What is the fuel consumption of the Lexus ES200?

1 Answers
Matt
07/29/25 1:47pm
The Lexus ES200 comes in two models: the Lexus ES 2021 200 Excellence Edition and Luxury Edition, both equipped with a 2.0L 173-horsepower GW4N20 engine, with an NEDC fuel consumption of 8.9L per 100 kilometers. The fuel tanks of the two Lexus ES200 models are the same. The distance that can be covered with a full tank of fuel is as follows: Equipped with a 2.0L 173-horsepower GW4N20 engine and a 60L fuel tank, the distance that can be covered with a full tank is 60/8.9*100 = 674km. The fuel consumption of a car is directly related to five major factors: driving habits, the car itself, road conditions, natural wind, and environmental temperature. Specific factors that can increase fuel consumption are as follows: Driving habits: Aggressive driving, such as sudden acceleration, frequent overtaking, and not easing off the throttle before a red light, can increase fuel consumption. The car itself: Cars with larger engine displacements generally consume more fuel than those with smaller displacements, as larger displacements usually mean greater power, requiring more gasoline to burn and perform work. Heavier cars also consume more fuel because greater weight requires more driving torque. Road conditions: Driving on dirt roads, muddy roads, soft surfaces, or mountainous roads increases resistance and fuel consumption. Natural wind: Driving against the wind or on windy days increases the car's resistance and fuel consumption. Low environmental temperatures: When the engine block is cold, the gasoline injected during a cold start does not atomize easily, requiring more gasoline to be injected for combustion, which increases fuel consumption. Additionally, in low temperatures, the engine's computer may control the engine to run at higher RPMs to warm up, further increasing fuel consumption.
Was this review help?
20
4
Share
More Forum Discussions

What does it mean when the EPC light in a car comes on?

There are several reasons why the EPC light in a car may illuminate: 1. The throttle body is dirty and needs cleaning. 2. There is a malfunction with the brake switch or wiring. 3. There is an issue with the intake system. 4. The fuel being used does not meet the required standards. Additional information: Introduction to EPC: EPC (Electronic-Power-Control) stands for Engine Electronic Power Control System. This system consists of various sensors, controllers, and other components. When a sensor malfunctions or detects an abnormal condition, the control system will take appropriate measures based on pre-programmed settings.
5
2
Share

What is the reason for one brake light bulb being on and the other not?

The reason for one brake light bulb being on and the other not is: the filament of the brake light has melted. When used for a certain period, aging is quite normal, causing the brake light to fail to function properly, and it needs to be replaced promptly. A damaged brake light switch can affect the rear vehicle's accurate judgment of the braking action. A faulty brake light switch can result in the brake light staying on, not lighting up, or flickering intermittently. The method to replace the brake light switch: 1. Remove the protective panel above the brake and accelerator pedal to access the brake light switch; 2. Unplug the corresponding wiring harness and directly remove the brake light switch; 3. Install a new brake light switch and reassemble the components in the reverse order.
18
5
Share

How to Reset the Engine Malfunction Light Yourself?

To reset the engine malfunction light yourself, you can try removing the fuse to clear the fault codes. Common reasons for the engine light to illuminate include: 1. Overheating of the engine cooling system or cylinder block; 2. Failure of the catalytic converter; 3. Malfunctioning mass airflow sensor; 4. Throttle body issues. The functions of the engine malfunction light are: 1. To alert the driver by signaling that a fault has been detected and needs attention; 2. Before starting the engine, when the ignition is turned on, if the light does not illuminate (with the engine off), it indicates a fault in the warning light circuit; 3. To display fault codes—specific flash patterns can be used to retrieve stored fault codes from the engine control unit.
11
2
Share

How to Remove Adhesive from Car Film?

The methods to remove adhesive from car film are: 1. Use vinegar to remove adhesive. Apply vinegar evenly on the residual adhesive with a cotton swab, wait for the vinegar to blend with the adhesive, then slowly remove it with a cloth or scraper; 2. Use essential balm to remove adhesive. Apply the essential balm multiple times on the adhesive, then slowly scrape it off with a knife; 3. Use car heat insulation cleaner to remove adhesive. Spray the specialized car heat insulation cleaner on the adhesive to be removed, and the adhesive will melt immediately, then wipe it off with a cloth; 4. Use alcohol to remove adhesive. Apply alcohol on the adhesive to soften it, then slowly scrape it off with a knife. The main functions of car film are to block ultraviolet rays, reduce heat, prevent injuries caused by flying glass, reduce glare, and protect personal privacy based on the one-way transparency of the solar film.
18
5
Share

How to Disassemble a Buick LaCrosse Key?

Buick LaCrosse key disassembly method is: 1. Open the folded key head; 2. Use a flat-head screwdriver to pry the gap of the key slot; 3. Separate the key into two parts, one with the electronic identification chip and the key head, and the other is the battery-powered remote; 4. Use a screwdriver to pry open the shell of the remote. The Buick LaCrosse is a mid-size sedan with a body length of 5026mm, width of 1866mm, height of 1462mm, and a wheelbase of 2905mm; it is equipped with a 2.0-liter turbocharged engine and a 9AT transmission, delivering a maximum horsepower of 241 Nm, maximum torque of 350 Nm, and maximum power at 5000 rpm; the front suspension uses a MacPherson independent suspension, and the rear suspension uses a multi-link independent suspension.
10
0
Share

What does the N in automatic transmission mean?

In automatic transmissions, N stands for Neutral. The N gear is typically used for brief stops, allowing the driver to remove their right foot from the brake pedal. However, when parked on a slope, the brake must still be applied to prevent the vehicle from rolling. Its primary function is to disconnect the power source between the engine and transmission, preventing prolonged brake pedal pressure that could raise transmission fluid temperature and potentially degrade the fluid, affecting transmission performance. Automatic transmissions feature the following gear positions: P, R, N, D, S, and L. The P (Park) gear is for extended parking, especially on inclines, as it mechanically locks the wheels to prevent vehicle movement. R (Reverse) requires pressing a safety button on some vehicles before shifting into reverse. N (Neutral) is used during vehicle startup or towing. S (Sport) mode enables free gear shifting for enhanced performance. L (Low) is for reduced speed and improved fuel efficiency in snowy conditions or heavy traffic.
20
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.