What is the fuel consumption of the 2021 Land Rover Range Rover Sport?

What is the recommended tire pressure for family sedans?

For family sedans, the general tire pressure should be maintained between 2.3-2.5 bar. The specific value can be referenced to the official recommended tire pressure for the vehicle, which is usually found in the vehicle's user manual, fuel tank cap door, or driver's door side. It can be slightly adjusted according to seasonal changes, with slightly higher pressure in winter and lower in summer. Additional information: 1. Checking the recommended tire pressure: Inflate the tires according to the manufacturer's recommended values. Owners can find the recommended tire pressure values in the vehicle's user manual or on the driver's door (near the B-pillar), fuel tank cap, or storage compartment where the tire model is indicated. 2. Introduction to recommended tire pressure: The recommended tire pressure usually refers to the tire pressure measured when the tires are cold. Definition of cold tires: At least three hours after parking or if the tires have not been driven more than 2 kilometers. If you can only measure the tire pressure when the tires are hot, subtract approximately 0.3 bar (=4 psi) from the measured value to get the cold inflation pressure.

12

2

Share

Why is urea added to the car?

Urea is added to the car to meet emission standards. The following are the effects of not using urea in a car: 1. Excessive emissions, causing environmental pollution; 2. Chemicals in the car's system may oxidize, leading to clogging of the urea nozzle and rendering the entire system useless; 3. Reduced vehicle power. Additional information: Below is more about adding urea to a car: 1. Reasons for the urea warning light: 1. Low urea pressure, high urea consumption; 2. Insufficient power, urea consumption too high or too low; dashboard malfunction. 2. Methods to eliminate the urea warning light: 1. Replace the urea solution; 2. Replace the water heating valve; replace the urea pump and power supply module connector. 3. The role of urea is: to treat exhaust gases, reduce pollutants in the exhaust, and optimize engine performance and fuel consumption.

19

0

Share

What are the steps for adjusting engine valve clearance?

The method for adjusting valve clearance is the cylinder-by-cylinder adjustment method. The following are the specific operation steps for the cylinder-by-cylinder adjustment method: 1. Check the valve clearance when the engine is cold; 2. Open the cylinder head cover and check in order. At the end of the compression stroke of each cylinder, check the intake and exhaust valve clearance of each cylinder respectively; 3. Shake the rocker arm by hand to check if the valve is stuck. When the piston is at the top dead center of the compression stroke and the rocker arm is loose, insert a feeler gauge into the valve clearance. The clearance value is determined when the feeler gauge can just pass through smoothly; 4. If the clearance does not meet the specified value, loosen the lock nut on the rocker arm and adjust the screw with a screwdriver. When the clearance reaches the specified value, tighten the lock nut with the screwdriver; 5. Recheck whether the clearance of each valve has been adjusted to the appropriate value.

14

4

Share

Can the car still be driven when the stop light is on?

When the car's stop light is on, it indicates that there may be issues with the engine, oil, water temperature, brakes, and other components. At this point, you should immediately stop the car for inspection and avoid driving further. The reasons for the stop light coming on are as follows: 1. Overheating: If the engine temperature is too high, it may cause malfunctions, and in severe cases, the engine may seize. 2. Brake damage: If the brake fluid is insufficient or the brake pads are severely worn, it can also trigger the stop light, requiring an immediate stop for inspection. 3. Battery depletion: If the battery is severely depleted and unable to sustain the car's operation, the stop light will come on, necessitating a stop to recharge the battery. 4. Insufficient oil pressure: If the engine oil level is low or the temperature is abnormally high, the car will alert you. 5. Driving with the handbrake engaged: Forgetting to release the handbrake while driving can also cause the stop light to illuminate.

3

1

Share

How many seconds does the Equinox take to accelerate from 0 to 100 km/h?

According to official data, the Equinox comes with two engine options: 1.5T and 2.0T. The 1.5T model accelerates from 0 to 100 km/h in 10.2 seconds, while the 2.0T model does it in 8.1 seconds. Factors affecting a vehicle's 0-100 km/h acceleration time include: Torque: Torque, in simple terms, represents how much force is available. The greater the torque, the more force is available to propel the vehicle, resulting in faster acceleration. For example, the Envision 1.5T has a maximum torque of 270 Nm and accelerates from 0 to 100 km/h in 8.4 seconds, while the Equinox 1.5T has a maximum torque of 250 Nm and takes 10.2 seconds. Transmission efficiency: The transmission acts as the medium for transferring power, inevitably involving power loss. Higher transmission efficiency leads to better acceleration performance. Generally, transmission efficiency ranks as follows: manual transmission > dry dual-clutch transmission > wet dual-clutch transmission > AT transmission > CVT transmission. The Equinox 1.5T is equipped with a 6-speed automatic transmission, while the 2.0T model has a 9-speed automatic transmission. Power-to-weight ratio: The relationship between horsepower and vehicle weight is called the power-to-weight ratio (measured in Hp/T). A higher power-to-weight ratio results in faster acceleration. For instance, the Envision 1.5T has a power-to-weight ratio of 123.39 Hp/T and accelerates from 0 to 100 km/h in 8.4 seconds, while the Equinox 1.5T has a ratio of 110.09 Hp/T and takes 10.2 seconds.

20

5

Share

What transmission does the Yixuan use?

Yixuan uses two types of transmissions, one is a 5-speed manual transmission, and the other is a 6-speed dual-clutch transmission. Yixuan is a compact car under the Dongfeng Fengshen brand, equipped with two engines: a 1.0-liter turbocharged engine and a 1.5-liter turbocharged engine. The 1.0-liter engine has a maximum power of 92 kW and a maximum torque of 196 Nm; the 1.5-liter engine has a maximum power of 110 kW and a maximum torque of 230 Nm. In terms of suspension, the Yixuan uses a MacPherson independent suspension at the front and a torsion beam non-independent suspension at the rear.

18

2

Share

What is the fuel consumption of the 2021 Land Rover Range Rover Sport?

What is the recommended tire pressure for family sedans?

Why is urea added to the car?

What are the steps for adjusting engine valve clearance?

Can the car still be driven when the stop light is on?

How many seconds does the Equinox take to accelerate from 0 to 100 km/h?

What transmission does the Yixuan use?

Why Can't I See My Scores After Passing All Subjects?

Solutions for High Pressure in LNG Cylinders

Are there any differences in appearance between the Tayron 330 and 380?

How to Play Music in an Older BMW 3 Series?