···
Log in / Register

What is the formula for homemade tire shine?

4 Answers
LaHadley
07/29/25 8:53pm

Homemade tire shine formula consists of polyurethane emulsion, water, liquid wax, silicone oil, and emulsifier. Below are the detailed introductions of tire shine: 1. Function: The primary function is to restore the original new appearance of the tire, protect against UV damage, prevent rubber from aging, cracking, and fading, and effectively extend the tire's lifespan. It also helps remove oil stains and dirt from the tire, providing protection and preventing tire hardening. 2. Hazards: Tire shine does not harm the tire itself but can be somewhat harmful to the wheel hub due to its corrosive nature, which may corrode the hub. The shine that seeps into the steel rim might increase the gap between the tire and the hub, leading to air leakage and potential safety hazards.

Was this review help?
19
0
Share
LaneMarie
08/15/25 6:32pm

I used to mix my own tire shine solution frequently and found that a mix of olive oil and water works quite well, roughly in a 1:1 ratio, shaken well in a spray bottle. Before application, clean and dry the tire thoroughly, then spray the mixture on and spread it evenly with a sponge using circular motions. Wait for about ten minutes before wiping off any excess oil with a dry cloth. This method gives the tire a natural matte finish, but be careful not to spray it onto the brake discs. Reapplying weekly yields the best results, and it attracts less dust compared to chemical sprays. You can simply use the olive oil from your kitchen without needing to buy specialized products.

Was this review help?
8
1
Share
Expand All
DelCora
10/16/25 7:08am

You can make an eco-friendly tire shine at home with readily available materials: mix half a cup each of white vinegar and baking soda, then add two tablespoons of cornstarch to form a paste. Use an old toothbrush to apply the mixture to the tire sidewalls, let it sit for five minutes, and rinse it off. The white vinegar dissolves dirt, while the cornstarch fills in tiny rubber cracks, leaving the tires shiny black. It costs less than two yuan, lasts quite a while even in rainy weather, and most importantly, it has no strong odor and won’t harm plants in your yard.

Was this review help?
9
2
Share
Expand All
DeEmmett
11/29/25 7:54am

Dish soap and cornstarch make an ultra-affordable cleaner! Mix one spoon of dish soap with four spoons of water, then stir in two spoons of cornstarch until it forms a milky emulsion. Wet a sponge and apply it directly to the tires—dirt emulsifies and breaks down instantly, while the cornstarm leaves a reflective layer on the rubber. This $0.30 solution lasts half a year, with supermarket ingredients you can grab blindly. Post-cleaning, tires gain a glossy, hydrated shine. Opt for fragrance-free dish soap to avoid attracting ants.

Was this review help?
2
1
Share
Expand All
More Forum Discussions

How to Turn On Front and Rear Fog Lights?

Front and rear fog lights can be turned on as follows: 1. Lever-type fog lights: Rotate the lever upwards one notch to turn on the front fog lights, and rotate two notches to turn on both front and rear fog lights simultaneously. 2. Knob-type fog lights: Pull the knob out one position to turn on the front fog lights, and pull it out another position to turn on both front and rear fog lights at the same time. Additional information: 1. Purpose of fog lights: Installed at the front and rear of the vehicle, fog lights enhance visibility for the driver and other road users. 2. When to use fog lights: They must be turned on during heavy fog or rain when visibility is low to prevent rear-end collisions.
12
4
Share

Where is the fuse box located in the BMW 3 Series?

The BMW 3 Series has two fuse boxes, one located on the side of the trunk and the other in the engine compartment in front of the passenger seat. Below are the detailed specifications of the BMW 3 Series: 1. Body dimensions: The vehicle weighs 1465 kg, with length, width, and height measuring 4734mm, 1811mm, and 1455mm respectively. 2. Powertrain: The long-wheelbase version of the BMW 3 Series is equipped with the new B-series 2.0T engine, delivering 184 horsepower, the same as the current 320i/Li, but the tail badge has been changed to 325Li. 3. Transmission: It is paired with an 8-speed automatic transmission. Additionally, improvements in lightweight design, thermal energy management, and fuel efficiency optimization contribute to the vehicle's power output.
4
3
Share

Do You Need to Press the Brake to Shift Gears in an Automatic Transmission?

Automatic transmissions do not require pressing the brake to shift gears. Here is an introduction to the gears of an automatic transmission car: 1. All gears: The gears of an automatic transmission include P, R, N, D, 2 or S, L or 1. 2. Parking gear: P stands for Parking gear, also known as the Parking position. 3. Other gears: R stands for Reverse, N stands for Neutral, D stands for Drive, also known as the Driving gear. 4. Sport mode: S or 2 represents Sport mode. 5. Low gear: L or 1 stands for Low gear, also known as 1st gear. Here is additional information on driving an automatic transmission car: 1. General situation: When driving, unless there are special requirements, do not repeatedly move the gear lever between D, 3, 2, 1, etc. 2. Damage: When starting an automatic transmission car, ensure the gear is in P or N position, otherwise it may damage the transmission. 3. Reversing: When reversing an automatic transmission car, ensure the vehicle is completely stopped before shifting into R gear.
5
5
Share

What Causes Engine Shaking When Starting an Automatic Car?

Here are the reasons for engine shaking when starting an automatic car: 1. Throttle: A dirty throttle causes uneven airflow, leading to shaking. 2. Fuel system: Poor fuel flow results in inadequate fuel supply at low throttle, causing uneven cylinder operation and shaking. 3. Transmission: Abnormal transmission operation. 4. High-voltage wires: Broken or burnt high-voltage wires or spark plug failure can cause cylinders to misfire, leading to unstable engine operation and shaking. 5. Battery voltage: Whether the battery voltage is within the specified range. Below are additional details on related causes: 1. Cause: The most common reason for car shaking is a dirty throttle or excessive carbon buildup in the fuel injectors. 2. Engine carbon buildup: When there is excessive carbon buildup inside the engine, the gasoline sprayed by the cold-start injector is largely absorbed by the carbon deposits, resulting in an overly lean air-fuel mixture during cold starts and making it difficult to start.
8
5
Share

Which Turn Signal to Use When Exiting a Ramp?

When exiting a ramp, you should turn on the right turn signal. Below is an introduction about exiting a ramp: 1. Exiting a ramp: (1) When exiting a highway via a ramp, pay attention to the intersection warning signs, divert your vehicle from the main lane into the deceleration lane to slow down, and then enter the general road via the ramp. (2) When leaving the ramp, turn on the right turn signal. 2. Entering a ramp: (1) On the ramp, when entering the highway, you need to quickly increase your speed. However, do not exceed the speed limit indicated by the signs. Overtaking, making U-turns, stopping, and reversing are not allowed on the ramp. (2) After driving from the ramp into the highway acceleration lane, you may or may not turn on the left turn signal, quickly increase your speed to over 60 km/h, and carefully observe the traffic on the lane to choose the right moment to merge into the driving lane. Emergency braking or stopping in the acceleration lane is not allowed. When the driving lane is sparsely populated with vehicles, you can merge into the driving lane after normal driving; if vehicles on the highway are following closely, control your speed and merge into the driving lane only after all vehicles have passed.
15
1
Share

Is starting at 3000 RPM harmful to a CVT transmission?

Starting a CVT transmission at 3000 RPM can cause certain damage to the transmission and clutch plates, and it is not recommended to drive this way. There are three common types of automatic transmissions in automatic cars: dual-clutch transmissions, CVT transmissions, and AT transmissions. The specific details are as follows: 1. Dual-clutch transmission: (1) It connects to the engine via clutch plates. The structure of a dual-clutch transmission is similar to that of a manual transmission, except that it has an additional set of clutches and a shift control mechanism. (2) One set of clutches in a dual-clutch transmission controls the odd-numbered gears, while the other set controls the even-numbered gears. (3) Dual-clutch transmissions offer fast shifting speeds and relatively high transmission efficiency. 2. AT transmission: (1) It connects to the engine via a torque converter. (2) AT transmissions are the most mature and widely used automatic transmissions, featuring a relatively complex structure. (3) AT transmissions contain many planetary gears, which are responsible for gear shifting and torque conversion. 3. CVT transmission: (1) The internal structure is relatively simple, consisting of only two pulleys and a steel belt. (2) The steel belt in a CVT transmission can move along the pulleys, enabling gear shifting and torque conversion. (3) CVT transmissions provide smooth shifting and good reliability and durability.
7
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.