal as needed to temporarily disconnect or gradually engage the engine and transmission, thereby cutting off or transmitting the engine's input power to the transmission.
3
1
Share

What is the principle of the eccentric shaft sensor?

The principle of the eccentric shaft sensor is based on the magnetoresistive effect. The eccentric shaft sensor is equipped with two independent angle sensors with opposite characteristics. When the nearby magnetic field changes position, the ferromagnetic conductor changes its own resistance. Relevant information about the eccentric shaft sensor is as follows: 1. Introduction: The eccentric shaft sensor detects the position of the eccentric shaft when equipped with an electronic valve control system. The eccentric shaft adjusts the camshaft to achieve the optimal intake valve lift in each operating state (the intake valve lift can be adjusted steplessly). 2. Measurement range: The measurement range of the sensor is 180°. The sensor is supplied with 5V voltage by the engine control unit DME. Data from the eccentric shaft sensor to the DME is transmitted at a medium clock frequency of 250kHz.
13
4
Share

What Should the Tire Pressure Be in Winter?

In winter, the appropriate tire pressure for cars is between 2.2 and 2.4 bar. Tire pressure refers to the air pressure inside the tires, and the level of tire pressure plays a significant role in the performance and power of the vehicle. Methods to check tire pressure include: 1. Using instruments to measure tire pressure; 2. Visual inspection method; 3. Consulting staff at a 4S store. The impacts of low tire pressure are: 1. Affects driving: increases the contact area between the tires and the ground, making the steering wheel heavier and affecting driving; 2. Increases the risk of tire blowouts: tires are more prone to overheating, leading to blowouts; 3. Accelerates tire wear: enlarges the tire body, making it easier for cracks to appear on the inner and outer sides of the tire, speeding up rubber aging and increasing tire wear.
13
1
Share

How to Set Up One-Touch Window Roll-Up with Car Key?

Introduction to the one-touch window roll-up setting method: By pressing and holding the lock button on the car key for 5 seconds without releasing, the car owner can simultaneously roll up all windows to close them. Similarly, pressing and holding the unlock button for 5 seconds without releasing will simultaneously lower all windows to open them. Below is an introduction to the one-touch window roll-up feature: 1. Applicable objects: The one-touch window roll-up function only works for the driver's side door; the other three doors are not equipped with this feature. Besides cost reduction, manufacturers also consider passenger safety. 2. Purpose: The one-touch window roll-up/down function is primarily designed to prevent drivers from being distracted by window operations while driving, thereby reducing the risk of traffic accidents. This design enhances safety.
5
3
Share

Is There Compensation for Cars Submerged in Heavy Rain?

Cars submerged in heavy rain are eligible for compensation. 1. Explanation: Typically, auto insurance coverage for water damage includes rescue fees such as towing charges, as well as costs for repairing electronic components inside the vehicle, replacing engine oil, three filters, and labor fees for damages caused by heavy rain accidents. If the owner has not purchased additional water damage insurance, the insurer will only compensate for damages when the vehicle was stationary and submerged, provided no attempt was made to forcibly start the engine. 2. Applicability of "Water Damage Insurance": This insurance covers situations where, during heavy rain or flooding, the insured vehicle is submerged up to the exhaust pipe or air intake, and the driver attempts to start the vehicle or uses inertia to start it; or when the vehicle is started without necessary post-flooding procedures. In these two scenarios, purchasing water damage insurance is necessary to receive corresponding compensation.
11
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.