What is the fuel consumption of the manual Hyundai Elantra?

1 Answers
MadelynLynn
07/29/25 10:47pm
The combined fuel consumption of the manual Hyundai Elantra is 5.6L/100km. The above figure is the NEDC combined fuel consumption, which is the fuel consumption data measured under the NEDC test procedure. The actual fuel consumption is higher than this value, ranging from 5.6-7.3L/100km. The fuel consumption of a car is directly related to five major factors: driving habits, the car itself, road conditions, natural wind, and environmental temperature. Specific factors that can increase fuel consumption are as follows: Driving habits: Aggressive driving, such as sudden acceleration, frequent overtaking, and not easing off the throttle before red lights, can increase fuel consumption. The car itself: Cars with larger engine displacements generally consume more fuel than those with smaller displacements because larger displacements usually mean greater power, requiring more gasoline for combustion. Heavier cars also have higher fuel consumption because greater weight requires more driving torque. Road conditions: Driving on dirt roads, muddy roads, soft surfaces, or mountainous roads increases resistance and fuel consumption. Natural wind: Driving against the wind or on windy days increases car resistance and fuel consumption. Low environmental temperatures: When the engine block temperature is low, the injected gasoline during cold starts does not atomize easily, requiring more gasoline to be injected for combustion, thus increasing fuel consumption. Additionally, in low temperatures, the engine computer may control the engine to run at higher RPMs to warm up, which also increases fuel consumption.
Was this review help?
9
1
Share
More Forum Discussions

Will points be deducted for sitting cross-legged in the passenger seat?

Sitting cross-legged in the passenger seat does not result in point deductions. However, if passengers become too relaxed and adopt incorrect postures, sudden turns, braking, or accidents may lead to injuries ranging from sprains and fractures to even life-threatening situations. Hazards of sitting cross-legged in the car: When relaxed, some passengers may place one or both legs on the seat. Sitting cross-legged inherently carries many risks, such as causing diseases in the lower limbs, knees, and lumbar spine. During the ride, vehicle jolts and swaying can exacerbate these hazards. Even when wearing a seatbelt, the cross-legged posture can alter the belt's position, preventing it from effectively securing the passenger during emergencies. This is particularly dangerous as the impact on the abdomen and ribs cannot be transferred to the legs, leading to severe injuries. Hazards of placing legs on the dashboard: This posture obstructs the driver's view of the right-side mirror and road conditions, increasing the risk of right-side collisions. In the event of sudden braking or a frontal collision, the upper body may violently lurch forward. With legs placed too high, the body can be compressed into a "V" shape, subjecting the waist to extreme impact forces. Under high-speed and intense impacts, there is even a risk of high-level paralysis or suffocation. Additionally, this posture can interfere with the proper deployment of the front passenger airbag.
1
5
Share

What is the reason for BMW fan output stage detecting an open load circuit?

BMW fan output stage detects an open load circuit due to reasons such as coil overheating damage or absence of 220V AC input, as detailed below: Coil overheating damage: Prolonged use of the fan causes excessive dust accumulation, increasing the friction coefficient between the rotor and bearings, leading to rotor obstruction or even seizing, resulting in coil overheating damage. Solution: After powering off, open the rear cover of the fan, add a few drops of lubricating oil to the bearing sleeves at both ends of the rotor, and rotate the blades while adding oil until they move freely, thereby eliminating the blower fault. No 220V AC input: This may be due to the absence of 220V AC input or coil damage. Solution: Disconnect the power, separate the two lead wires of the fan from the power supply connection points, leaving them suspended. Turn on the power and carefully measure both ends of the power line with a test pen. If one end lights up and the other does not, it indicates the power input is normal, and the issue might be with the fan coil. If both ends do not light up, it suggests a problem with the power input line.
14
4
Share

Correct Method for Defogging the 2021 Sagitar

Press the car's brake pedal all the way down to prepare for starting the engine. Press the one-touch start button to start the engine, then let it idle for a while. Allow the engine to idle for about 10 minutes to raise the coolant temperature to normal operating levels. Press the AUTO button to activate the automatic climate control system. Press the defogger button to clear fog; press the front defogger control button to clear the windshield, or press the rear defogger control button for the rear window.
10
0
Share

How to Turn on the Atmosphere Light in Atenza?

Click the settings option on any interface of the multimedia system. Select the ambient lighting option. Click the manual option at the top. The vehicle's atmosphere light will then turn on. The color option allows you to adjust the color of the atmosphere light. The interior atmosphere light is a decorative lighting lamp, usually in colors such as red, blue, or green.
10
4
Share

How to Open a Door with a Mercedes-Benz Spare Key?

First, when the car door is locked and cannot be opened by external force, locate the keyhole on the driver's side door handle. The keyhole is usually on the right side of the driver's seat door handle. If there is no obvious keyhole, you need to flip open the cover on the right side of the handle. Then, you can insert the spare key to unlock the door.
9
5
Share

How to Shift to Neutral Gear When an Automatic Transmission Car Stalls?

Press the brake pedal of the automatic transmission car. Changing the gear lever position while the engine is off may cause transmission malfunctions when starting the vehicle. Turn the car key to the ST position. The dashboard of the automatic transmission car will light up, and the vehicle will start. Press the gear lock switch on the automatic transmission car's gear lever. Pull the gear lever of the automatic transmission car to the N position to shift into neutral gear.
10
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.