What is the fastest speed record at the Isle of Man TT?

What Causes Difficulty in Cold Starts but Normal Operation When Warm?

The reasons for difficulty in cold starts but normal operation when warm are as follows: 1. Poor fuel quality. Low-quality fuel often has poor volatility, especially during cold starts in winter when the engine block temperature is low, making fuel atomization difficult. This results in insufficient mixing of fuel and air in the combustion chamber, leading to starting difficulties or even failure to start. 2. Carbon deposits. The lower the temperature, the more fuel is required for a cold start, and the presence of carbon deposits significantly affects the success of the cold start. Carbon deposits in various parts of the engine negatively impact its normal operation. 3. Untimely spark plug replacement. Cold starts require higher ignition energy, and after a certain mileage, the electrode gap of spark plugs widens. If this exceeds the standard, the spark energy generated will weaken considerably, failing to properly ignite the air-fuel mixture in the cylinder, making it naturally difficult to start.

10

1

Share

What are the tips for curve driving in Subject 2 of the driving test?

Driving license Subject 2 curve driving skills are as follows: 1. When the left front corner coincides with the right sideline, turn the steering wheel one circle to the left. After turning one circle, keep the front corner of the car aligned with the right sideline. If there is any deviation, correct it by adjusting the steering wheel, with the correction range within half a circle. When approaching the junction of the right curve, straighten the steering wheel. At this point, the left front corner of the car body will nearly coincide with the left sideline. After straightening the steering wheel, proceed forward. 2. As the car moves forward, the AB segment curve will gradually move toward the left side of the engine hood. Slowly turn the steering wheel to the left to keep the left ridge of the engine hood aligned with the AB segment curve. 3. Enter the curve test with the car head aligned to the right yellow line. The rear wheels may press the line, so enter the curve driving section at a low speed.

13

3

Share

What does the Buick Excelle GT mean?

Buick Excelle GT is a sedan. More information about it is as follows: 1. The Excelle XT is a hatchback, while the GT is a sedan. 2. The Excelle GT is a sedan meticulously crafted for individuals who pursue quality in life, offering a perfect driving experience that surpasses expectations. With globally leading technology and automotive craftsmanship, it truly integrates performance with comfort. Known as the "little LaCrosse," the Buick Excelle GT sets a new standard in the mid-to-high-end car market with its premium sedan capabilities. Leveraging advanced global technology and manufacturing techniques, it redefines the conventional definition of mid-size cars by seamlessly blending performance and comfort. It caters to the contemporary values of the new generation of mainstream achievers who seek perfection, aiming to provide them with an all-around upgraded "premium" sensory experience and helping them expand their horizons in life as they strive for continuous progress.

8

5

Share

What is the adjustment method for the brake master cylinder push rod?

Locate the push rod of the cylinder, which has two screws on it. Adjust the push rod travel by tightening or loosening these screws. Below is a related introduction to the brake master cylinder: 1. The brake master cylinder, also known as the "brake main cylinder" or "brake master cylinder," is a key component of the vehicle's braking system. In oil-brake systems, the master cylinder has a reservoir for brake fluid at the top, while the lower part contains a cylinder with a piston and inlet/outlet ports. 2. Its working principle is as follows: When the brake pedal is pressed, the piston inside the cylinder is pushed by the force from the pedal, and the push rod transmits this force to pressurize the brake fluid, which is then sent to each wheel's brake slave cylinder to generate braking force. When the brake pedal is released, the outlet port of the master cylinder closes, and the inlet port opens, allowing the brake fluid to flow back from the slave cylinders to the master cylinder, returning to its original state.

6

0

Share

What is the method for measuring cylinder pressure?

Cylinder compression pressure measurement methods are as follows: 1. Using a cylinder pressure gauge. The measurement steps are as follows: (1) Ensure the engine operates normally until the coolant temperature reaches above 75°C. (2) Insert the rubber adapter of the cylinder pressure gauge into the spark plug hole of the cylinder being tested, ensuring it is properly aligned and tightly secured. (3) Fully open the throttle and choke valves, then use the starter to rotate the crankshaft for 3-5 seconds (no fewer than four compression strokes). Stop rotating once the pressure gauge pointer indicates and maintains the maximum pressure. (4) Remove the cylinder pressure gauge, record the reading, and press the one-way valve to reset the pressure gauge pointer to zero. Measure each cylinder in sequence using the above method, with each cylinder measured at least twice. 2. Using a cylinder pressure tester. (1) Measure with a pressure sensor-type cylinder pressure tester. (2) Measure with a starter current or starter voltage drop-type cylinder pressure tester. (3) Measure with an inductive discharge-type cylinder pressure tester.

15

5

Share

Should You Apply Film to a Car Sunroof?

Generally, it is not recommended to apply film to a car sunroof. Here are the reasons why: 1. The sunroof glass usually already has UV protection and heat insulation functions. Applying film again would not only cause a certain degree of resource waste but also affect the overall quality of the vehicle. 2. After applying film to the sunroof, the overall thickness of the glass increases. If the installation is not done properly, it may lead to difficulties in opening and closing the sunroof. However, during hot summers, if the car is parked outdoors for a while, the sunroof area, being a weak spot for heat insulation on the roof, can cause the interior temperature to rise. If the decorative panel under the sunroof is opened, more heat will enter the car through the sunroof. Therefore, for large panoramic sunroofs, applying film may be considered depending on the regional climate and season. But not all panoramic sunroofs are suitable for film application. If the sunroof is made of colored heat-absorbing glass, dark-colored film should not be applied.

12

0

Share

What is the fastest speed record at the Isle of Man TT?

What Causes Difficulty in Cold Starts but Normal Operation When Warm?

What are the tips for curve driving in Subject 2 of the driving test?

What does the Buick Excelle GT mean?

What is the adjustment method for the brake master cylinder push rod?

What is the method for measuring cylinder pressure?

Should You Apply Film to a Car Sunroof?

Is Haval a Joint Venture or Domestic Brand?

What are the contents of daily car maintenance?

How to Display the Car's Driving Range?

Should the car DUAL button generally be turned on?