What is the fuel consumption of the 8th generation Accord 2.0?

Why does the ABS light come on in Santana 3000?

When the ABS light is displayed on the car, it means there is a fault in the vehicle's anti-lock braking system. If the wheels lock up during emergency braking, the vehicle may lose control and skid, making it difficult for the driver to slow down or adjust the vehicle's trajectory, posing significant safety risks. There are various states in which the ABS light may illuminate, with different causes and solutions for each state, as detailed below: State 1: ABS warning light remains constantly on (most common). Cause 1: The ABS wheel speed sensor's sensing part is covered by dirt, mud, or other contaminants, affecting the sensor's ability to detect the corresponding speed signal. This prevents the ABS computer from determining the vehicle speed and wheel slip rate, thus failing to issue appropriate commands to adjust braking. Solution: Clean the dirt from the wheel speed sensor and adjust the gap between the sensor and the signal ring to restore normal function. Cause 2: Poor signal due to loose connections between system lines or poor contact in the ABS relay, leading to system failure. Solution: Check the line connections and reconnect any loose parts. State 2: ABS warning light intermittently comes on and turns off when accelerating. Cause: When multiple vehicle electrical devices are in use, the battery voltage drops below 10.5V. The ABS light turns off as the engine speed increases and voltage rises. The ABS system's power supply voltage is too low, possibly due to poor terminal contact or grounding issues. Solution: Check the battery's specific gravity; inspect the charging system; examine the power supply (e.g., voltage relay or poor power contact). State 3: ABS warning light stays on after engine start and only turns off when the engine is turned off. Cause: Poor grounding contact in the ABS hydraulic valve body; poor contact in the ABS hydraulic valve body's wiring connector; ABS computer failure. Solution: Loosen the grounding screw on the hydraulic valve body and then retighten it, cleaning the contact surface if necessary; check if the connector gap has widened; replace the ABS or ABS/ASR computer. State 4: ABS warning light comes on during high-speed driving. Cause: At high speeds, the ABS computer detects a significant discrepancy between the rear and front wheel speed signals; incorrect tire or wheel rim specifications. Solution: Refer to the vehicle's tire and wheel rim specifications, as indicated on the label near the fuel tank cap. State 5: ABS warning light intermittently comes on. Cause: Improper adjustment of the brake light switch; poor internal contact in the brake light. Solution: Start the engine, press the brake pedal, push the brake switch linkage down with your finger, then release the brake pedal to complete the self-setting position; replace the brake light switch.

3

0

Share

What are the reasons for the engine warning light in Peugeot 308?

There are mainly 7 reasons for the engine warning light in Peugeot 308: Sensor failure: The sensors mentioned here include water temperature, crankshaft position, air flow, intake temperature, oxygen sensor, etc. When these sensors are damaged, have poor contact, or signal interruption, the car's ECU cannot accurately obtain engine data, which will cause the engine warning light to come on. Fuel quality issues: If fuel and engine oil are not added as required by the manufacturer, it may cause engine wear and trigger the warning light. Poor mixture combustion: Poor mixture combustion can lead to engine carbon deposits or knocking. When detected by the oxygen sensor and reported to the ECU, the warning light will illuminate as a warning. Spark plug failure, ignition coil failure, fuel pump failure, and fuel line blockage can all cause poor mixture combustion in the engine. Turbocharging issues: The intake turbocharging pipeline and turbocharger can also cause the engine warning light to come on. The most common issue is turbocharger damage, accompanied by symptoms such as oil leaks, high oil consumption, reduced power, metal noises, and blue or black smoke from the exhaust pipe. Intake issues: If there is a problem with the car's intake, it may cause engine pipeline blockage, and in severe cases, trigger the engine warning light. A dirty air filter that is not cleaned regularly can lead to intake problems. Exhaust issues: Exhaust faults can also cause the engine warning light to come on. The rear oxygen sensor, three-way catalytic converter, exhaust camshaft, and bearing failures are all causes of exhaust problems, with the three-way catalytic converter being the most common. Using leaded gasoline, lead or silicon-containing lubricant additives, physical damage to the three-way catalytic converter, or engine fuel supply system failures can easily cause three-way catalytic converter issues. Anti-theft system failure: If the car's electronic anti-theft system malfunctions, or if the anti-theft controller does not match the engine electronic controller, the anti-theft system can also prevent the engine from working properly and trigger the engine warning light. If the engine warning light comes on, follow these steps: First, check if the engine is running normally and if there are issues such as shaking or black smoke. If so, avoid restarting the engine. Especially note that if the red light is on, do not restart the engine. If the engine can be started, turn it off for 5-10 minutes, then without pressing the brake, press the start button once or turn the key halfway to the 'on' position without pressing the clutch. The car will perform a self-check after powering on. Wait for 5-10 seconds and observe if the warning light on the dashboard goes off. If the warning light does not go off, visit a service station as soon as possible to diagnose the issue. The service station can use a portable diagnostic tool to read the fault code, obtain fault information, and perform targeted repairs.

9

3

Share

Should the Automatic Transmission Filter Be Replaced?

Automatic transmission filters do need to be replaced, typically alongside the transmission fluid change, approximately every two years or after driving 40,000 to 60,000 kilometers. The transmission filter, also known as the transmission screen, is installed inside the transmission and serves a filtering function. It removes impurities and contaminants from the transmission fluid, thereby protecting the transmission. An automatic transmission is a gear-shifting device that automatically changes gears based on the vehicle's speed and engine RPM, as opposed to a manual transmission. It mainly includes four types: hydraulic automatic transmission, continuously variable transmission (CVT), electronically controlled mechanical automatic transmission, and dual-clutch transmission.

11

1

Share

What to Pay Attention to During the First Maintenance?

First maintenance considerations: 1. The first maintenance time is calculated from the date of vehicle delivery; 2. There are two indicators for the first maintenance: mileage and time, whichever comes first will be the standard, exceeding either will affect the warranty; 3. The first maintenance time and maintenance cycle vary by vehicle, some cars require it at 2000 kilometers, while others may go up to 8000 kilometers, due to differences in specific technical conditions; 4. There is no need to perform the first maintenance ahead of schedule. Car maintenance mainly includes the engine system, transmission system, air conditioning system, etc., aiming to keep the car clean, maintain normal technical conditions, eliminate hidden dangers, prevent faults, and extend the service life.

2

1

Share

How to Adjust the Left and Right of Car High Beams?

Method for adjusting the left and right of car high beams: When adjusting the high beams yourself, it is recommended to find a wall, park the car about 1 to 1.5 meters away from the wall, turn on the high beams, and adjust the left and right of the high beams using the adjustment knob. If there is no adjustment knob, it is advised to visit a professional repair shop for adjustment. Proper adjustment can provide better visibility while driving. High beams adjust the intensity of the light based on the distance of the filament. At their focal point, high beams emit light in parallel, which is more concentrated and brighter, allowing illumination of distant and high objects.

10

5

Share

What is the check engine warning light?

checkengine is commonly referred to as the engine fault warning indicator light. The purpose of the light is to warn the driver of abnormal conditions in the engine, which may also be accompanied by engine noise, stalling, hesitation, vibration, or other abnormal conditions, or when other indicator lights illuminate simultaneously, directly affecting the vehicle's driving capability. In cases where the cause is uncertain, it is advisable not to continue driving for safety reasons, to avoid potentially more serious faults. The car dashboard is a device that reflects the working conditions of various vehicle systems, including common indicators such as the fuel indicator, washer fluid indicator, electronic throttle indicator, front and rear fog light indicators, and warning lights.

13

4

Share

What is the fuel consumption of the 8th generation Accord 2.0?

Why does the ABS light come on in Santana 3000?

What are the reasons for the engine warning light in Peugeot 308?

Should the Automatic Transmission Filter Be Replaced?

What to Pay Attention to During the First Maintenance?

How to Adjust the Left and Right of Car High Beams?

What is the check engine warning light?

What is the fuel tank capacity of the Subaru XV in liters?

Why Are Rally Cars Mostly Hot Hatches?

Where is the flasher located in the Wuling Hongguang?

What is the fuel consumption of Nissan Teana 2.5v6?