What is the fuel consumption of the Mazda CX5?

1 Answers
DeReese
07/30/25 12:44am
The Mazda CX5 2.0I model has a fuel consumption of 8.0 liters per 100 kilometers, while the 2.5I model consumes 10.5 liters per 100 kilometers. Below is an introduction to the Mazda CX5: 1. Body dimensions: The car measures 4555 mm in length, 1842 mm in width, 1685 mm in height, with a wheelbase of 2700 mm. 2. Powertrain: (1) 2.0L naturally aspirated engine: Delivers 155 horsepower and a maximum torque of 200 Nm, with the maximum power achieved at 6000 rpm and the maximum torque at 4000 rpm. (2) 2.5L naturally aspirated engine: Produces 196 horsepower and a maximum torque of 252 Nm, with the maximum power achieved at 6100 rpm and the maximum torque at 4000 rpm. 3. Suspension: The Mazda CX5 features a MacPherson independent front suspension and a multi-link independent rear suspension. 4. Variants: The Mazda CX5 is available in both front-wheel drive and four-wheel drive versions, with the four-wheel drive models equipped with an on-demand four-wheel drive system.
Was this review help?
5
5
Share
More Forum Discussions

What does the fraction in the specification model of a socket wrench represent?

It represents the size of the wrench opening in inches. One inch equals 2.45 centimeters, and lengths smaller than one inch are expressed as fractions of an inch. For example: 1/2 means half an inch, and 1-1/2 means one and a half inches. Conventionally, one-eighth of an inch is called a 'fen'. For instance: 1/2 = 4/8 inches, which is called 'four fen'; 3/4 = 6/8 inches is called 'six fen'. Common specifications for socket wrenches include: 1/2×10"×36T, 1/4×6"×36, 3/8×7-1/2"×36, 3/4×20"×24. Differentiation of model specifications: Generally, the model specifications of ratchet wrenches are distinguished by the size of the square drive, the length of the ratchet, and the number of teeth inside the ratchet. For example, 1/2×10"×36T refers to a square drive of 1/2, a ratchet length of 10 inches, and 36 teeth on the gear. Common specifications include: 1/2×10"×36T, 1/4×6"×36, 3/8×7-1/2"×36, 3/4×20"×24, etc.
1
1
Share

What Causes a Motorcycle's Malfunction Light to Illuminate and Prevent Starting?

Reasons for a motorcycle's malfunction light illuminating and failing to start: Poor valve sealing: Incorrect valve timing, intake and exhaust valves not sealing properly. Fuel pump circuit failure: Fuel pump operating poorly due to circuit issues, short circuits, or burnout causing insufficient or interrupted fuel supply. Intake system: Blockages in the intake system, such as in the air filter or mass airflow sensor, preventing proper fuel combustion. Engine knocking: Primary cause of engine knocking is excessively rapid combustion. Knocking creates excessive piston impact force, striking cylinder walls and causing wear.
15
4
Share

How Long Does It Take for an Overheated Engine to Cause Cylinder Scoring?

Generally, if the actual water temperature exceeds the permissible range of the vehicle and continues to be driven, the car may stall or experience cylinder scoring within one or two kilometers. In severe cases, the engine may even be completely damaged. High water temperature can only be tolerated for a short period; prolonged exposure can cause significant harm to the engine. The specific reasons for high engine temperature are as follows: Water Pump Failure: Coolant circulates through the water pump. If the water pump is damaged, the coolant essentially loses its function, and the heat generated by engine combustion cannot be dissipated. Insufficient Coolant: It is common knowledge among car owners that insufficient coolant leads to increased water temperature. However, using water or substandard, low-quality coolant as a cooling medium can also cause the engine to overheat. Thermostat Failure: When the thermostat is damaged or stuck, the engine only has a minimal coolant flow, and the radiator cannot effectively dissipate heat. This results in low cooling efficiency, leading to high engine temperature.
20
4
Share

Are Motorcycles Licensed at the Vehicle Management Office?

Motorcycles are licensed at the vehicle management office. Bring the vehicle invoice, certificate of conformity, ID card, and the motorcycle itself to the vehicle management office for licensing. Documents required for licensing: For vehicles that are not imported through customs and are not exempt from safety technical inspections as stipulated by the competent department of motor vehicle products under the State Council, a motor vehicle safety technical inspection certificate must be submitted. Documents to be verified for licensing: The vehicle management office shall, within two days from the date of accepting the application, confirm the motor vehicle, verify the vehicle identification number (VIN) imprint, review the submitted documents and certificates, and issue the motor vehicle registration certificate, license plate, driving license, and inspection compliance mark.
1
1
Share

What is the difference between throttle cleaning and intake system cleaning?

The differences between cleaning the automobile intake system and cleaning the intake manifold are: 1. Different cleaning complexity: (1) Intake system: It is necessary to first clean the throttle, then the intake pipe, and finally the valve chamber. (2) Intake manifold cleaning: Directly clean the intake manifold. 2. Different cleaning parts: (1) Intake system: Corresponding cleaning of the three main parts related to the intake. (2) Intake manifold cleaning: Only clean the intake manifold. 3. Different cleaning agents used: (1) Intake system: Use valve chamber cleaner, intake passage cleaner, and throttle cleaner. (2) Intake manifold cleaning: Only intake passage cleaner is needed.
5
2
Share

How Often Should a Toyota Highlander Be Serviced?

An oil change service is required approximately every 5,000 kilometers. If using full synthetic oil, the service interval can be extended to around 7,500-8,000 kilometers. Vehicle minor and major services are as follows: 1. Minor service intervals: The timing for a minor service depends on the effective duration or mileage of the engine oil and oil filter used. The validity periods vary for different brands and grades of mineral oil, semi-synthetic oil, and full synthetic oil. Always follow the manufacturer's recommendations. Oil filters generally come in two types: standard and long-life. Standard oil filters are replaced together with the oil, while long-life filters have a longer service duration. 2. Major service intervals: Major services are based on minor services, typically alternating between these two maintenance types. The intervals vary by vehicle brand, so always refer to the manufacturer's guidelines.
19
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.