What is the fault when the car key light flashes?

1 Answers
StElisa
07/29/25 3:47pm
If the light keeps flashing when the engine is off, it is a normal phenomenon. However, if it continues to flash after getting into the car, it indicates a fault, usually due to the smart key being unrecognized or low battery. The following is a detailed introduction to the dashboard: 1. The dashboard is a high-definition panel or structural component installed with instruments and related devices. It can be divided into screen-type dashboard, frame-type dashboard, channel-type dashboard, and cabinet-type dashboard according to its form. 2. The dashboard includes an engine tachometer, maintenance indicator light, mileage meter, digital speed display, etc. There is also a door status indicator light on the dashboard, which is used to indicate whether the door is completely closed. When the door is not properly closed, the indicator light will illuminate to remind the owner. With the continuous development of technology, there are more and more indicator lights on the car dashboard. It is recommended to develop the habit of checking the dashboard before driving every day.
Was this review help?
14
2
Share
More Forum Discussions

How to Coordinate the Clutch and Throttle During Gear Up-shifting in Subject Three?

Subject Three gear up-shifting requires the following coordination between clutch and throttle: 1. Coordination between engine and clutch: Engine power is transmitted to the wheels through the clutch, with only about 10mm of travel reflected on the clutch pedal. Therefore, after depressing the clutch pedal and engaging the gear, when lifting the clutch pedal to the point where the clutch friction plates begin to make contact, pause briefly at this position while simultaneously applying throttle. Wait until the clutch plates are fully engaged before completely releasing the clutch pedal. 2. When shifting from a lower gear to a higher gear: Perform quick and agile movements—depress the clutch pedal while releasing the throttle pedal, immediately shift the gear lever to the neutral position, quickly lift and then depress the clutch pedal again while shifting the gear lever to the higher gear position. Lift the clutch pedal while applying throttle, pausing slightly when the clutch plates first make contact. Wait until they are fully engaged before completely releasing the clutch pedal.
10
3
Share

What is the issue with the Mercedes-Benz fault code P06DA00?

P06DA00 indicates a problem with the engine oil pump, typically an electrical circuit fault. Besides the engine oil pump malfunction, there are several other causes for the P06DA00 fault code, including air leaks in the vehicle's intake system, engine misfire, damaged fuel injectors, and ignition system failures. Here is an introduction to automotive fault codes: 1. Introduction One: Automotive fault codes are generated by the vehicle's ECU (Engine Control Unit) when a fault is detected. Each fault code corresponds to a different vehicle issue. When a fault occurs, specialized diagnostic tools can read these codes, greatly aiding mechanics in identifying the root cause of the problem. 2. Introduction Two: Sometimes, automotive fault codes may be falsely reported. In such cases, simply clearing the code is sufficient, and it does not affect the normal operation of the vehicle.
9
5
Share

How often should the air conditioning filter of the Octavia be replaced?

The official recommendation for the Octavia's air conditioning filter replacement is every 25,000 KM or 36 months. More information about the air conditioning filter is as follows: 1. The car air conditioning filter should be selected from a reputable brand that is suitable for your vehicle model and guarantees quality. The air conditioning filter is a filter installed in the car's air conditioning system that can absorb dust particles and protect the air conditioning cooling system; 2. The air conditioning filter should be cleaned monthly and replaced every 30,000 KM or 2 years. Regular cleaning of the air conditioning filter can extend its service life. When replacing the air conditioning filter, if possible, use a specialized cleaner to clean the blower and air ducts. Note that the air conditioning filter has a top and bottom side, with an upward arrow marked on the filter—make sure not to install it upside down.
5
3
Share

Where is the tire pressure reset button on the Roewe 360?

The tire pressure reset button for the Roewe 360 is located on the center console, marked with the TPMS button. The specific operation method for tire pressure reset is to press and hold the TPMS button when the tire pressure is normal. Below is additional information about the Roewe 360: 1. It is available in 7 models with two engine displacements, 1.5L and 1.4T, equipped with a 1.4T + 7-speed dual-clutch powertrain. 2. The Roewe 360 with the 1.5L engine comes in 4 models, divided into Elite and Luxury configurations, offering both manual and automatic transmission options. 3. The 1.4T engine is available in 3 models, with configurations ranging from high to low: Elite, Premium, and Flagship models.
19
2
Share

Is the power of the Bestune T77 sufficient for starting and climbing slopes?

The Bestune T77 is equipped with a hill descent control function, making its power sufficient for starting and climbing slopes. Below is extended information about the Bestune T77: 1. The Bestune T77's control configurations include ABS anti-lock braking, brake force distribution, brake assist, traction control, electronic stability control, hill start assist, hill descent control, and auto hold. 2. Safety features include front and side airbags, child seat anchors, tire pressure monitoring system, engine immobilizer, and seatbelt reminder. 3. The Bestune T77 is powered by a CA4GA12TD 1.2T direct-injection turbocharged engine across all models. Its maximum net power/speed is 100kW/5500rpm, and maximum net torque/speed is 204Nm/1600-4200rpm.
8
5
Share

What Causes the Jerking Sensation When Shifting Gears in an Automatic Transmission?

Automatic transmission jerking during gear shifts may be caused by clutch pressure leakage inside the transmission. Below are common causes and solutions: 1. Internal transmission clutch pressure leakage: Inspect clutch damage and perform repairs. 2. Blocked or poor transmission oil flow: Worn valve body, long overdue transmission fluid change leading to deterioration and reduced lubrication, excessively dirty transmission filter with poor filtration allowing wear particles to enter valve body. 3. Incorrect transmission fluid level: Verify whether transmission fluid meets standard level - both insufficient and excessive fluid can cause this issue. Vehicles with transmission dipsticks can check fluid level against standard markings when engine is running. 4. Solenoid valve damage: Sludge circulating in transmission fluid blocking oil passages in valve body may cause jerking, which over time leads to transmission overheating, harsh shifting, slippage and other transmission problems.
9
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.