What is the displacement of the Mustang?

1 Answers
DanteAnn
07/25/25 3:50pm
The Mustang has a displacement of 2.3L, equipped with a turbocharged engine. It delivers a maximum horsepower of 299ps, a maximum power output of 220kw at 5600rpm, and a maximum torque of 434nm at 3000rpm. It is paired with a 10-speed automatic transmission. The Mustang's body dimensions are: length 4794mm, width 1916mm, height 1373mm, with a wheelbase of 2720mm. The minimum ground clearance is 125mm, the vehicle weight is 1702kg, and the fuel tank capacity is 58.9l.
Was this review help?
6
1
Share
More Forum Discussions

What are the steps for removing the headliner of an 8th-generation Accord?

Steps for removing the headliner of an 8th-generation Accord: First, remove the three clips at the rear end of the headliner, then detach the C-pillar trim covers, followed by the four grab handles. Next, remove the sun visors, and finally, detach the B-pillar trim covers near the seat belts. Below is some related information: 1. The car headliner is an important part of the vehicle's interior. It serves functions such as decoration, sound absorption, and heat insulation. In an era increasingly focused on high performance, environmental friendliness, and lightweight design, the interior headliner has become a significant factor in car selection, leading to higher demands on automotive interior components. 2. The primary material of the car headliner is polyurethane foam, which offers advantages such as lightweight, heat insulation, and excellent elasticity.
9
1
Share

What is Engine Compression Ratio?

The ratio of the maximum volume of the cylinder at bottom dead center to the minimum volume at top dead center is the compression ratio. Below is an introduction to compression ratio: 1. Compression ratio refers to the degree to which the engine's air-fuel mixture is compressed. It is expressed as the ratio of the total cylinder volume before compression to the cylinder volume after compression. 2. Compression ratio is closely related to engine performance. The higher the compression ratio, the greater the engine's power. (V swept volume by piston + V combustion chamber volume) / V combustion chamber volume. 3. An engine with a compression ratio of 10 compresses the combustible mixture to 1/10 of its original volume. An excessively high compression ratio can reduce stability and shorten engine lifespan.
14
3
Share

How to Open the Front Hood of a Jinbei Vehicle?

Jinbei F50 hood opening method: Locate the hood release button on the driver's side leg area, then pull the button upward. Below is relevant information about the Jinbei F50: 1. Exterior design features a dignified and generous front fascia with a dual-slat chrome grille, LED daytime running lights, and electrically adjustable mirrors with integrated turn signals. 2. Dimensions measure 4745/1810/1845mm (L/W/H) with a 2860mm wheelbase. The vehicle adopts a "2+2+3" 7-seat layout similar to premium MPVs, prioritizing daily convenience and practicality. 3. The interior combines black and brown color schemes, featuring a simple three-spoke steering wheel and dual circular instrument cluster. IKEA-inspired models come equipped with an 8-inch touchscreen on the center console.
11
4
Share

Can I Switch from 98 Octane to 95 Octane Gasoline?

You can switch from 98 octane to 95 octane gasoline. Here are the reasons why it's acceptable to use 95 octane after running out of 98 octane: 1. Avoid mixing different octane grades of gasoline. If you previously used 98 octane gasoline, you should continue using 98 octane for your next refuel. In special circumstances, using 95 octane once won't cause major issues, but prolonged use may lead to engine knocking, increased carbon deposits, and higher fuel consumption. 2. Similarly, if you've been using 95 octane gasoline, adding 98 octane once or twice won't have significant impact, but long-term mixing should be avoided. If you want to change gasoline grades, it's best to wait until the fuel gauge light comes on before refueling with the new grade, or directly drain the remaining fuel before switching. Never mix different octane grades directly.
13
0
Share

Where is the oil dipstick for the BMW X1?

BMW vehicles use a different type of oil dipstick compared to other models, employing an electronic system for recording. BMW's electronic system records and reflects the condition and quantity of engine oil to the driver through this system. Owners can schedule maintenance at 4S dealerships based on the intervals prompted by the system or the recommendations from the dealer. Below is an introduction to the related content: 1. The after-sales maintenance standards implemented by BMW differ from those of other car brands, as there is no fixed maintenance interval. The official recommendation is to perform maintenance based on the prompts from the vehicle's system, known as the CBS (Condition Based Service) system, which provides alerts according to the actual wear and tear of the vehicle. 2. The first maintenance interval for BMW vehicles is between 10,000 to 12,000 kilometers. Depending on the driving conditions of the car, the CBS system may prompt different maintenance intervals.
8
0
Share

How to Clear the Maintenance Reminder on CS75?

Changan CS75 maintenance reminder clearing steps: 1. First, turn the car key to the ON position (full vehicle power-on state - turn key twice or press start button twice for keyless systems). 2. Then press the selection button on the steering wheel; hold the reset button for about 5 seconds (keep the reset button pressed continuously). 3. Turn off the power (while still holding the reset button), then turn the vehicle power back on to clear the maintenance reminder. Below is relevant information about vehicle maintenance: 1. Modern vehicle maintenance primarily includes engine systems, transmission systems, air conditioning systems, cooling systems, fuel systems, power steering systems, etc. 2. The purpose of vehicle maintenance is to maintain clean appearance, normal technical conditions, eliminate potential issues, prevent faults, slow deterioration processes, and extend service life. Routine maintenance refers to daily checks performed before driving, during operation, and after parking, which are the driver's responsibility. The main tasks involve cleaning, replenishment, and safety inspections - these are essential regular tasks to maintain normal vehicle operation.
20
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.