What is the fuel consumption of the Suzuki GW250?

What brand of engine does Geely use?

Geely's engines are independently developed by Geely Auto, so they are domestically produced engines. Geely's models use self-developed engines. For example, the Emgrand uses the JLY-4g15 engine model, with a maximum power of 80kW, maximum horsepower of 109, and maximum torque of 140N·m. Here are some daily maintenance methods for Geely's engines: Use lubricating oil of the appropriate quality grade. For gasoline engines, choose SD--SF grade gasoline engine oil based on the additional devices in the intake and exhaust systems and usage conditions. For diesel engines, select CB--CD grade diesel engine oil according to mechanical load, with the selection standard not lower than the manufacturer's requirements. Regularly change the oil and oil filter. The quality of any grade of lubricating oil will change during use. After a certain mileage, performance deteriorates, causing various problems for the engine. To avoid malfunctions, change the oil regularly based on usage conditions and maintain an appropriate oil level. When oil passes through the fine holes of the filter, solid particles and viscous substances in the oil accumulate in the filter. If the filter is clogged and oil cannot pass through, the filter may burst, or the safety valve may open, allowing oil to bypass through the bypass valve, bringing contaminants back to the lubrication areas and accelerating engine wear and internal contamination. Regularly clean the crankcase. During engine operation, high-pressure unburned gases, acids, moisture, sulfur, and nitrogen oxides from the combustion chamber enter the crankcase through the gap between the piston rings and cylinder walls, mixing with metal particles from component wear to form sludge. Small amounts remain suspended in the oil, while larger amounts precipitate, clogging filters and oil passages, making engine lubrication difficult and causing wear. Regularly use a radiator cleaner to clean the radiator. Removing rust and scale not only ensures the engine operates normally but also extends the overall lifespan of the radiator and engine.

16

3

Share

Why does the Q5 sunroof make noise on sunny days?

Solution: Adjust the sunroof by moving it up, down, forward, and backward. Apply 3M double-sided tape in various places. When opening the sunroof and manually tapping it, noticeable shaking was observed at the rear. Loosen the six sunroof fixing screws, forcefully push the rear of the sunroof upward to its limit, then slightly tighten the rear screws. Visually, the rear should be slightly higher than the fixed position. Next, adjust the front of the sunroof downward slightly, ensuring it is visually just below the roofline. The goal is to make the rear of the sunroof tilt upward as much as possible. After a few days of driving, the noise should disappear. Below is an introduction to the Q5: 1. Powertrain: Equipped with a 2.0TFSI inline-four engine paired with a 7-speed Stronic dual-clutch transmission, it delivers ample power, smooth gear shifts, and quick acceleration. Users praise its strong sense of push-back. 2. Interior: The domestic Q5 features a rationally designed and clean interior layout, with rich and practical configurations and a strong technological feel. The cabin craftsmanship is refined, and the materials used are of high quality.

19

4

Share

Should Shock Absorbers Be Replaced Individually or in Pairs?

Shock absorbers should be replaced in pairs. They are used to dampen the oscillations from the spring's rebound after absorbing shocks and to mitigate impacts from the road surface. The reasons for replacing shock absorbers in pairs are: 1. Shock absorbers from different batches may have varying hardness levels; 2. There can be significant performance differences between old and new shock absorbers; 3. In emergency situations requiring sudden steering, if the shock absorbers have different elasticity, it may increase the risk of vehicle rollover. The functions of shock absorbers include: 1. Buffering the movement of the vehicle's center of gravity and conserving energy; 2. Reducing wind resistance and lessening the impact of changes in the vehicle's center of gravity on the tires. The steps for replacing shock absorbers are: 1. Remove the shock absorber along with the spring, then use a spring clamp to secure the spring; 2. After replacing the shock absorber, release the spring clamp and reinstall both components together.

18

1

Share

What is the method to distinguish Mercedes-Benz taillights?

Mercedes-Benz taillights can be distinguished as follows: the S-class taillights feature three horizontal bars, while the C-class and E-class taillights have two horizontal bars. The classification of car lights includes: 1. Headlights: Located at the front of the car, primarily for illumination and signaling; 2. Combination taillights: Positioned at the rear of the car, mainly for illumination and signaling; 3. Turn signals: Used to indicate left or right turns; 4. License plate lights: Primarily to illuminate the license plate, enabling identification of the vehicle's license plate at night. The maintenance methods for car lights are: 1. Check the seal of the headlights. If moisture enters the headlight, it will reduce the bulb's lifespan. Replace the sealing ring between the lens and reflector immediately if damaged; 2. Clean the bulbs. Use alcohol-soaked cotton swabs to remove dust and dirt from the bulbs. After cleaning, let them dry and avoid touching the bulbs with hands or cloth; 3. Clean the reflector. Use clean cotton dipped in hot water for cleaning, but do not scrub to avoid damaging the reflector's coating.

8

1

Share

What is the normal tire pressure for a Jeep Compass?

The standard tire pressure range for a Jeep Compass is 2.4-2.5 bar. Due to seasonal factors, the tire pressure can be appropriately increased by 0.2 bar in winter and reduced by 0.1 bar in summer. This data is based on the international GBT2978-2008 standard. The Compass's tire pressure monitoring system is displayed on the dashboard. The system provides real-time automatic monitoring of tire pressure during driving and alerts the driver to tire leaks or low pressure to ensure driving safety. Generally, a tire pressure exceeding 2.8 bar is considered too high, while a tire pressure below 2.0 bar is considered too low. Hazards of overinflated tires: Reduced tire friction and adhesion, affecting braking performance; causes steering wheel vibration and deviation, reducing driving comfort; accelerates wear on the central tread pattern, shortening tire lifespan; increases vehicle vibration, indirectly affecting the lifespan of other components; overstretches tire cords, reducing elasticity and increasing the load on the vehicle during driving. Hazards of underinflated tires: Increased friction coefficient with the road surface, leading to higher fuel consumption; makes the steering wheel heavy and prone to deviation, compromising driving safety; increases movement in various tire parts, causing abnormal heat due to excessive rolling; reduces the functionality of cords and rubber, leading to delamination or cord breakage and excessive friction with the rim, damaging the bead area and causing abnormal wear; multiplies friction between the tire and ground, sharply raising tire temperature, softening the tire, and drastically reducing strength. High-speed driving may result in a blowout. If the tire pressure monitoring indicator light comes on (a yellow symbol with an irregular circle, no seal on top, four small spikes below, and an exclamation mark inside), there are generally three possible reasons: Abnormal tire pressure: Typically, an alarm is triggered if the pressure is below 1.8 bar or above 3.0 bar. In this case, the tires need to be checked and the pressure adjusted. Tire pressure monitoring not reset: After inflating the tires, if the tire pressure monitoring system is not reset in time, it will continue to display the previous data, causing the indicator light to come on. Simply reset the tire pressure monitoring system to resolve this issue. Damaged tire pressure sensor: The tire pressure sensor, which monitors tire pressure, is installed inside the tire and connected to the inflation valve. If the sensor is damaged due to impact while driving, the tire pressure warning light will illuminate. For sensor damage, the only solution is to replace it with a new component.

6

0

Share

What engine does the Subaru BRZ use?

Subaru BRZ uses a 2.0-liter naturally aspirated engine with the code name FA20. This engine has a maximum horsepower of 200, a maximum power of 147 kilowatts, and a maximum torque of 205 Newton meters. The Subaru BRZ is a hardtop sports car produced by Subaru and is an imported model. The body dimensions of the Subaru BRZ are 4240 millimeters in length, 1775 millimeters in width, and 1285 millimeters in height, with a wheelbase of 2570 millimeters. The car adopts a front-engine, rear-wheel-drive layout, with a front MacPherson independent suspension and a rear double-wishbone suspension.

1

5

Share

What is the fuel consumption of the Suzuki GW250?

What brand of engine does Geely use?

Why does the Q5 sunroof make noise on sunny days?

Should Shock Absorbers Be Replaced Individually or in Pairs?

What is the method to distinguish Mercedes-Benz taillights?

What is the normal tire pressure for a Jeep Compass?

What engine does the Subaru BRZ use?

Why does the car dashboard show abnormal tire pressure?

When will the 2020 Tiggo 8 be launched?

What are the differences between the Red Badge Civic and the regular version?

How to Reset the Tire Pressure on a Subaru Outback?