What is the difference between Volvo S90 B5 and T5?

What are the restrictions for out-of-town license plates in Shanghai?

Small passenger cars with license plates issued by other provinces or cities are prohibited from driving, including those with temporary license plates, unoccupied taxis, and cars driven by drivers in their probationary period (except on Saturdays, Sundays, and national holidays). The restricted hours for out-of-town license plates are from Monday to Friday, 7:00 AM–10:00 AM and 3:00 PM–8:00 PM. There are no restrictions on Saturdays, Sundays, or national holidays. Additional information: 1. Check tire surfaces before driving: Tire blowouts at high speeds are the most frequent and dangerous cause of traffic accidents. Therefore, before driving, be sure to inspect the wear on the tire surface, checking for bulges, cracks, or damage caused by sharp objects. If such issues exist, repair or maintenance should be performed before driving. 2. Replace problematic tires: If possible, remove the tires to inspect the inner side for damage, as hidden internal damage is often the main cause of accidents. If there’s no time for a thorough tire inspection and replacement, at least move problematic tires to the rear wheels to minimize the risk of accidents.

20

1

Share

Can I travel without carrying a driver's license now that I have an electronic one?

With an electronic driver's license, you can travel without carrying a physical one, but this doesn't apply universally, as the electronic driver's license is currently only being piloted in certain cities and has not been implemented nationwide. In cities where the electronic driver's license has been implemented, you naturally don't need to carry a paper version, which is indeed good news for forgetful car owners. Relevant information about the driver's license is as follows: 1. Introduction: The People's Republic of China Motor Vehicle Driver's License, referred to as the driver's license or 'driving license,' is a certificate required by law for motor vehicle drivers in China. 2. Examination Content: The test subjects include traffic regulations and related knowledge, field driving, and road driving (including safe and civilized driving), totaling three items.

9

2

Share

Do You Need to Press the Brake When Shifting to S Gear?

Automatic transmission does not require pressing the brake when shifting to S gear. The usage of S gear includes: during short-distance competitive races; when driving uphill, overtaking, or on rough roads; and when stronger traction is needed. Below are some tips on shifting gears: 1. Upshifting Techniques: Before upshifting, ensure the road ahead is clear. The throttle and clutch operate like a seesaw—do not press them simultaneously. Shift gently; generally, shifting up to fourth gear is sufficient, and fifth gear can be used if conditions allow. Upshifting must be done one gear at a time—skipping gears is not recommended. 2. Downshifting Techniques: To downshift, first reduce speed; to reduce speed, first apply the brakes. There is no need to downshift to first gear when stopping—stop in the current gear. Always start in first gear, but stopping does not require downshifting. For turns, use second gear; for U-turns, use first gear; for traffic lights, use third gear; and for pedestrian crossings, pass at around 30 km/h in third gear.

10

1

Share

What is the measurement method for a two-wire crankshaft position sensor?

The measurement method for a two-wire crankshaft position sensor is as follows: 1. The engine speed signal comes from the crankshaft position sensor. If the sensor does not output a signal, the engine tachometer will not move. 2. Connect the two probes of a multimeter to the two signal wires of the crankshaft position sensor. Set the multimeter to the 20V range at idle speed. A higher measured voltage indicates a higher engine speed. 3. Adjust the oscilloscope voltage to 14V and the time to 10ms, then start the vehicle to observe the AC signal waveform. 4. Use a diagnostic scanner to read the engine speed data stream. The functions of the crankshaft position sensor include: 1. Detecting engine speed; 2. Detecting the top dead center position of the pistons; 3. Detecting and controlling the top dead center signals for each cylinder's ignition.

20

3

Share

What Are the Reasons Why the Truck's Air Pressure Cannot Be Built Up?

Truck's air pressure cannot be built up possibly due to the poor quality of the air pump, which results in insufficient pressure, making the inflation process very slow and laborious. It could also be caused by large cracks in the truck's wheels, leading to air leakage while inflating, making it impossible to build up pressure. If no solution is found, it is advisable to visit a repair shop. Below are factors to consider when adjusting tire pressure: 1. Seasonal factors: In winter, it is recommended to slightly increase the tire pressure by about 0.2bar based on the standard tire pressure. In summer, follow the lower limit of the standard tire pressure, and for vehicles parked outdoors, the pressure can generally be about 0.1bar lower than the standard to avoid tire blowouts due to high temperatures. 2. Road conditions: On roads with significant bumps, it is advisable to slightly reduce the tire pressure by 0.1-0.2bar from the standard. For roads with minor bumps, this can be ignored. For long-distance high-speed driving, the tire pressure should not be too low; it is recommended to slightly increase the pressure by about 0.2bar from the lower limit of the standard tire pressure.

18

5

Share

What are the symptoms of a faulty air conditioning pressure switch?

The symptoms of a faulty car air conditioning pressure switch are: poor contact of the contacts or abnormal operation of the pressure switch, which can cause the compressor to not work or fail to provide normal pressure protection. The classifications of pressure switches are: 1. Car air conditioning low-pressure switch: The low-pressure switch is installed on the high-pressure pipeline of the refrigeration system. A refrigerant leak in the system can lead to insufficient refrigerant, causing the compressor's vacuum level to rise, ultimately resulting in compressor burnout due to lack of refrigerant. 2. Car air conditioning high-pressure switch: The high-pressure switch is installed on the pipeline at the condenser inlet. It is used to regulate the speed of the fan motor, keeping the condenser pressure within a certain range. 3. Car air conditioning dual-temperature switch: The dual-temperature switch is located near the condenser. The condenser fan motor is controlled by both the high-pressure switch and the engine coolant dual-temperature switch. When the coolant temperature is below 93°C and the air conditioning compressor is not activated, the cooling fan does not operate. 4. Car air conditioning three-stage pressure switch: The three-stage pressure switch in the car air conditioning refrigeration system is installed on the pipeline from the compressor to the condenser. The three-stage pressure switch has three pressure values. When the pressure is below 0.22 MPa or above 3.2 MPa, the compressor's electromagnetic clutch disengages.

11

4

Share

What is the difference between Volvo S90 B5 and T5?

What are the restrictions for out-of-town license plates in Shanghai?

Can I travel without carrying a driver's license now that I have an electronic one?

Do You Need to Press the Brake When Shifting to S Gear?

What is the measurement method for a two-wire crankshaft position sensor?

What Are the Reasons Why the Truck's Air Pressure Cannot Be Built Up?

What are the symptoms of a faulty air conditioning pressure switch?

Can Fake Driver's Licenses Be Detected?

What should I do if my ETC device is lost?

What are the gear and speed standards for Subject 3?

What is a China 5 Vehicle?