What is the fuel consumption of the Oshan Kosai?

What kind of driver's license is required to drive an 11-seater Jinbei?

To drive an 11-seater Jinbei, a B1 driver's license is required. A1 and A2 driver's licenses are also acceptable. Below are the relevant details: 1. Detail one: Type B driver's licenses include B1 and B2, corresponding to medium-sized buses and large trucks respectively. 2. Detail two: If a Type B driver's license holder has demerit points recorded, they must report to the traffic management department of the public security authority within thirty days after the end of the current scoring cycle for verification. During verification, they must participate in no less than three hours of study on road traffic safety laws and regulations, safe and civilized driving, emergency handling, and other related knowledge, and receive case-based education on traffic accident warnings.

15

5

Share

What Causes the Yellow Engine Warning Light to Illuminate?

The illumination of the yellow engine warning light signifies a warning, indicating that certain system parameters in the vehicle may have exceeded the set range. The vehicle can still be driven at this time, but some functions may be limited. There is also a red engine warning light. When the red warning light comes on, it means the vehicle must stop immediately, turn off the engine, and driving is prohibited until the fault is checked. There are mainly seven reasons for the engine warning light to illuminate: Sensor malfunction: The sensors referred to here include those for coolant temperature, crankshaft position, air flow, intake temperature, oxygen, etc. When these sensors are damaged, have poor contact, or their signals are interrupted, the vehicle's ECU cannot accurately obtain engine data, triggering the engine warning light. Fuel or oil quality issues: Failure to add fuel and engine oil as required by the manufacturer may cause engine wear, leading to the warning light illuminating. Poor mixture combustion: Poor combustion can lead to engine carbon deposits or knocking. Once detected by the oxygen sensor and reported to the ECU, the warning light will illuminate as an alert. Issues such as faulty spark plugs, ignition coils, fuel pumps, or clogged fuel lines can cause poor mixture combustion. Turbocharger issues: Problems with the intake boost pipes or turbocharger can also trigger the engine warning light. The most common issue is turbocharger damage, often accompanied by symptoms like oil leaks, excessive oil consumption, reduced power, metallic noises, or blue/black smoke from the exhaust. Intake problems: If the vehicle's intake system is compromised, it may lead to clogged engine pipes, and in severe cases, the engine warning light will illuminate. A dirty air filter that hasn't been cleaned regularly can cause intake issues. Exhaust problems: Exhaust system faults can also trigger the engine warning light. Common causes include faults in the rear oxygen sensor, catalytic converter, exhaust camshaft, and bearings, with the catalytic converter being the most frequent issue. Using leaded gasoline, lead- or silicon-containing lubricant additives, physical damage to the catalytic converter, or fuel system malfunctions can easily cause catalytic converter failure. Anti-theft system malfunction: If the vehicle's electronic anti-theft system fails or if there's a mismatch between the anti-theft controller and the engine's electronic controller, the anti-theft system can prevent the engine from operating normally, simultaneously triggering the engine warning light. If the engine warning light illuminates, follow these steps: First, check if the engine is running normally. Look for signs of shaking, smoke, etc. If present, avoid restarting the engine. Note: Under no circumstances should the engine be restarted if the red warning light is on. If the engine can be started, turn it off and wait 5-10 minutes. Without pressing the brake, press the start button once or turn the key halfway to the 'on' position without depressing the clutch. The vehicle will perform a self-check upon powering up. After 5-10 seconds, observe whether the warning light on the dashboard turns off. If the warning light remains on, visit a service center as soon as possible to diagnose the issue. The service center can use a portable diagnostic tool to read the fault codes, identify the problem, and perform targeted repairs.

11

2

Share

What Causes a Car to Surge?

Car surging is most likely caused by issues with the engine's vacuum tube or idle speed motor. Below are some relevant introductions regarding car engine maintenance: 1. Maintain good crankcase ventilation: Pollutants in the air can deposit around the PCV valve, potentially causing it to clog. If the PCV valve is blocked, contaminated gases can flow backward into the air filter, polluting the filter element and reducing its filtering capacity. Inhaling excessively dirty air-fuel mixture further pollutes the crankcase, leading to increased fuel consumption, accelerated engine wear, and even engine damage. Therefore, it is necessary to regularly maintain the PCV and clean the pollutants around the PCV valve. 2. Regularly change the engine oil and oil filter: As the oil passes through the fine pores of the oil filter, solid particles and viscous substances in the oil accumulate in the filter. If the filter becomes clogged, the oil cannot flow smoothly through the filter element, which may cause the filter element to burst or open the safety valve, allowing oil to bypass through the bypass valve and carry contaminants back to the lubrication areas. This accelerates engine wear and increases internal contamination.

9

1

Share

What is the warning light icon for low coolant?

The coolant level warning light will illuminate on the dashboard if the coolant is low. Methods to determine if coolant is low: Observe the coolant warning light on the dashboard. If it lights up, it is likely due to low coolant, though it could also be caused by excessively high engine temperature. Check the coolant reservoir. If the level is below the minimum mark (MIN), do not continue driving and add coolant promptly. Inspect the water level marks on the coolant reservoir. The normal coolant level should be between the maximum and minimum marks. If the coolant is below the minimum mark, it indicates a low coolant level. Method for replacing coolant: Before fully replacing the coolant, conduct a thorough inspection to check for any leaks or cracks in the pipes, with particular attention to the five-way hose. The five-way hose is named for its five connections to different parts of the engine, and coolant flows through it to be distributed to various parts of the car. If there are signs of coolant leakage in this area, replace the hose or reseal the connections as needed. Drain the old coolant, then flush the system with clean water. Add clean water to the coolant reservoir and let it circulate through the engine cooling system. Start the engine and let it idle for 3 to 5 minutes to allow the water to circulate. Initially, the water draining out will have a faint pink color. Continue flushing with clean water until the drained water is clear. Remember to remove the heater hose to drain the water from the heater system. After draining for about an hour, add new coolant through the radiator hose to allow it to flow quickly into the radiator. Then, add another bottle of coolant to the reservoir until it is nearly full. Start the engine and let it run for about 10 minutes. As air is purged from the system, the coolant level will drop. Top up the coolant to the maximum mark "MAXT" on the reservoir.

2

5

Share

What is the difference between BMW windshield washer fluid and ordinary windshield washer fluid?

There is no difference. Windshield washer fluid is not particularly demanding, and there is no need to use any special brand; ordinary windshield washer fluid will suffice. Below are the functions of windshield washer fluid: 1. Cleaning performance: Surfactants typically have functions such as wetting, permeating, and solubilizing, thereby aiding in cleaning and removing dirt. 2. Antifreeze performance: The presence of alcohol and ethylene glycol can significantly lower the freezing point of the liquid, thus providing antifreeze effects and quickly dissolving frost. 3. Anti-fog performance: A single-molecule protective layer forms on the glass surface. This protective film prevents the formation of fog droplets, ensuring the windshield remains clear and transparent with a clear view. 4. Anti-static performance: After cleaning with windshield washer fluid, substances adsorbed on the glass surface can eliminate the charge on the glass surface, providing anti-static properties. 5. Lubrication performance: The ethylene glycol in the washer fluid has a high viscosity, which can provide lubrication, reducing friction between the wiper and the glass, and preventing scratches. 6. Anti-corrosion performance: Windshield washer fluid contains various corrosion inhibitors, which are completely safe and non-corrosive to any metals, automotive paint, or rubber.

2

5

Share

The Difference Between Direct Injection and Multi-Point Fuel Injection

In fact, direct injection engines and multi-point fuel injection engines cannot be directly distinguished as better or worse without specific performance requirements; the choice between them depends on the consumer's individual needs. Direct Injection Engine: A direct injection engine can be understood literally—it involves high-pressure nozzles directly injecting fuel into the combustion chamber to complete the engine's operation cycle. Advantages: Precise fuel control, faster and more immediate throttle response. Disadvantages: Since the fuel is directly injected into the cylinder for combustion, the requirements for fuel quality and intake air quality are relatively higher. Multi-Point Fuel Injection Engine: Multi-point fuel injection has multiple nozzles, making the engine operation process less direct and quick compared to direct injection. Its advantages include: significantly less carbon buildup in the engine compared to direct injection, making maintenance and servicing easier and cheaper. Disadvantages: The fuel delivery system is more complex, affecting fuel efficiency. Below are the differences between multi-point fuel injection and direct injection: Fuel Quality: Direct injection has higher fuel quality requirements compared to multi-point fuel injection, with a compression ratio as high as 12. Cost: Due to the more complex components of direct injection, it is generally more expensive than multi-point fuel injection. This means that for the same car model, the direct injection version will cost more. Fuel Consumption: Direct injection engines consume significantly less fuel than multi-point fuel injection engines. Performance: Direct injection engines provide 10% higher power and torque compared to conventional engines of the same displacement. Technology: Multi-point fuel injection is a more mature technology, while direct injection is a newer and more advanced fuel injection technology. Maintenance: Multi-point fuel injection has a simpler structure, making it easier and more reliable to maintain compared to direct injection. Direct injection engine models are more fuel-efficient, making them suitable for those who drive frequently, as they can save significantly on fuel costs. Multi-point fuel injection is more suitable for those who only occasionally drive for leisure. Choosing a car isn't just about the engine—it requires a comprehensive evaluation based on multiple factors.

16

3

Share

What is the fuel consumption of the Oshan Kosai?

What kind of driver's license is required to drive an 11-seater Jinbei?

What Causes the Yellow Engine Warning Light to Illuminate?

What Causes a Car to Surge?

What is the warning light icon for low coolant?

What is the difference between BMW windshield washer fluid and ordinary windshield washer fluid?

The Difference Between Direct Injection and Multi-Point Fuel Injection

What does it mean when the SVS light is on in a Geely Vision?

Which holidays offer free highway tolls?

Where is the computer connector located on the Geely Vision X6?

Is it not allowed to stop during reverse parking?