What is the fuel consumption of BMW X6 3.0t?

1 Answers
DelSophia
07/30/25 3:49am
The combined fuel consumption of BMW X6 3.0t is 10.0L/100km. Currently, there are 2 available models of BMW X6 3.0t: xDrive40i M Sport Package and xDrive40i Exclusive M Sport Package, both with a combined fuel consumption of 10.0L/100km. The above data refers to NEDC combined fuel consumption, which is measured under NEDC test procedures. The actual fuel consumption is higher than this value, approximately 13L/100km. Factors affecting vehicle fuel consumption are as follows: Vehicle weight: Larger and heavier vehicles tend to consume more fuel. Generally, a compact family car with 1.6L displacement weighing about 1.2 tons has a fuel consumption of around 7.5L (calculated under full load), while an SUV weighing about 1.5 tons consumes around 8.5L. Different weights result in varying fuel consumption. Drag coefficient: Higher drag increases fuel consumption during driving. Vehicles with better aerodynamics have lower drag coefficients, resulting in lower fuel consumption. Economical RPM: During driving, the engine has an optimal torque output point where fuel consumption is minimized. Generally, small-displacement vehicles reach this point at around 70 km/h, while large-displacement vehicles achieve it at about 100 km/h. Maintaining speed within this economical RPM range significantly reduces fuel consumption. Driving style: Aggressive driving behaviors such as sudden acceleration, frequent overtaking, and not easing off the throttle before traffic lights increase fuel consumption.
Was this review help?
9
0
Share
More Forum Discussions

Why does the car fail to start due to power steering failure?

Power steering failure preventing the car from starting is caused by a malfunction in the steering wheel assistance system. Here are some maintenance tips for the steering system: 1. Oil level check: With the engine running, ensure the oil level in the reservoir is between the upper and lower marks on the dipstick. 2. Visual inspection: Check the lubrication of mechanical connections in the steering system; open the steering fluid reservoir to inspect the oil level and cleanliness of the steering fluid and filter; examine steering rods and pressure bearings for damage or deformation; start the engine and turn the steering wheel left and right to check for excessive play or looseness in mechanical connections; lift the steering axle and shake the steering wheels up and down to inspect for play in the steering knuckle; start the engine to check the entire steering hydraulic system for oil leaks.
11
1
Share

Why is the reversing camera not displaying on the Leiling?

Display settings issue, camera malfunction, wiring problem, or scratched reversing camera. Detailed explanations for the Leiling reversing camera not displaying are as follows: 1. Display settings issue: There is usually a camera switch control in the display settings. Simply adjust the switch to "ON". 2. Camera malfunction: Inspect and replace the camera if necessary. 3. Wiring problem: This is the most common issue. The wiring harness for the reversing camera runs from the dashboard all the way to the trunk, covering a long distance. It is likely that there is a poor connection at some point in the wiring harness or plug, requiring careful inspection. 4. Scratched reversing camera: The surface of most cameras is very fragile, so it is necessary to apply a protective film over the camera.
1
0
Share

Is it allowed to change lanes over a solid white line?

Changing lanes over a solid white line at a traffic light is considered a traffic violation. "Crossing solid line violations" are the most common offenses committed by novice drivers, often due to carelessness. In fact, apart from crossing solid white lines, there are many other traffic markings that prohibit vehicles from driving over them. If caught, offenders will face fines and penalty points. Below is a summary of these lines that must not be crossed: 1. Solid white lines are used to separate lanes traveling in the same direction and are typically painted before traffic lights at intersections. Many drivers are photographed violating traffic rules by crossing these markings. 2. Single solid yellow lines are used to prohibit vehicles from crossing or driving over them in both directions. They are generally painted on roads with only one lane in each direction or one motor vehicle lane and one non-motor vehicle lane, or on sections where overtaking is prohibited due to other hazards. 3. Double solid yellow lines serve the same purpose as single solid yellow lines, prohibiting vehicles from crossing or driving over them in both directions. They are usually painted on roads with two or more motor vehicle lanes in each direction and without a physical central divider.
13
2
Share

What are the symptoms of a faulty Iveco EGR valve?

There are symptoms such as extremely unstable idling or even stalling, flashing malfunction indicator light, failure to meet annual emission inspection standards, burning engine oil, and blue exhaust smoke. Below are the relevant details: 1. Introduction: The EGR valve is a mechatronic product installed on diesel engines to control the amount of exhaust gas recirculated back into the intake system. It is usually located on the right side of the intake manifold, near the throttle body, and connected to the exhaust manifold via a short metal pipe. 2. Function: It controls the amount of exhaust gas entering the intake manifold, allowing a certain amount of exhaust gas to flow into the intake manifold for recirculation. The EGR valve is a very important and critical component in the exhaust gas recirculation system.
3
5
Share

What is the difference between semi-steel and full-steel tires?

The main difference between semi-steel and full-steel tires is that semi-steel tires use steel wires as reinforcement layers in the tread area, while the carcass is made of nylon or polyester materials. Full-steel tires, on the other hand, use steel wires not only in the tread but also throughout the entire carcass to bear the load. Below are the relevant details: 1. Both semi-steel and full-steel tires are radial tires: Both semi-steel and full-steel tires are radial tires. The arrangement of the carcass cords in radial tires differs from that in bias-ply tires. In radial tires, the cords are not arranged in a crisscross pattern but are nearly parallel to the tire cross-section, resembling the arrangement of Earth's meridians, with a small cord angle, typically 0°. 2. Advantages of radial tires: There are no intersecting points between the carcass cords. When the tire is in motion, the stress around the crown increases, leading to circumferential stretching and radial cracking of the carcass. Therefore, the belt layer of radial tires uses cords arranged nearly circumferentially, intersecting the carcass cords at an angle of 90°, typically between 70° and 78°, forming a nearly inextensible rigid annular band that secures the entire tire and limits its circumferential deformation.
2
4
Share

What are the symptoms of sensor failure in the Audi Q3?

Audi Q3 sensor failure symptoms: 1. Oxygen sensor poisoning: Oxygen sensor poisoning is a frequently occurring and difficult-to-prevent fault, especially in vehicles that often use leaded gasoline. Even a new oxygen sensor can only function for a few thousand kilometers. 2. Carbon buildup: Poor engine combustion can lead to carbon deposits forming on the oxygen sensor surface, or oil and dust entering the sensor, obstructing or blocking external air from reaching the sensor's interior. This causes the oxygen sensor to output inaccurate signals, preventing the ECU from timely adjusting the air-fuel ratio. Symptoms of carbon buildup mainly include increased fuel consumption and significantly higher emission concentrations. 3. Ceramic breakage in the oxygen sensor: The ceramic in oxygen sensors is hard and brittle. Striking it with a hard object or washing it with strong airflow can easily cause it to break and fail. 4. Heater resistor wire burnout: For heated oxygen sensors, if the heater resistor wire burns out, it becomes difficult for the sensor to reach normal operating temperature, rendering it ineffective.
12
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.