What is the fuel consumption of the Excelle 1.6 automatic transmission?

What Causes Starter Freewheeling?

The reasons for starter freewheeling: 1. Check whether the starter drive gear and engine flywheel ring gear are excessively worn or have missing teeth; 2. Verify the integrity and effectiveness of the friction clutch, and whether the spring tension meets the specified value; 3. Due to prolonged use and frequent exposure to high temperatures, the starter shift fork is prone to fatigue, distortion, and loss of performance. When starting the engine in a cold or low-temperature condition, freewheeling may occur. If the engine is restarted after a 15-second pause as specified, the freewheeling phenomenon may persist. Troubleshooting methods: 1. Disassemble and clean the starter, visually inspect the wear on the shift fork and shift fork ring for excessive wear or breakage, and repair or replace if necessary; 2. While checking the performance of the friction clutch, also inspect the spring tension, and replace if it falls far below the required specification; 3. Examine the wear on both the starter drive gear and the engine flywheel ring gear, or measure the tooth taper with specialized tools. Replace if excessively worn, and perform welding repairs if cracks are found.

5

4

Share

Which Gear is the Reverse Gear?

The position of the reverse gear varies depending on the vehicle model. Below are specific introductions for manual and automatic transmission vehicles: 1. For manual transmission vehicles, the parking gear and neutral gear are the same, located in the gap in the middle of the gear positions. When parking, it is essential to engage the handbrake. In most 5-speed cars, the reverse gear is located below the 5th gear. In a few vehicles, the reverse gear shares the same position as the 1st gear, but to engage reverse, you need to press down the gear shift knob and then shift into reverse. 2. In automatic transmission cars, the reverse gear is mostly positioned towards the front of the gear console, immediately after the P (Park) gear and before the N (Neutral) gear. Whether the car has a P gear or not, the reverse gear and the drive gear are always separated by the neutral gear. Additionally, to engage or disengage the R (Reverse) gear, you must press the brake pedal and either press the safety button on the gear shift handle or push down the gear shift lever.

3

1

Share

What Does a Crossover Vehicle Mean?

Crossover vehicles, as the name suggests, are models that cross the boundaries of vehicle types, combining the advantages of different models. Initially, crossover vehicles mainly referred to SUV models with sedan-like characteristics. Later, the term evolved to broadly describe models that freely combine elements of sedans, SUVs, MPVs, and other vehicle types. Below are the specific details about crossover vehicles: 1. The most notable feature of crossover vehicles is that they cannot be classified into any existing car category. They do not belong to sedans, SUVs, or MPVs, yet they encompass the advantages of all these vehicle types. With their perfect body proportions, refined and luxurious interiors, excellent handling, and elegant appearance, they surpass their peers in the same class. 2. Crossover vehicles prominently showcase the comfort, sportiness, practicality, luxury, and versatility pursued by the new generation of cars. The "Enjoy, Drive, Safety" crossover concept proposed by the Chrysler Group has become the standard for measuring the essence of today's crossover vehicles.

12

1

Share

What are the differences between Xiangling M1 and M2?

The differences between Xiangling M1 and M2 lie in the cargo compartment and wheelbase. Below are detailed introductions about the two models: Differences in the cargo compartment: For the M1 model, the cargo compartment is 3.05 meters long, 1.61 meters wide, and 1.7 meters high. In terms of body dimensions, the length, width, and height are 5230/1750/2580mm respectively, with a wheelbase of 2750mm. For the M2 model, the cargo compartment is 3.1 meters long, 1.71 meters wide, and 1.7 meters high. In terms of body dimensions, the length, width, and height are 5280/1850/2590mm respectively, with a wheelbase of 2850mm. Differences in wheelbase: The front wheelbase of the M1 is 1320mm, and the rear wheelbase is 1280mm. The front wheelbase of the M2 is 1410mm, and the rear wheelbase is 1320mm.

5

2

Share

Are the Three Major Components of the Eclipse Cross Domestic or Imported?

The three major components of the Eclipse Cross are domestic. More information about the three major components of a car is as follows: 1. The three major components of a car refer to the engine, chassis, and transmission. 2. Engine: The car engine is the device that provides power to the car, determining its power, economy, stability, and environmental friendliness. Depending on the power source, car engines can be classified into diesel engines, gasoline engines, electric vehicle motors, and hybrid systems. 3. Transmission: The car transmission is commonly referred to as the 'gearbox' in cars and the 'speed changer' in industrial machinery. It is a mechanical or hydraulic device for mechanical power conversion. 4. Chassis: The car chassis consists of four parts: the transmission system, running gear, steering system, and braking system. The chassis supports and installs the car engine and its various components and assemblies, forming the overall shape of the car. It also receives the power from the engine to enable the car to move and ensure normal operation.

2

0

Share

What Causes the Abnormal Noise When Pressing and Releasing the Clutch?

Reasons for abnormal noise when pressing the clutch: 1. Bearing damage: The release bearing is severely worn or lacks lubrication, or the bearing return spring is too soft, broken, or detached. 2. Loose rivets: The driven plate rivets are loose, the steel plate is cracked, or the damping spring is broken. 3. Damaged pressure plate spring: The clutch pressure plate spring is broken or the release bearing is loose. 4. Damaged release lever: The clutch release lever is broken, excessively worn, or the release lever adjustment bolt is broken. Extended content, diagnosis and troubleshooting of clutch abnormal noise: 1. Slightly press the clutch pedal to make the release lever contact the release bearing. If a 'grinding' sound is heard, it indicates abnormal noise from the release bearing. If the noise persists after lubrication, the bearing is excessively worn and should be replaced. 2. If the noise occurs when the pedal is fully pressed and disappears when released, it indicates loose or broken clutch damping springs. 3. If the noise occurs when the clutch just engages or disengages while repeatedly pressing the pedal, it indicates loose rivets or excessive spline wear. 4. If there is intermittent collision noise, it may be due to axial movement of the release bearing, and the release bearing return spring should be replaced.

1

5

Share

What is the fuel consumption of the Excelle 1.6 automatic transmission?

What Causes Starter Freewheeling?

Which Gear is the Reverse Gear?

What Does a Crossover Vehicle Mean?

What are the differences between Xiangling M1 and M2?

Are the Three Major Components of the Eclipse Cross Domestic or Imported?

What Causes the Abnormal Noise When Pressing and Releasing the Clutch?

How many kilometers can a full tank of gas last for the Trumpchi GM6?

Are the pre-exam secret papers for Subject 1 accurate?

Clutch Has No Pressure and Won't Spring Back, Can't Engage Gear?

What is the actual fuel consumption of the Bestune T99?