What is the fuel consumption of the Infiniti QX50?

1 Answers
VonKathryn
07/29/25 7:39pm
The fuel consumption of the Infiniti QX50 is 7.4L-10.3L. Driving speed affects fuel consumption: For a new car that has just left the factory, although it has undergone a break-in period, the surface of the parts is still relatively rough. For a car in the break-in period, it is essential to control the driving speed and avoid excessively high speeds. The speed should ideally be maintained between 50-80 km/h. Throttle usage affects fuel consumption: Avoid pressing the throttle too hard in a new car to ensure that pistons, cylinders, and other critical components increase their load under moderate conditions. This allows the parts to fully contact, friction, adapt, and set, enhancing the car's ability to adjust to the environment and smoothing out any protrusions on the parts. The quality of the car's break-in period will significantly impact its lifespan, safety, and fuel efficiency.
Was this review help?
14
1
Share
More Forum Discussions

How to Remove and Replace a Seat Belt Buckle?

First, adjust the seat and remove the four fixing bolts on the front and back of the seat. Locate the wiring of the car seat and disconnect the sensor wire of the seat belt buckle. Remove the seat cushion, take off the seat airbag, then remove the bolt fixing the seat belt, and finally take out the seat belt buckle slot. Remove the sensor inside the seat cushion, install the new seat belt buckle slot onto the seat, connect the wiring, and tighten the bolts. Install the weight sensor and the new retractor onto the seat, and tighten them with a wrench.
20
3
Share

What is the method to reset the maintenance light on a Mercedes-Benz W221?

Turn the ignition switch to the first position. Simultaneously press and hold the 'OK' button (S110s6) on the multifunction steering wheel and the 'Answer/End' button on the right side for about 5 seconds. Select 'ASSYSTPlus workshop' and confirm by pressing the 'OK' button (S110s6). Use the 'Forward/Backward' button (S110s1) to select 'Service Performed' and confirm by pressing the 'OK' button (S110s6). Choose 'Complete (Full) Service' or 'Individual'.
6
1
Share

How to Repair Gear Slippage in a Tiller?

Gears only partially engage in width, the locking steel ball does not snap into the locking groove of the shift rail, or the shift lever end is severely worn. When the axial force on the gear exceeds the locking force generated by the locking spring, the sliding gear is pushed away, resulting in automatic gear disengagement. If the shift fork is deformed or severely worn, and the centerline of the sliding gear intersects at an angle with the shaft centerline, the sliding gear may move axially and disengage. Severe wear of the steel ball or positioning groove can also make it difficult to position the sliding gear during transmission, leading to gear disengagement. Bearing wear increases the clearance, causing a skewed thrust during gear engagement, which results in gear disengagement.
2
2
Share

How to Install the Intake Camshaft on BMW N46 Engine?

Before installing the camshaft, first install all bearing caps and check if the camshaft holes are misaligned. When installing the camshaft, the cam of cylinder 1 must face upwards without pressing the valves. First, tighten the bearing caps of the 2nd and 5th positions alternately in a diagonal pattern with a torque of 20 Nm, then install the bearing caps of the 1st and 3rd positions, and finally install the bearing cap of the 4th position. Install the camshaft half-moon key and timing gear, tighten the bolts to prevent camshaft sliding and reduce risks, with a torque of 80 Nm.
2
0
Share

Where is the engine of the 2021 RAV4 produced?

2021 RAV4's engine is domestically produced, with some components being imported. The engine model used in the 2021 RAV4 is the M20D-FKS, with a maximum horsepower of 171, maximum power of 126KW, maximum power speed of 4400-5000rpm, and peak torque of 209N.m. The vehicle's power performance is relatively smooth and has been known for its low fuel consumption and low maintenance costs. For the 2021 RAV4's engine, the following maintenance methods can be used daily: Use lubricating oil of appropriate quality grade. For gasoline engines, SD--SF grade gasoline engine oil should be selected based on the additional devices of the intake and exhaust systems and usage conditions; for diesel engines, CB--CD grade diesel engine oil should be selected based on mechanical load, with the selection standard not lower than the manufacturer's specified requirements. Regularly change the engine oil and filter. The quality of any grade of lubricating oil will change during use. After a certain mileage, performance deteriorates, causing various problems for the engine. To avoid faults, change the oil regularly based on usage conditions and keep the oil level moderate. When engine oil passes through the fine holes of the filter, solid particles and sticky substances in the oil accumulate in the filter. If the filter is blocked and the oil cannot pass through the filter element, the filter element may burst or the safety valve may open, allowing oil to pass through the bypass valve and bring dirt back to the lubrication parts, accelerating engine wear and internal pollution. Regularly clean the crankcase. During engine operation, high-pressure unburned gas, acid, moisture, sulfur, and nitrogen oxides from the combustion chamber enter the crankcase through the gap between the piston rings and cylinder walls, mixing with metal powder from part wear to form sludge. A small amount remains suspended in the oil, while a large amount precipitates, blocking the filter and oil holes, making engine lubrication difficult and causing wear. Regularly use a radiator cleaner to clean the radiator. Removing rust and scale not only ensures the engine works properly but also extends the overall lifespan of the radiator and engine.
7
1
Share

How to Deal with the Black Screen Issue on the Enclave Display?

If the central control screen goes black and does not light up, you can first try restarting the screen by turning the ignition on and off. If the issue persists, it is likely due to poor contact in the wiring. It is necessary to promptly check whether there is any loose connection in the wiring. It could also be because the power signal cable has aged. You can try replacing it with a new one. There might be an issue with the power signal cable. Check the power module. Prolonged use of the screen may cause the power supply module to malfunction, leading not only to lag but also requiring circuit optimization.
10
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.