What is the emission standard for the 2009 Cruze?

1 Answers
LeJaxson
07/29/25 10:11pm
The 2009 Cruze meets the National IV emission standard. Here are the methods to check the Cruze's emission standard: 1. The most obvious method is to look at the front windshield of the car, where the vehicle emission standard number is clearly marked; 2. You can also check the vehicle's emission standard on the National Motor Vehicle Environmental Protection Label Query website, but you need to set the location to where the vehicle is registered before querying; 3. Another way is to bring your valid documents, such as the vehicle registration certificate, to the local vehicle management office and inquire at the environmental protection window; 4. Additionally, the emission standard can be found on the vehicle's factory certificate.
Was this review help?
2
5
Share
More Forum Discussions

Where does the Cangshuo Expressway run from and to?

Cangshuo Expressway connects Cangwu District in Wuzhou City, Guangxi Province to Shuolong Town in Daxin County, Chongzuo City, Guangxi Province. It is a provincial-level expressway, with most sections currently under construction while some segments have already been opened to traffic. The traffic violation monitoring points from kilometer 7 to kilometer 21 of Cangshuo Expressway are located in Chaozhou City, Guangdong Province. If violations occur, they should be handled at the local vehicle management office in Chaozhou City, Guangdong Province. Expressways are multi-lane roads exclusively designed for directional and lane-segregated vehicle traffic with full access control. The average annual daily traffic volume for expressways should ideally exceed 15,000 passenger car units, with design speeds ranging from 80 to 120 kilometers per hour.
1
2
Share

Is there an overtime fee for private cars on highways?

Private cars do not incur overtime fees on highways; they are charged based on mileage. The highway overtime fee refers to a penalty measure implemented to combat toll evasion by drivers, applicable when a vehicle spends more than 24 hours within the highway network or more than 12 hours on the same highway route. The concept of time limits on highways is calculated by dividing the distance between highway entry and exit points by the minimum speed limit, primarily aimed at improving road usage efficiency and preventing toll evasion. If a vehicle suddenly breaks down during the journey, relevant maintenance records should be retained. In cases where repairs are done without third-party verification, a short video can be recorded during the repair process, ensuring to capture prominent roadside signs. This way, even without third-party documentation, one can prove their innocence when exiting the highway.
7
5
Share

How to Read the Oil Dipstick?

Turn off the engine and wait for 5 minutes before opening the engine compartment. Pull out the yellow cap to extract the oil dipstick, wipe it clean, reinsert it, and then pull it out again to see the oil level mark left on the dipstick. Below are the detailed steps for changing the engine oil: 1. Warm up the car before oil change: Start the vehicle and let the coolant temperature reach normal operating levels, then turn off the engine. The purpose of warming up the car is to allow the oil to flow freely and carry out impurities. Use a jack to lift the vehicle and engage the handbrake. 2. Drain the old oil: Use the onboard tools to loosen the oil pan drain plug and let the oil flow out. Ensure to collect the old oil in a container to avoid environmental contamination. Once the oil is fully drained, reinstall the drain plug, being careful not to overtighten it to prevent damage to the oil pan. 3. Install the new oil filter: Use an oil filter wrench to loosen the old filter. Apply new oil to the rubber seal of the new filter, then manually install it and tighten it with the tool. 4. Refill with new oil: Pour the new oil into the oil filler port, using a funnel if necessary. After refilling, check for any leaks. If no abnormalities are found, remove the jack and lower the vehicle. Use the oil dipstick to confirm the oil level, restart the vehicle, and check if any warning lights are illuminated.
17
1
Share

What are the three modes of the Audi Q5L air conditioning system?

The three modes of the Audi Q5L air conditioning system are Auto Mode, Cooling Mode, and Heating Mode. Below is a partial introduction to car air conditioning systems: 1. Automatic Air Conditioning: The electronic control unit will operate the air conditioning system automatically based on the settings made by the driver or passengers via buttons on the air conditioning display control panel. It adjusts the air supply temperature and speed in real-time according to signals from various sensors to maintain the optimal air environment inside the vehicle. 2. Traditional Air Conditioning: This is manually controlled. There is a temperature adjustment knob on the air conditioning control panel, and rotating it changes the set temperature.
11
5
Share

How to Stop a Constantly Ringing Car Alarm?

To stop a constantly ringing car alarm, you can reduce the sensitivity of the anti-theft device to a level where kicking the tire does not trigger the alarm. The anti-theft control box is usually installed under the dashboard. After opening it, you will see a screw knob that can be adjusted to change the sensitivity. Below are some related explanations: 1. Overly Sensitive Anti-theft Device: The constant ringing of the car alarm is often due to the anti-theft device being too sensitive, causing it to trigger even with slight vibrations. To resolve this, first locate the main unit of the anti-theft device, which is typically found under the steering wheel or behind the A-pillar trim. Then, slightly adjust the sensitivity knob. However, avoid setting it too low, as this would significantly reduce the car's anti-theft effectiveness. 2. Faulty Anti-theft Device Wiring: Another possible cause is faulty wiring in the main unit of the anti-theft device, which requires prompt inspection, repair, or replacement.
16
3
Share

What to Do When the Car Tire Pressure Monitoring Light Comes On?

The methods to handle when the tire pressure warning light comes on are: 1. First, pull over to the side of the road and check the tire pressure of all four tires. If no obvious loss of air is visible, you can reset the tire pressure system after getting back in the car to turn off the warning light; 2. If the tire pressure warning light comes on again, it indicates that there is indeed a problem with the tire pressure of one of the tires, and it needs to be inspected and repaired promptly. Reasons why the car tire pressure warning light comes on: 1. A tire puncture; 2. Excessive tire pressure; 3. Driving with low tire pressure for too long; 4. Malfunction of the tire pressure sensor; 5. Low tire pressure due to prolonged lack of inflation. Installing a tire pressure monitoring alarm in the car can prevent accidents caused by abnormal tire pressure.
8
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.