What is the fuel consumption of Changan Oshan X7?

1 Answers
DeAriana
07/30/25 2:16am
Changan Oshan X7's actual fuel consumption is not fixed, ranging from 8-12L per 100 kilometers, while the MIIT comprehensive fuel consumption is 7.4L per 100 kilometers. The following is a detailed introduction to Changan Oshan X7: 1. Changan Oshan X7 is equipped with the Blue Whale 1.5TGDI engine, which has won the "China Heart Top Ten Engines" award. This new 280T engine has a maximum power of 131Kw and a maximum torque of 265Nm, surpassing same-displacement engines from brands like BMW, Buick, and Honda. It reaches the peak torque of 265Nm at 1450rpm. 2. Despite its powerful performance, the engine adopts strong scavenging technology, which uses the positive pressure difference between the intake and exhaust pipes to directly sweep fresh air into the exhaust system, reducing residual exhaust gas in the cylinder, improving charging efficiency, and enhancing engine performance. The low-end torque of the engine is increased by over 20%, significantly improving starting performance. The shift strategy is optimized to achieve engine downspeed, significantly reducing fuel consumption. 3. Changan Oshan X7 is matched with a DCT dual-clutch transmission developed by the UK R&D center, featuring rapid throttle response and excellent acceleration performance.
Was this review help?
12
3
Share
More Forum Discussions

What does adjustable headlight height mean?

Adjustable headlight height refers to the function of the front headlights that allows adjustment of the light projection angle. The methods to adjust the front headlights are: 1. The first knob next to the headlight switch, turning it upward raises the beam, and turning it downward lowers the beam; 2. Open the engine hood, and on the headlight box in the engine compartment, there is a white object with a cross-shaped knob inside. Use a cross screwdriver to rotate it left or right to adjust the height. The methods to repair car front headlights: 1. Check the degree of aging, cracking, and yellowing of the front headlights and use masking tape to cover the surrounding areas to prevent damage to the paint during sanding; 2. Choose sandpaper based on the severity of the front headlight condition; 3. After washing with water, let it dry or use a hair dryer to dry it; 4. Use a vaporizer cup to heat and fumigate the headlight until the front headlight shell becomes transparent.
7
5
Share

What is the method for adjusting car rearview mirrors?

Car rearview mirror adjustment method is: 1. Left rearview mirror: Place the horizontal line at the center line of the rearview mirror, then adjust the edge of the car body to occupy one-fourth of the mirror image; 2. Right rearview mirror: Place the horizontal line at two-thirds of the rearview mirror, then adjust the edge of the car body to occupy one-fourth of the mirror image. The method for judging the distance between cars by looking at the rearview mirror is: 1. Take the center of the rearview mirror as the reference line. When the car body is on the outer side of the reference line and the rear car cannot be fully seen, the distance is 5 meters; 2. When the rear car can fully appear in the rearview mirror and the car body is pressed on the reference line, the distance is 10 meters; 3. When the rear car is pressed on the central axis of the rearview mirror, and there is still a car width between the car in the rearview mirror and the outer edge of the rearview mirror, the distance is 15 meters.
18
3
Share

What is the method for applying auto body filler?

The method for applying auto body filler is: 1. Fill larger dents using a wider, rigid spreader, focusing on leveling rather than achieving a smooth finish; 2. Primarily fill low-lying areas with a thinner application than the first step, using a rigid spreader for flat surfaces and a rubber spreader for curved areas; 3. Fill pores left from the previous two steps, sandpaper marks, and minor dents. Auto body filler is a viscous substance composed mainly of extender pigments, drying agents, and solvents. It is applied to surfaces already coated with primer to fill defects such as dents, weld seams, and scratches on car bodies and components. Through successive layers of application and sanding, a flat and smooth surface is eventually formed.
10
2
Share

How to Open the Fuel Filler Cap on a Chevrolet Cruze?

The fuel filler cap of the Chevrolet Cruze is located on the right rear side of the car, which is the passenger side, near the rear of the vehicle. After locating the fuel filler cap, press the left side lightly to open it. If it does not open, you may press a few more times with slightly more force until the fuel filler cap opens. If the fuel filler cap cannot be opened by pressing directly, it can also be manually opened using the manual switch located inside the car's trunk. The Cruze is a compact car under SAIC-GM Chevrolet, featuring a MacPherson strut front suspension and a torsion beam rear suspension. In terms of dimensions, the car measures 4666mm in length, 1807mm in width, and 1460mm in height, with a wheelbase of 2700mm. For power, the Cruze is equipped with a 1.5L naturally aspirated engine, paired with a 6-speed manual transmission.
1
0
Share

What is applied to tires during car washing?

During car washing, what is applied to tires is tire protectant, also known as tire blackener. After spraying, the tires appear very black and shiny. Its function is to maintain the elasticity of the tire's structural molecules, making the tires more durable. Car tires are one of the important components of a vehicle, directly in contact with the road surface. Together with the car suspension, they help to mitigate the impacts encountered during driving, ensuring good ride comfort and smooth driving, as well as maintaining good adhesion between the wheels and the road surface. Precautions for car tires: 1. Regularly check tire pressure to ensure it is neither too high nor too low; 2. Frequently inspect the wear condition of the tires; 3. Promptly remove small stones and other foreign objects from the tires.
14
3
Share

What are the steps for using a dedicated automotive decoder?

Steps for using a dedicated automotive decoder: 1. Connect the diagnostic tool to the vehicle and open the corresponding software in the diagnostic tool to enter the diagnostic interface. The system will automatically identify the vehicle type and provide corresponding results. After diagnosis, basic vehicle information will appear; 2. Click on "Detect," and the system will perform an automatic detection. After the detection is complete, problematic items will be automatically displayed. An automotive decoder, also known as a vehicle fault diagnostic tool, is a professional automotive maintenance and testing device that can read computer data from the fault system. Automotive decoders can generally be divided into two types: one is for automotive engine or circuit faults, and the other is for central door locking systems, mainly used for the matching and testing of automotive remote controls.
7
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.