Browse

Antiques Collectibles Apparel Baby Kids Items Books， Movies And Music Electronics Free Stuff Garden Outdoor Health Beauty Home Goods Home Improvement Supplies Musical Instruments Office Supplies Pet Supplies Sporting Goods Ticket Toys Games Transportation Others

Used Cars New Cars Others

Business Crafts Design And Web Events Home Improvement Legal Lessons Personal Pets Photography Repair And Technical Support Wellness Writing， Translation， And Transcription Others

Activities & Groups Artists & Musicians Classes & Lessons Events Friendship & Networking Lost & Found Rideshare Sports Teams Volunteers Travel & Travel Partners Skills & Language Swap Other

What is the difference between the 2.0 and 2.5 displacement of the Atenza?

1 Answers

IsabelaRose

07/30/25 6:13am

The differences between the 2.0 and 2.5 displacement of the Atenza: 1. The Atenza 2.0L is a naturally aspirated engine with a maximum of 158 horsepower. The Atenza 2.5L is also a naturally aspirated engine but with a maximum of 192 horsepower. 2. Both the 2.0 and 2.5 versions offer excellent handling, but the 2.5 provides stronger power when driving, and its transmission efficiency is several points higher than that of the 2.0. 3. Appearance differences: The entry-level version of the 2.5 Atenza comes equipped with 19-inch wheels. Larger wheels greatly enhance the car's appearance, as big wheels can cover many flaws. Moreover, the Atenza's design is already excellent, and the 19-inch wheels add the icing on the cake, making a significant visual difference. Therefore, choosing the 2.5 just for these larger wheels is worth it.

Was this review help?

16

4

Share

More Forum Discussions

How to Deal with Battery Overheating?

Battery overheating during charging may be caused by prolonged use leading to aging, increased internal resistance, dried-up electrolyte, or internal short circuits. As the battery undergoes repeated charge and discharge cycles, water molecules within gradually deplete, resulting in heat generation during electrochemical reactions. If the battery shows severe deformation, replacement is recommended. There are two types of battery overheating: discharge-induced and charge-induced. Check the battery's exterior. If deformation is minimal or absent, you can fully discharge the battery (single-cell voltage below 10.5V), pry open the cover, remove the valve caps, and use a clean syringe to inject approximately 10ml of distilled water into each cell. Reconnect the charger, monitoring the liquid level to ensure surface moisture. Once the charger indicator turns green, remove excess liquid, reinstall the valve caps and cover, and the battery is ready for use.

How Often Should Castrol Magnetec Engine Oil Be Replaced?

Castrol Magnetec is typically replaced every 6,000 kilometers or every six months. Below is a detailed introduction about Castrol Magnetec and other automotive engine oils: 1. Overview: Engine oil, also known as engine lubricant (English name: Engine-oil), has a density of approximately 0.91×10³ (kg/m³). It serves to lubricate and reduce friction in the engine, assist in cooling, seal against leaks, prevent rust and corrosion, and provide shock absorption. 2. Composition: Engine oil consists of two main components: base oil and additives. The base oil is the primary component of the lubricant, determining its fundamental properties, while additives compensate for and improve any deficiencies in the base oil's performance, imparting new characteristics. Additives are an essential part of the lubricant.

What is the position of the vehicle's center of gravity when overloaded?

When a motor vehicle is overloaded, the position of the vehicle's center of gravity shifts backward. To ensure directional stability during driving, vehicles are generally designed with the center of gravity positioned forward. However, when overloaded, the increased weight at the rear causes the center of gravity to shift backward. At certain speeds, even minor steering adjustments or disturbances can lead to severe yawing or spinning, resulting in skidding or rollover. Below is a detailed introduction about vehicle overloading: 1. Overview: Overloaded vehicles typically refer to those carrying loads exceeding the maximum capacity, commonly seen in trucks and buses. 2. Impact: When a vehicle is overloaded, its control capability is reduced, increasing the likelihood of traffic accidents.

What is the appropriate speed for third gear?

Corresponding speeds for gears one to five: First gear: This is the starting speed, typically between 0-5 km/h. Second gear: Corresponding speed is 5-20 km/h. Third gear: Corresponding speed is 20-40 km/h. Fourth gear: Corresponding speed is 40-60 km/h. Fifth gear: Corresponding speed is 60-100 km/h. Gear shifting techniques: Smoothness: When engaging a new gear, the clutch should be released appropriately, and the throttle should be promptly applied to ensure smoothness. Accuracy: Physical movements should be coordinated and precise; sloppiness can cause strong jerking sensations, reducing driving comfort. Speed: Gear shifting actions should be quick, which not only enhances the car's smoothness but also reduces kinetic energy loss and lowers fuel consumption. Timeliness: Perform correct gear shifts at the right moment, avoiding shifts that are too early or too late.

What is the top speed of the Zongshen RA2?

The top speed of the Zongshen RA2 is 115km/h. Here is some relevant information about motorcycles: Types of motorcycle licenses: Currently, there are three types of motorcycle licenses in China—F, E, and D. An F license only permits driving lightweight motorcycles with an engine displacement below 50CC, but this type of license is rarely pursued. An E license allows driving any two-wheeled motorcycle regardless of displacement, with no restrictions on engine size. A D license permits driving all two-wheeled and three-wheeled motorcycles. Therefore, as long as a driver holds an E license, they can operate all two-wheeled motorcycles, as there is no separate license for high-displacement motorcycles. Concept of a motorcycle: A motorcycle is a two or three-wheeled vehicle powered by a gasoline engine and steered by handlebars. It is lightweight, flexible, and fast, widely used for patrol, passenger and cargo transport, and also serves as sports equipment.

What causes an automatic transmission to be stuck in P gear and unable to shift?

An automatic transmission being stuck in P gear and unable to shift may be due to gear lock, or not fully braking when parking, directly shifting into P gear, causing gear braking instead of brake braking. Additionally, if the entire vehicle cannot be powered on, the automatic transmission's self-protection mechanism may also prevent shifting. Specific reasons are as follows: 1. Gear lock engaged; When driving, shifting from P gear to other gears, Japanese cars generally require pressing the shift lock switch, while German cars usually require stepping on the brake. The P gear also functions as a handbrake, preventing rollback on slopes below 15 degrees, but steeper slopes require using the handbrake. 2. Other reasons: P gear lock mechanism stuck and unable to reset; shift solenoid valve damaged, unable to complete shift commands; gear linkage damaged or broken; control computer malfunction.

Trending Ranking

What is the extent of a Level 3 water-damaged vehicle?

What does 20t mean in cars?

Where is the airbag connector located?

What is the fuel consumption per 100 kilometers for the Civic?

What causes severe power loss when the Cruze's air conditioning is turned on?

What is the actual measured ground clearance of the BMW X1?

What is the refund standard for a driver's license?

How to Check Fuel Consumption on the 2021 BMW 3 Series?

What does the Toyota logo look like?

Does the 2021 Avalon Still Have Engine Oil Emulsification?

More Forum Discussions

Who Yields When Three Lanes Merge into Two?

What is the tire specification of the hycan007?

What's the Difference Between High and Low Trim Levels of a Car?

What is the normal pressure of a truck turbocharger?

Help

Cookie

Cookie Settings

© 2025 Servanan International Pte. Ltd.