What is the difference between Volvo's blue logo and black logo?

1 Answers
KingstonAnn
07/29/25 3:24pm
Volvo's blue logo and black logo differ in the following aspects: 1. Color: The blue logo primarily features blue, while the black logo is dominated by black. 2. Arrow angle: The arrow in the blue logo forms a certain angle with the diagonal stripe representing the seatbelt, whereas in the black logo, the arrow overlaps with the stripe. 3. Letter placement: In the blue logo, the 'VOLVO' letters are positioned above the iron element symbol, while in the black logo, they are placed inside the circle of the iron element. Taking the 2021 Volvo S90 B5 Momentum Luxury Edition as an example, this model has the following dimensions: length 5090 mm, width 1879 mm, height 1450 mm, with a wheelbase of 3061 mm. It is equipped with a 2.0T inline 4-cylinder turbocharged engine, delivering a maximum horsepower of 250 hp and a maximum power output of 184 kW.
Was this review help?
5
0
Share
More Forum Discussions

What does 6-speed Tiptronic mean?

6-speed Tiptronic refers to a transmission that combines a 6-speed manual and automatic gearbox, which is a type of automatic transmission. It can reduce the impact of manual shifting on the car's drivetrain, prolong the service life of the car, improve ride comfort, and allow the selection of appropriate gears based on road conditions. The gears of a 6-speed Tiptronic transmission are as follows: 1. P (Park) is the parking gear; 2. R (Reverse) is the reverse gear; 3. N (Neutral) is the neutral gear; 4. D (Drive) is the forward gear; 5. S (Sport) is the sport mode; 6. M (+/-) is the manual mode, allowing manual gear shifting.
4
1
Share

What does it mean when the set light on the car is on?

When the set light on the car is on, it indicates abnormal tire pressure, and the tire pressure needs to be checked promptly. Its function is to adjust the tire pressure to the standard level. Press and hold the set button for three seconds while observing the speedometer. After hearing a beep, the tire pressure monitoring value will be calibrated accordingly. When there is abnormal tire pressure, a warning indicator will appear on the dashboard. Common knowledge for checking tire pressure safety: 1. Observe the tire condition before driving; 2. Pay attention to the friction sound between the tires and the ground while driving; 3. Be mindful of the cushioning force when driving on bumpy roads; 4. Regularly check and replenish the tire pressure; 5. Regularly clean particles and dirt from the tire surface.
8
0
Share

What are the reasons why the battery of Wuling Zhiguang cannot be charged?

Wuling Zhiguang's battery cannot be charged due to reasons such as dried-up electrolyte in the battery, broken plates, or short-circuited plates. The most common and primary reason is plate sulfation, which obstructs the normal flow of electrons, leading to reduced battery capacity, inability to function properly, and gradual aging. If a battery is left unused for a long time or is chronically undercharged, plate sulfation can occur. For batteries that have been in use for more than 3 years, it is recommended to replace them with a new one. For batteries with shorter usage periods that have experienced mild sulfation due to short-term excessive discharge, a low-current, long-duration charging method can be used for recovery. However, the battery capacity can only be restored to about 80% of its rated capacity. There are several main reasons for the early failure of vehicle batteries: Deep discharge: When the vehicle is parked but the lighting or other electronic devices remain on, the battery continues to discharge. Prolonged discharge significantly reduces the battery's lifespan. Overcharging or engine overheating causing electrolyte evaporation: Since the electrolyte is composed of specialized sulfuric acid and distilled water in a specific ratio, engine overheating will accelerate the evaporation of distilled water, disrupting the balance between sulfuric acid and distilled water in the electrolyte and shortening the battery's lifespan. Loose alternator belt leading to insufficient charging: The vehicle's alternator supplies power to the electronic devices and charges the battery while the vehicle is in use (except during idle). If the alternator belt is too loose, it will result in insufficient charging of the battery, affecting its normal operation.
5
4
Share

What is the CAN Bus Repair Method?

CAN bus repair methods are: 1. Check specific fault symptoms; 2. Use relevant diagnostic instruments for diagnosis; 3. Formulate relevant maintenance plans; 4. Locate specific fault locations and causes; 5. Combine corresponding detection methods and measurement results to find the fault point and eliminate the fault. Symptoms of CAN bus failure: 1. Abnormal dashboard display; 2. Vehicle cannot start; 3. Decreased power performance; 4. Unable to turn off after starting; 5. Some electronic control system functions fail. Characteristics of CAN bus: 1. High performance; 2. High integration; 3. Controllability; 4. Verification and error correction; 5. Repair capability; 6. Intelligence; 7. Security.
5
2
Share

How to Remove the Blower Motor in a BMW 525?

To remove the air conditioning blower motor in a BMW 525, first, you need to take off the glove box on the passenger side. Then locate the screws underneath. After removing them, you can take off the air duct of the BMW 525. Next, find the wiring harness connector connected to the BMW 525's air conditioning system and unplug it. Then, also disconnect the plug on the BMW 525's air conditioning blower motor. Finally, remove the car's air conditioning blower motor.
1
2
Share

What is Gasoline Additive?

Gasoline additive, short for fuel additive, is designed to compensate for the inherent quality issues of fuel and the limitations in automotive mechanical manufacturing. It enables gasoline engines to overcome the cold shock effect and crevice effect, serving to remove carbon deposits from intake valves and fuel injectors. The composition and functions of gasoline additives can be categorized into: 1. Maintenance-type fuel additives: They envelop carbon deposit particles formed through oxidative condensation reactions at high temperatures, preventing them from growing larger; 2. Cleaning-type fuel additives: When carbon deposits accumulate on the surfaces of fuel injectors and intake valves, cleaning-type additives utilize surfactants to penetrate the pores of carbon deposits, disrupt their structure, segment and envelop the carbon particles, and dissolve them for expulsion through exhaust emissions.
14
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.