What is the engine model of the Enclave?

1 Answers
LaAriana
07/29/25 8:36pm
The engine model of the Enclave is LSY. The Enclave is equipped with a 2.0-liter turbocharged engine across the entire lineup, delivering a maximum power of 237 horsepower and a maximum torque of 350 Nm. This engine can output its maximum power at 5,000 rpm and its maximum torque between 1,500 and 4,000 rpm. The Enclave is a mid-to-large-sized SUV with dimensions of 4,981 mm in length, 1,953 mm in width, and 1,732 mm in height, and a wheelbase of 2,863 mm. The exterior design of the Enclave follows the family-style design concept, featuring a large-sized winged front grille complemented by chrome trim around the edges, giving the front face a very youthful appearance.
Was this review help?
17
5
Share
More Forum Discussions

How to Replace the Battery in a Mercedes-Benz E200 Supercharged Edition Key?

The method to replace the battery in a Mercedes-Benz E200 Supercharged Edition key is as follows: First, push the marked switch upwards to remove the mechanical key, then open the key casing and pry out the old battery before inserting the new one. The Mercedes-Benz E200 is a 4-door, 5-seater mid-to-large-sized sedan with dimensions of 4925mm in length, 1860mm in width, and 1470mm in height, featuring a wheelbase of 2939mm and a rear-wheel-drive layout. In terms of exterior design, the Mercedes-Benz E200 adopts a sporty front bumper with air intakes featuring black diamond grilles, dual chrome trim elements on the sides, and visible dual exhaust tailpipe trims, presenting a stylish and dynamic appearance.
13
0
Share

How to Determine if a Car Blower Resistor is Good or Bad?

Turn on the blower switch inside the cabin and check the operation of the electric blower, ensuring it runs normally without any abnormal noises. Inspect the blower fan blades for any damage or detachment. Check the air delivery rubber hose for aging and wear; replace if damaged. Turn on the heater switch and blower switch to verify that the heating and ventilation equipment meets the required conditions. If not, adjustments or repairs should be made.
14
2
Share

Why does the car fail to start after washing?

The reasons why the car fails to start after washing are: 1. The car gets damp; 2. After washing, the parts from the distributor to the high-voltage wire to the spark plug get damp, preventing high-voltage electricity from reaching the spark plug. Solution: Open the distributor cover of the car, dry the damp parts with a dry towel or use a hair dryer to blow them dry. The correct method to start the car: Before ignition, confirm that the gear is in neutral, depress the clutch, turn the key to the ACC position, wait for about 3 to 5 seconds for the car's circuit to complete self-inspection, and then turn it to the START position for ignition. After successful ignition, release the key in time to let it return to the ON position, so that the gear of the starter motor and the flywheel of the engine will not disengage, thus avoiding damage to the starter motor due to excessive flywheel speed.
4
3
Share

What to Do When the Car Horn Sounds Muffled After Going Through Water?

First, remove the horn, which can be done by yourself or at a professional repair facility. After removing the horn, clear any accumulated water inside and let it dry. If the horn returns to normal after this treatment, it can continue to be used. However, if the horn still sounds muffled after the treatment, the damaged horn will need to be replaced.
18
4
Share

How to Fix a Dented Car Trunk by Yourself?

First, insert the glue stick into the glue gun and heat it for a few minutes, then slowly apply it from left to right onto the suction cup. Attach the suction cup to the stress point of the larger dent, then connect the "T"-shaped tool to the head of the suction cup. Pull the suction cup out with even force, and the dent will gradually recover.
7
2
Share

What is the best solution for rear drum brake lock-up in cars?

Floor the accelerator pedal - as long as the rear wheels start moving, the problem will be resolved. Use a hammer or similar tool to strike the brake drum a couple of times to separate the contact surface between the brake drum and brake shoes. After washing the car or when the brake drums get wet from rain, avoid parking immediately. Drive for a while and apply the brakes several times to allow the moisture inside to evaporate.
17
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.