What is the difference between single-cylinder, twin-cylinder, and four-cylinder motorcycles?

What does oilchange mean when it appears on a car?

oil-change means oil change. The "oil-change" indicator usually appears on the car's dashboard. When the OIL-CHANGE light comes on, it means that the engine oil and lubricating oil should be replaced as soon as possible, which is a maintenance reminder for the vehicle. This indicator light is specifically used to record the mileage and time the car has traveled since the last maintenance. When the mileage and time reach the set value, this indicator light will turn on. The elimination method is as follows: When the power is off, that is, the screen is black and the car is completely powered off, press and hold the SEL button with your left index finger for 5 seconds without releasing it. Then, start the power with your right hand to light up the dashboard, and continue holding the SEL button with your left index finger for another 3 seconds. The OIL-CHANGE indicator light will then disappear. If the oil warning light comes on while driving, it indicates that the oil level is insufficient, and the car should not continue to be driven. Engine oil plays a significant role in lubricating the engine's operation. Insufficient oil will lead to inadequate engine lubrication, increasing engine wear. Additionally, the engine's cooling function may not work properly, causing the engine to overheat. Over time, the engine may even be damaged, which poses a significant danger to the occupants of the car. The viscosity of engine oil changes with temperature, so special attention should be paid to its performance under both low and high temperatures. For example, in 5W-30, the first number indicates low-temperature fluidity. 5W means it can withstand temperatures as low as -30°C. The smaller this number, the better the low-temperature fluidity, making cold starts smoother. The latter number represents the oil's kinematic viscosity at 100°C. A higher number means the oil can maintain its viscosity index better at high temperatures, which can also be understood as better lubrication performance under high-temperature conditions. When selecting engine oil, the following points should be noted: Choose engine oil based on the engine's requirements. It is unnecessary to use overly advanced oil in engines with lower requirements, nor should lower-grade oil be used in engines with higher requirements. Multi-grade oil should be preferred. Multi-grade oil is economical, long-lasting, and efficient, providing better protection for the engine. Due to the characteristics of multi-grade oil, it may appear darker prematurely and have lower oil pressure compared to regular oil, both of which are normal.

13

4

Share

What does it mean when the vehicle's eco light is green?

When the dashboard displays "eco," it indicates that the vehicle's economy mode is activated. Eco is an English abbreviation derived from Ecology (environmental protection), Conservation (energy saving), and Optimization (power). The Eco mode is further categorized into active eco driving mode and non-active eco driving mode. Eco mode is divided into active and non-active types. The difference lies in the fact that the active type has its own dedicated button, allowing the driver to choose whether to enable it. When the driver presses the eco mode switch, the dashboard indicator light immediately illuminates, and the vehicle automatically begins adjusting settings such as throttle opening, transmission shift logic, and air conditioning output power. Non-active eco mode does not have a dedicated button. When the dashboard eco indicator light turns on, it serves merely as a reminder function. The eco system automatically evaluates your driving behavior. If your current driving operation achieves the optimal fuel supply, the dashboard will simultaneously display the eco indicator light. Most vehicles employ the active eco driving mode, meaning they have a dedicated switch button. Therefore, eco mode can be enabled during daily driving. However, it is unnecessary to enable eco mode when driving at speeds exceeding 120 km/h, during idle parking, in N/P gear, or in manual mode—especially when climbing hills. Doing so would not only fail to demonstrate the fuel-saving characteristics of eco mode but also affect the vehicle's power. Additionally, eco mode typically becomes ineffective under the following circumstances: When the vehicle speed exceeds 120 km/h, the system prioritizes speed, causing the eco mode to automatically deactivate. During idle parking or when in N/P gear or manual mode, eco mode may also become ineffective. When high torque output is required, such as when climbing a hill, the engine control unit prioritizes ensuring sufficient power to drive the vehicle, and eco mode will not function in such scenarios.

20

0

Share

Where is the OBD interface of Foton View?

Foton View's OBD interface is located under the driver's seat. Open from behind the driver's seat to see the battery. The OBD connector is behind the battery and inside the battery box near the front of the vehicle. OBD stands for On-Board Diagnostics, which is a system that monitors the engine control system and other functional modules of the vehicle in real-time during operation.

11

5

Share

What are the causes of car water pump failure?

Car water pump failure causes: 1. Coolant leakage caused by aging water pump seals; 2. Over-tightened engine serpentine belt leading to premature wear; 3. Exceeding service life without replacement; 4. Bent pump shaft, worn shaft neck, or damaged threaded end; 5. Broken impeller blades or worn shaft bore; 6. Wear degree of water seals and bakelite washers; 7. Poor pump performance causing circulation issues that generate high temperatures, leading to leaks or broken blades; 8. Long-term antifreeze neglect causing internal corrosion that ultimately damages the pump.

19

4

Share

How to Clean an Oxygen Sensor?

Cleaning an oxygen sensor involves the following steps: 1. Remove the oxygen sensor from the vehicle; 2. Dissolve ferric chloride in water and mix it with hydrochloric acid; 3. Soak the oxygen sensor in the prepared solution for 10 to 15 minutes; 4. After soaking, wipe it clean with a clean cloth until the oxygen sensor turns white. The oxygen sensor is a critical feedback sensor in the electronic fuel injection engine control system, playing a key role in controlling vehicle exhaust emissions, reducing environmental pollution, and improving the fuel combustion quality of the car engine. Oxygen sensors are typically installed on the engine's exhaust pipe.

1

Share

What to Do When the Car Radar Doesn't Beep?

Solutions for when the car radar doesn't beep: First, check if the wiring connection at the bumper is intact; then check if the reverse lights turn on when shifting into reverse gear. If they don't, inspect whether the reverse light connection switch is faulty. Next, see if the computer displays any fault codes. If none of these issues are found, then check if the reverse radar itself is malfunctioning. Car radar is used for automobiles or other ground motor vehicles and includes various radars based on different technologies, each with different functions. Types of car radar: speed measurement radar, adaptive cruise control radar, collision avoidance radar, and other vehicle monitoring and control radars.

10

3

Share

What is the difference between single-cylinder, twin-cylinder, and four-cylinder motorcycles?

What does oilchange mean when it appears on a car?

What does it mean when the vehicle's eco light is green?

Where is the OBD interface of Foton View?

What are the causes of car water pump failure?

How to Clean an Oxygen Sensor?

What to Do When the Car Radar Doesn't Beep?

What is the reason for the starter noise when starting the car?

Where is the engine of the Trumpchi M8 produced?

What Lights Should Be Turned On When Temporarily Parking a Vehicle in the Rain?

What is the battery model for the Volkswagen Touareg remote key?