What is the fuel consumption of the Honda Envix?

How Long Does It Take for Headlight Butyl Rubber to Dry

Under normal circumstances, the surface will dry in about an hour. However, for the butyl rubber to fully dry internally and achieve a leak-proof seal, it takes 1-2 days. Therefore, it's best to wait 2-3 days after applying the butyl rubber before using the headlights; otherwise, water leakage is highly likely. Butyl rubber is a thermoplastic adhesive in a coiled form, convenient for sealing purposes. It eliminates the need for glue injection machines while allowing the use of OEM headlight sealant to achieve factory-standard sealing effects. Simply press the coiled butyl rubber strip into the headlight groove and perform secondary heating with an oven or hot air gun to assemble the headlight unit. If the lamp housing is black, use black rubber; if gray, use gray rubber—a very user-friendly feature that makes it quite popular in the market. Headlight water ingress and fogging are often caused by inadequate sealing. However, it should be noted that headlights are not absolutely sealed, as there are vent holes at the back where moist air can enter. When the headlights are turned on, fog may form at the edges, which is a normal phenomenon. This means even OEM headlights can potentially leak or fog. Of course, professionally modified headlights have a very low leakage rate, less than 0.5%. But if the sealing is done improperly, the chances of water ingress can be significantly higher.

12

3

Share

Can You Continue Driving When the Tire Pressure is Low on the Highway?

When the tire pressure is shown to be low on the highway, you should not continue driving. You need to find an exit or service area to inflate and check the tire pressure, and perform tire repairs if necessary. Reference standards for adjusting tire pressure: According to the international GBT2978-2008 standard, the standard tire pressure is approximately 2.4-2.5bar for standard tires and 2.8-2.9bar for reinforced tires. On roads with significant bumps, it is appropriate to reduce the tire pressure by 0.1-0.2bar below the standard tire pressure. For long-distance highway driving, the tire pressure should not be too low; it is advisable to increase the tire pressure by about 0.2bar above the lower limit of the standard tire pressure. Effects of low tire pressure: It can cause the friction between the tire and the ground to multiply, leading to a sharp rise in tire temperature, softening of the tire, and a significant drop in strength. When driving at high speeds, this may result in a tire blowout. It can also increase tire deformation, making the sidewalls prone to cracking and generating flexing movements, which leads to excessive heat, accelerates rubber aging, causes fatigue in the cord layers, and may break the cords. Additionally, it increases the tire's contact area with the ground, accelerating wear on the tire shoulders.

17

3

Share

What is the working principle of a floating caliper disc brake?

The braking principle of a floating caliper disc brake: During braking, the piston first moves to the right, pushing the brake pad towards the brake disc. When it comes into contact with the brake disc, the friction at this point is relatively small and insufficient to stop the car. Subsequently, the brake caliper body moves to the left along the guide pin under the reaction force. Finally, both sides clamp the brake disc together, bringing the car to a halt. More details are as follows: 1. The working principle of a floating caliper disc brake differs from that of a fixed caliper disc brake. The floating caliper disc brake remains in a floating state during operation, with the wheel cylinder located on the inner side of the brake caliper and only half the number compared to the fixed type. During braking, it utilizes internal friction to generate a reaction force. 2. The floating caliper disc brake has no hydraulic components on the outer side, preventing vapor lock, and occupies relatively little space. Notably, it can incorporate a parking brake mechanism via the inner piston. The wear levels of the inner and outer friction pads differ, with inconsistent wear speeds during operation. Comparatively, the inner friction pad wears faster than the outer one. 3. On many cars, the brake is equipped with a friction pad warning device. After prolonged use, the friction pads will experience necessary wear. Once the wear reaches a certain level, the warning device will immediately alert the driver, reminding them that the brake friction pads need immediate replacement. 4. Generally, disc brakes are primarily used on the rear wheels of vehicles. However, this type of brake has a relatively wide range of applications. Compared to ordinary brakes, disc brakes also have a significantly longer service life.

10

1

Share

How to Suck Out Dents on the Hood?

For small dents on the hood, you can purchase a car dent repair tool online to suck them out yourself. For larger dents, it is necessary to drive the car to a repair shop or a 4S store and have professionals perform sheet metal repairs. The functions of the hood are as follows: 1. Airflow guidance. For objects moving at high speed in the air, the air resistance and turbulence generated by the airflow around the moving object directly affect its trajectory and speed. The shape of the hood can effectively adjust the direction of airflow relative to the car's movement and the resistance it generates, reducing the impact of airflow on the car. Through guidance, air resistance can be decomposed into beneficial forces, increasing the force of the front wheels on the ground, which is beneficial for the car's driving stability. The streamlined appearance of the hood is basically designed based on this principle. 2. Protection of the engine and surrounding pipeline accessories. Under the hood are important components of the car, including the engine, electrical circuits, oil circuits, braking system, and transmission system, etc., which are crucial to the vehicle. By improving the strength and structure of the hood, adverse effects such as impact, corrosion, rain, and electrical interference can be fully prevented, ensuring the normal operation of the vehicle. 3. Aesthetics. The exterior design of a vehicle is a visual representation of its value. As an important part of the overall appearance, the hood plays a crucial role in being pleasing to the eye and reflecting the concept of the entire car.

19

1

Share

Is running a red light captured from the front or the back?

Running a red light is generally captured from the back, using electronic cameras to take three photos for determination: a photo of the vehicle crossing the intersection stop line, including the traffic light showing red and the license plate number; a photo of the vehicle completely passing the stop line, including the traffic light showing red and the license plate number; and a photo of the vehicle continuing to move, comparing the vehicle's position to see if there is any change, including the traffic light showing red and the license plate number. Capturing these three photos can determine that the vehicle has run a red light. The act of running a red light is clearly defined in the "Road Traffic Safety Law." Article 26 states that traffic signals consist of red, green, and yellow lights. A red light indicates prohibition of passage, a green light indicates permission to proceed, and a yellow light serves as a warning. A red light is a traffic signal prohibiting passage, and if a vehicle proceeds through an intersection when the light is red, it constitutes the traffic violation of running a red light. Six scenarios of running a red light: Stopping immediately after crossing the line at a red light (when the light turns red, the vehicle cannot stop in time, and the front of the vehicle crosses the stop line): If the vehicle has just crossed the stop line when the light is red but stops immediately, this act of running a red light will not be penalized. However, if there is obvious movement after crossing the line, it will be penalized. The three photos captured by electronic cameras for running a red light are: the front wheels crossing the stop line, the rear wheels crossing the stop line, and the front wheels crossing the opposite stop line. Only when all three photos are present will it be considered running a red light, resulting in a 6-point deduction under the new regulations. Running a red light under the direction of a traffic officer (the signal light is red, but the officer signals to proceed): When there is a conflict between the traffic signal and the officer's gesture, the driver must obey the officer's on-site command. If the driver runs a red light due to the officer's command, they can obtain a diversion certificate from the local traffic police station to avoid penalties. If the driver disagrees with the penalty, they can appeal through administrative reconsideration or administrative litigation. Stopping after the entire vehicle crosses the line at a red light (failing to brake in time, causing the entire vehicle to cross the stop line): If the vehicle stops after completely crossing the stop line without further movement, it is not considered running a red light. However, this constitutes stopping beyond the line. According to Article 4, Item 5 of the "Road Traffic Safety Violation Scoring Standards," failing to drive or stop as required at an intersection results in a 2-point deduction. Reversing after stopping beyond the line (attempting to avoid penalties by reversing after stopping beyond the line at a red light): Vehicles are not allowed to reverse at railway crossings, intersections, one-way roads, bridges, sharp turns, steep slopes, or tunnels. Violations may result in a warning or fine. Accidentally running a red light behind a large vehicle (due to the large vehicle blocking the view, following it through the intersection): Drivers must maintain sufficient visibility to see the traffic signals ahead and ensure a safe braking distance. Generally, if a vehicle is captured running a red light behind a large vehicle, it is due to rushing through the intersection. This behavior will be penalized as running a red light. Proceeding through an intersection at a yellow light (passing through the intersection when the light turns yellow): Traffic authorities state that according to the "Regulations for the Implementation of the Road Traffic Safety Law of the People's Republic of China," vehicles that have already crossed the stop line when the yellow light is flashing may continue to proceed. If the driver continues to rush through after the yellow light has turned on, it will be considered running a red light if captured.

6

1

Share

Which One to Choose: Haval Chitu or Changan Unit?

For a stylish appearance, the Haval Chitu stands out first. Its exterior design is quite bold, especially the front grille with its chrome silver finish, giving it a high-end and premium look. The full-body kit and blackened wheels add a touch of dominance to the Haval Chitu's appearance, making it resemble the "Red Hare" of cars, seemingly capable of swift and agile movement. In terms of power, the Haval Chitu is built on the new Lemon Platform and comes equipped with a 1.5T engine across the lineup, delivering a maximum power of 135kW (184 horsepower) and a peak torque of 275 Nm. It is paired with a 7-speed wet dual-clutch transmission, offering direct power output and excellent smoothness, making for a superb daily driving experience. Additionally, it boasts numerous features, including a launch mode, 0-100 km/h acceleration in 7.7 seconds, a cockpit-inspired interior, and L2-level autonomous driving. In terms of practicality, the Haval Chitu shows great sincerity. Regarding space, the Haval Chitu measures 4470/1898/1625 mm in length, width, and height, with a wheelbase of 2700 mm, making it a standard compact SUV with a comfortable experience in both front and rear seats. The interior design exudes a strong sporty atmosphere, targeting primarily the young consumer market. Thus, the design style of the exterior and interior emphasizes a sporty vibe, with details like the seat stitching adding an excellent touch.

13

3

Share

What is the fuel consumption of the Honda Envix?

How Long Does It Take for Headlight Butyl Rubber to Dry

Can You Continue Driving When the Tire Pressure is Low on the Highway?

What is the working principle of a floating caliper disc brake?

How to Suck Out Dents on the Hood?

Is running a red light captured from the front or the back?

Which One to Choose: Haval Chitu or Changan Unit?

What is the name of the fund established by XPeng Motors?

What is the tutorial for replacing the ATSL cabin air filter?

How to Route the Wiring for a Rearview Camera?

Does the Honda CR-V have a naturally aspirated engine?