What is the fault code for Kobelco Z010?

2 Answers
ChristianLee
09/04/25 3:09am
Z010 alarm indicates low common rail pressure, mainly caused by worn fuel injectors. It is recommended to replace the original filter element, regularly drain water and sediment from the fuel tank and water separator, and use high-quality diesel. This situation is related to diesel quality and daily fuel system maintenance. The Z010 alarm detects pressure change time in the injectors. Daily maintenance precautions are as follows: 1. Daily inspection: Daily inspection is an important part of ensuring the long-term effective operation of hydraulic excavators, especially for single operators. Daily inspections can effectively reduce maintenance costs. 2. Excavator bucket: Check whether the excavator bucket teeth are excessively worn. It is understood that wear on bucket teeth will significantly increase resistance during construction, seriously affecting work efficiency and accelerating wear on equipment components. 3. Control levers and cylinders: Check control levers and cylinders for cracks or oil leaks, inspect battery electrolyte, and avoid dropping below the low-voltage line.
Was this review help?
11
3
Share
EmmanuelDella
09/16/25 4:21am
You mentioned the Shinko Z010 fault code, which reminds me of my past experience in car repairs. Such fault codes are usually alarm signals detected by the vehicle's computer when there's an issue, such as a sensor malfunction or circuit abnormality. While Z010 might be specific to certain brands or models, most similar codes like P0100 indicate a mass airflow sensor fault, which can cause engine shaking or increased fuel consumption. I've seen cases where aged wiring, dust accumulation on sensors, or blown fuses triggered similar alarms. The key is to use an OBD scanner to read the specific meaning, as ignoring it could worsen the problem or even leave you stranded on the road. Always pay attention to dashboard warning lights while driving—if they illuminate, stop and check as soon as possible or seek professional diagnosis at a repair shop. This can save you a lot of trouble down the line.
Was this review help?
20
2
Share
Expand All
More Forum Discussions

How to adjust the mirrors on an Audi Q3?

Audi Q3 adjusts the mirrors by: locating the mirror knob on the door armrest, turning the knob to the left to the left mirror mark, then you can move the knob up, down, left, and right to adjust the angle of the left mirror. Similarly, you can adjust the angle of the right mirror. The 0 mark represents the idle position. When the knob is turned to the idle position, it can prevent all previous settings from being accidentally disrupted. The Audi Q3 has a length of 4481mm, width of 1848mm, height of 1616mm, a wheelbase of 2680mm, and a fuel tank capacity of 60l. It is equipped with a 1.4l turbocharged engine with a maximum power of 110 kilowatts, matched with a 7-speed dual-clutch transmission.
12
5
Share

How to check the tire pressure monitoring on Volkswagen Tiguan?

To check the tire pressure monitoring on the Volkswagen Tiguan, follow these steps: Select "Tire Pressure" in the onboard computer, and the values will be displayed on the central information screen of the instrument panel. The Volkswagen Tiguan has dimensions of 4506mm in length, 1809mm in width, and 1685mm in height, with a wheelbase of 2684mm and a fuel tank capacity of 63 liters. This vehicle is equipped with a 1.8T turbocharged engine, delivering a maximum horsepower of 160PS and a maximum power output of 118kW. It features front-engine, front-wheel drive configuration, with the maximum power achieved at 4500 to 6200 rpm, paired with a 6-speed automatic transmission.
7
2
Share

What current should be set for charging a car battery?

When charging a car battery, set the current between 14 to 15 volts. The battery is a crucial component in a car, functioning to store electrical energy. Without it, the car cannot operate properly. A car battery, also known as a storage battery, works by converting chemical energy into electrical energy. There are several types of car batteries: conventional batteries, dry-charged batteries, and maintenance-free batteries. Methods to restore a depleted car battery include: 1. Using a charger with a low current over an extended period to replenish the battery; 2. Finding a rescue vehicle and connecting the battery electrodes of both vehicles with charging cables to start the rescue vehicle for charging; 3. Increasing the voltage of the repair machine to over 10 volts for charging.
8
0
Share

What engine does the BYD Tang use?

BYD Tang uses a 2.0T engine with the model code BYD487ZQA. The engine can refer to both the power generation device and the entire machine including the power unit (such as gasoline engines, aircraft engines). Its types include internal combustion engines (such as gasoline engines), external combustion engines (such as Stirling engines, steam engines), gas turbines (used in racing cars), electric motors, etc. The BYD Tang is a 5-door, 7-seat midsize SUV with dimensions of 4870 mm in length, 1940 mm in width, and 1720 mm in height, and a wheelbase of 2820 mm. This vehicle is equipped with a 2.0T turbocharged engine with a maximum power output of 141 kW, paired with a 6-speed automatic transmission.
1
0
Share

How to Use the Auto Hold Function in a Car?

To use the auto hold function in a car: When waiting at a traffic light or needing to stop briefly, press the auto hold button on the vehicle to activate it. At this time, you do not need to press the brake pedal or pull the handbrake, as the system will automatically brake the vehicle. The system will automatically release when the accelerator pedal is pressed. Auto hold refers to an automatic braking function. Once activated, it simplifies operations by eliminating the need to use the handbrake or electronic handbrake. For automatic transmission models, it also avoids frequent switching between D to N or D to P. This function relies on an intelligent braking system, and only vehicles equipped with brake control systems like ESP can implement the auto hold function.
14
0
Share

Is the new BMW X4 a three-cylinder?

The new BMW X4 is not a three-cylinder. The entire lineup of the new BMW X4 uses a 2.0-liter turbocharged four-cylinder engine. The vehicle is equipped with two versions of this engine: a low-power version and a high-power version of the 2.0-liter turbocharged engine. The new BMW X4 is a mid-size SUV with dimensions of 4763mm in length, 1926mm in width, and 1632mm in height, and a wheelbase of 2864mm. The front suspension of this vehicle is a double-joint spring strut front axle, and the rear suspension is a five-link rear suspension. It is powered by a 2.0L turbocharged engine with a maximum horsepower of 184ps, a maximum power of 135kw, and a maximum torque of 290nm.
18
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.