What is the fuel consumption of the 2021 Excelle four-cylinder model?

1 Answers
Ben
07/29/25 11:26pm
2021 Excelle four-cylinder model has a fuel consumption of 5.3L per 100 kilometers. The following are the specific details of the Excelle: 1. Vehicle Positioning: The Buick Excelle is a compact car under the Buick brand. The length, width, and height of the Buick Excelle are 4609mm, 1798mm, and 1464mm respectively, with a wheelbase of 2640mm. 2. Powertrain: The Buick Excelle's 1.3-liter turbocharged engine has a maximum power of 120kW and a maximum torque of 230Nm. The engine's maximum power is achieved at 5500 rpm, and the maximum torque is available between 1800 to 4400 rpm. This engine is equipped with a 48V mild hybrid system and multi-point fuel injection technology, and it uses an aluminum alloy cylinder head and block. This engine is paired with a 6-speed automatic transmission. The 1.5-liter turbocharged engine has a maximum power of 113 horsepower and a maximum torque of 141Nm. The engine's maximum power is achieved at 6000 rpm, and the maximum torque is available at 4400 rpm. This engine is equipped with DVVT technology and multi-point fuel injection technology, and it uses an aluminum alloy cylinder head and a cast iron cylinder block. This engine is paired with a 6-speed automatic transmission.
Was this review help?
6
4
Share
More Forum Discussions

Why does a car suddenly stall while running and then fail to start?

There are several main reasons why a car fails to start after stalling: ignition system, fuel supply system, intake and exhaust system, electrical system, and mechanical system failures. 1. Fuel supply system: Check for a damaged fuel pump, ruptured fuel lines, clogged carburetor fuel inlet, or an empty fuel tank. In such cases, the car can actually start. Remove the air filter, press the accelerator pedal, and if gasoline sprays from the carburetor's acceleration nozzle, it indicates the fuel system is functioning normally. 2. Electrical system: While driving, issues like low-voltage power failure or engine overheating causing anti-knock system failure can lead to stalling. Check the ignition and starter switch. Remove the central high-voltage wire and start the engine with the starter. If there's no spark from the central high-voltage wire, it indicates an electrical system problem. 3. Low-voltage circuit short causing stalling: This results in intermittent stalling. Inspect the low-voltage circuits. 4. Component failure: This usually involves the ignition coil, capacitor, or electronic ignition module. The car may start initially, stall after a while, restart, and then stall again. 5. Check for carbon buildup: If the car has run about 20,000 KM, focus on inspecting and cleaning the throttle body. 6. Test and inspect the starter, fuel pump, sensors, and other components related to the starting and fuel supply systems.
8
5
Share

What does the M1 gear mean?

M1 refers to the first gear in manual mode. Here is some additional information: 1. M gear, short for Manual, is the manual mode. It is generally used when going up or down slopes, entering parking garages, in traffic jams, or when following other vehicles. 2. When shifted into M gear, it switches to manual mode, requiring manual gear changes. The gear lever will have "+" and "-" symbols. Pushing the lever toward the "+" direction shifts up one gear, while pushing it toward the "-" direction shifts down one gear. Additional information: Common automatic transmission gears generally include the following: 1. P gear, Park. It is typically used when turning off and parking the vehicle. Many vehicles need to be in P gear to power off, remove the key, or lock the doors. After shifting into P gear, the vehicle's braking mechanism is locked. 2. N gear, Neutral. It is usually used for short-term parking. 3. D gear, Drive. D gear is the most commonly used gear. Shifting into D gear and pressing the accelerator will make the car move forward. 4. L gear, Low. Its function is to reduce speed and increase torque, commonly used when climbing slopes. 5. S gear, Sport. Shifting into S gear causes the car to shift up later or downshift earlier, keeping the engine at higher RPMs and increasing torque output for greater power. It is commonly used when overtaking.
12
1
Share

Is the Cadillac XT5 a Rebadged Envision?

The Cadillac XT5 is not a rebadged Envision; the planned XT4 is the model that shares a platform with the Envision. The Envision is derived from the A-level Delta II platform (used in the old Excelle and Cruze), while the XT5 is based on the B-level Sigma II platform (used in the Regal, LaCrosse, and XTS). Here are some key details about the Cadillac XT5: 1. Exterior: The Cadillac XT5 is a four-door, five-seat SUV with dimensions of 4812mm in length, 1903mm in width, and 1680mm in height, and a wheelbase of 2857mm. The trunk offers 584 liters of cargo space, and with the second-row seats folded down via a one-touch function, the space expands to a maximum of 1634 liters. 2. Powertrain: The Cadillac XT5 offers two differently tuned versions of a 2.0T turbocharged direct-injection engine, with maximum power outputs of 184kW and 198kW, respectively, and a peak torque of 400Nm for both. The engine is paired with an 8-speed automatic transmission featuring Start/Stop energy-saving technology.
12
4
Share

What does a three-cylinder car mean?

A three-cylinder car refers to a vehicle whose engine has only three cylinders. Common engines with displacements of 1.0 and 1.3 liters are typically three-cylinder engines. Advantages and disadvantages of three-cylinder engines: Advantages: The advantages of three-cylinder engines include: 1. Relatively lower fuel consumption. Fewer cylinders naturally result in smaller displacement, leading to reduced fuel consumption. 2. Compact size and lighter weight. The smaller size allows for better optimization of engine bay and even cabin layout, offering more flexibility compared to four-cylinder engines. Disadvantages: 1. Vibration: Due to design flaws, three-cylinder engines inherently suffer from idle vibration issues compared to four-cylinder engines. This is a major reason why many people hesitate to choose three-cylinder engines, as models like the Buick Excelle and BMW 1 Series cannot avoid this common problem. 2. Noise: Noise is another common issue with three-cylinder engines. Manufacturers attempt to mitigate it by adding sound insulation in the engine bay and using better soundproofing materials in the cabin, but the noise remains noticeable outside the vehicle. 3. Insufficient power: Although most modern three-cylinder engines employ turbocharging and direct injection technology, they often lack torque before the turbo kicks in, making them feel slightly underpowered at low speeds. Additionally, higher RPM settings result in slightly lower comfort and smoothness compared to four-cylinder engines.
17
3
Share

How Long Does It Take to Detect Not Wearing a Seat Belt?

Not wearing a seat belt is a traffic violation. If captured by an electronic eye, it usually takes about two to three days to be detected. Seat Belt Introduction: A car seat belt is a safety device designed to restrain occupants during a collision, preventing secondary impacts with the steering wheel or dashboard, or avoiding injuries or fatalities by being ejected from the vehicle. Working Principle: The retractor contains a ratchet mechanism. Normally, occupants can pull the webbing freely and evenly from the seat. However, when the webbing stops being pulled out continuously or when the vehicle encounters an emergency, the ratchet mechanism locks automatically, preventing further webbing from being pulled out.
10
0
Share

What does a wrench symbol on the car mean?

When a wrench symbol appears on the car, it is a maintenance indicator, reminding the owner that the vehicle needs servicing. Generally, manufacturers set this maintenance reminder function to alert owners to perform scheduled maintenance based on mileage. If the "small wrench" symbol still appears after normal maintenance, you can manually remove the "small wrench" symbol by following these steps: 1. Insert the key, but do not turn it. 2. Hold down the operating lever next to the odometer for 5-10 seconds, then turn the key to power on. 3. After another 5-10 seconds, start the car. Keep holding the operating lever throughout this process without releasing it. Usually, the small wrench symbol can be cleared after these steps. If it is not cleared, repeat the same process a few more times.
13
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.