What is the fuel consumption of the Corolla 1.2T per 100 kilometers?

1 Answers
LeTalia
07/24/25 9:15am
The combined fuel consumption of the Corolla 1.2T is 5.5-5.6L/100km. There are currently 4 models of the Corolla 1.2T available for sale. The Pioneer PLUS version has a fuel consumption of 5.5L/100km, while the Elite PLUS, Flagship, and Luxury versions have a fuel consumption of 5.6L/100km. The above figures are the NEDC combined fuel consumption, which is the data measured under the NEDC test procedure for comprehensive driving conditions. The actual fuel consumption is higher than this value, ranging from 5.5-10.5L/100km. Specific factors affecting a car's fuel consumption are as follows: Vehicle weight: Larger and heavier cars tend to consume more fuel. Generally, a small family car with a 1.6L engine and a weight of around 1.2 tons has a fuel consumption of approximately 7.5 liters (calculated under full load conditions), while an SUV weighing around 1.5 tons has a fuel consumption of about 8.5 liters. Different weights result in varying fuel consumption. Drag coefficient: Higher drag increases fuel consumption during driving. Cars with better aerodynamics have lower drag coefficients, resulting in lower fuel consumption. Economical RPM: The engine has an optimal torque output point during driving. Maintaining the car's speed within this torque output range significantly reduces fuel consumption. Generally, small-displacement cars achieve this at around 70 km/h, while larger-displacement cars reach it at about 100 km/h. Staying within this economical RPM range ensures minimal fuel consumption. Driving style: Aggressive driving behaviors such as sudden acceleration, frequent overtaking, and not easing off the throttle before a red light can increase fuel consumption.
Was this review help?
10
3
Share
More Forum Discussions

How to Install a Tire Pressure Monitor by Yourself?

Unscrew the dust cap of the tire valve, then slide on the dust cover, install the hex nut, mount the tire pressure sensor, and tighten the sensor with a nut wrench. This completes the installation of one tire pressure sensor. Unscrew the dust cap of the tire valve. Slide on the dust cover, install the hex nut, mount the tire pressure sensor, loosen the sensor with a nut, check for air leaks, and the installation is complete. Tire pressure monitoring mainly comes in two types: indirect tire pressure monitoring and direct tire pressure monitoring.
17
3
Share

What are the pros and cons of adding wheel spacers to a car?

Adding wheel spacers can improve stability during sharp turns. Below is an introduction to the advantages and disadvantages of adding wheel spacers: 1. Advantages of adding wheel spacers to a car: (1) For some models with unsatisfactory body posture, adding wheel spacers slightly protrudes the wheels, enhancing the vehicle's visual sense of power. Wide-body modified cars may appear to have recessed tires, and wheel spacers can perfectly solve this issue. (2) Adding wheel spacers increases the track width on the same axle, improving the vehicle's tendency to feel unstable or roll during high-speed driving and sharp turns. (3) Wheel spacers are usually made of aluminum alloy, so they do not add much weight. (4) When upgrading to larger brake calipers, wheel spacers can provide the necessary clearance. 2. Disadvantages of adding wheel spacers to a car: (1) On uneven roads, the vehicle may experience more severe bumps, which can damage the universal joints on the half-shafts. (2) The quality of wheel spacers varies, and if a spacer fails, it can also damage the original wheel hub. (3) One factor in vehicle suspension tuning is to reduce abnormal tire wear. Adding wheel spacers changes the track width, leading to abnormal tire wear. (4) The vehicle should not be heavily loaded, as mentioned in the third point, because it can cause abnormal tire wear and sometimes result in rubbing against the wheel arches.
2
1
Share

What does the 'trip' on the Volkswagen car dashboard mean?

The 'trip' on the Volkswagen car display refers to the trip mileage, measured in kilometers (KM). Here is more information about trip mileage: 1. Trip mileage is a driving parameter that can accurately calculate fuel consumption data and record the total kilometers traveled. 2. Trip mileage can calculate the amount of fuel used during driving and can also be used to measure fuel consumption at different speeds. 3. The trip mileage can be reset or calculated using the lever on the left side of the steering wheel. 4. The remaining distance that can be traveled with the current fuel can be calculated based on the trip mileage data.
12
5
Share

What Causes Low Tire Pressure in One Tire?

A tire with low pressure may be due to tire damage or aging. The details are as follows: Tire Damage: When a car tire is damaged, it will inevitably lead to air leakage, resulting in low tire pressure over time. If a tire is damaged, it must be repaired or replaced promptly to prevent safety hazards. Tire Aging: There are many reasons for slow air leakage in car tires, including natural aging of the tire or prolonged parking. When a car is parked for an extended period, it should be placed on a flat and hard surface to prevent the tire from deforming due to long-term compression.
15
2
Share

How to Repair Damaged Car Wheels?

Here are the steps to repair scratched car wheels: 1. Clean the wheel to easily inspect all scratches, scratch depth, and whether the wheel is broken. If the wheel surface has cracks, deformation, or is completely broken, it cannot be repaired. Only wheels without breaks or deformation can be repaired; 2. After cleaning, use oil-removing wax paper to wipe the wheel clean; 3. After smoothing the putty, repaint the wheel. Spray the wheel paint onto the applied putty, gently spraying back and forth a few times to complete the entire wheel scratch repair process; 4. The scratched areas of the wheel are rough, so use fine sandpaper to smooth them out.
10
1
Share

How to Turn on the High Beam on the New Passat?

The high beam on the new Passat is activated by turning the rotary switch all the way to the right to turn on the low beam headlights, then pulling the lever on the left side of the steering wheel (the turn signal lever) backward to engage the high beam. This lever can be moved forward, backward, up, and down. Moving it up or down activates the left or right turn signals, pushing it forward flashes the headlights, and pulling it backward turns on the high beam. More details are as follows: 1. The intensity of the light is adjusted based on the distance of the filament. The high beam focuses light parallel, emitting a concentrated and bright beam that can illuminate distant and high objects. The low beam, focused beyond its focal point (between 1x and 2x the focal distance), emits a divergent light that illuminates a wider area at close range. The difference between high and low beams: both are used for nighttime lighting, but the high beam has a higher angle and longer range, while the low beam has a lower angle and shorter range. 2. It is generally advisable not to use the high beam when driving in the city, as urban areas usually have good lighting conditions. The high beam's high angle can easily dazzle oncoming drivers and pedestrians, impairing their vision and creating unsafe conditions, as well as being considered impolite driving behavior. The high beam can be used on highways or in rural areas without streetlights to expand the field of vision. However, when encountering oncoming traffic, it is recommended to switch to the low beam for safety and courtesy.
19
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.