What is the difference between Mercedes with AMG and without?

What Causes the Reversing Radar to Stop Speaking?

Reversing radar stops speaking due to reasons such as the radar switch being turned off, wiring faults, or malfunctions in the radar itself. Radar Switch Turned Off: Most vehicles have a control switch for the reversing radar on the central control panel inside the car. If it is turned off, the reversing radar will not function. The solution is to turn on the reversing radar switch. Reversing Radar Wiring Fault: When the reversing radar wiring ages or breaks, the radar will fail to operate normally. Timely repair or replacement of the wiring harness is required. Radar Itself Malfunctioning: If the reversing radar is found not to beep, first check whether the power cable of the main unit is properly connected and if there is current. Then inspect whether the radar main unit wires have become loose. If both aspects are fine, the issue lies with the radar itself. The radar's buzzer may be damaged, in which case purchasing and installing a new buzzer will suffice. Alternatively, the reversing radar control unit itself may be damaged, leading to the entire reversing radar system malfunctioning. A power reset can be attempted first. If the issue persists after resetting, it is likely that the control unit itself is damaged, necessitating replacement or repair of the reversing control unit.

2

Share

What is the matching range between gears and vehicle speed?

1st gear is used for normal starting or climbing very steep slopes, with a speed generally around 10 km/h; 2nd gear is a transitional gear for acceleration after starting or for low-speed driving, with a speed generally around 20 km/h; 3rd gear is used at speeds between 20-40 km/h, commonly used for urban driving; 4th gear is used at speeds between 40-60 km/h; 5th gear can be used at speeds of 60 km/h or above. When driving a manual transmission, the gear shifting sequence must be from 1st to 2nd to 3rd to 4th to 5th gear, and skipping gears is not recommended. The downshifting sequence should be determined based on the condition of your vehicle, generally downshifting when the engine speed drops below around 1500 RPM. The larger the gear, the slower the rotation speed, corresponding to a lower gear and slower vehicle speed; the smaller the gear, the faster the rotation speed, corresponding to a higher gear and faster vehicle speed. If the gear does not match the engine speed, a mismatch between engine power and transmission gears will occur, leading to the phenomenon of the vehicle jerking forward and backward.

6

3

Share

How Many Years Does an Idle Speed Motor Last?

The lifespan of an idle speed motor is consistent with that of the car, meaning it lasts until the car is scrapped. Under normal circumstances, the idle speed motor does not need to be replaced. The idle speed motor is a component that controls the idle speed of a vehicle and is inherently not prone to failure. Therefore, there is no precise or uniform answer to the lifespan of an idle speed motor. If you need to clean the idle speed motor, it is essential to go to a professional auto repair shop or a 4S store and have it cleaned by professionals. Cleaning it yourself improperly can easily lead to issues. If the idle speed motor is damaged, it can cause intermittent idle stalling, where the engine sometimes stalls at idle but runs normally after restarting. This situation can have certain impacts on driving. For example, if stalling happens to occur during emergency braking, it can cause significant hazards. Once the engine stalls, the brake vacuum booster will not function, and the power steering system will fail. Combined with the driver's panic, this can easily lead to accidents.

6

5

Share

What Happens When the Idle Motor in a Car is Damaged?

Damage to the car's idle motor can result in the vehicle failing to start, the engine stalling automatically, and unstable idling, among other issues. The idle motor controls the idle air flow, making it prone to getting dirty. Excessive dust entering the idle motor can cause it to jam or become damaged. Vehicle Fails to Start: A damaged idle motor can prevent the vehicle from starting. The vehicle may require pressing the accelerator pedal to start, as the idle motor remains closed when damaged, blocking air from entering the intake manifold, thus preventing startup. Automatic Stalling: If the engine stalls automatically after starting, this is typically a fault caused by a damaged idle motor. Unstable Idling: After starting, the vehicle may experience idling vibrations or instability due to an unstable idle motor. This is usually caused by carbon buildup in the idle motor.

19

3

Share

How to Adjust Clutch Height?

Mechanical clutches primarily adjust their operation through the clutch cable, so simply adjusting the length of the clutch cable can modify the free travel and working travel of the clutch pedal. Hydraulic clutches cannot be adjusted; the only way to restore clutch height is by replacing the clutch friction disc. Reasons why the clutch becomes higher with use: Clutch disc wear: Manual transmissions use friction for power transmission, with the clutch disc serving as the friction medium. Over time, the clutch disc wears down and becomes thinner, leading to an increased working travel of the clutch and a higher engagement point. Excessive looseness in the clutch cable: For vehicles equipped with mechanical clutches, an overly long clutch cable results in excessive free travel and reduced working travel, causing the clutch engagement point to rise noticeably. Severe wear of the friction disc release fork: After the release fork wears out, the pedal will automatically rise a certain amount. However, the clutch disc still cannot fully engage with the friction disc, requiring the driver to lift the clutch higher for complete engagement.

14

0

Share

Where Can the Vehicle Accident Number Be Checked?

Vehicle accident numbers can be inquired about by consulting the insurance company. Generally, the driver needs to provide the time of the accident and relevant information to the insurance company, which will then retrieve the related records, as the insurance company keeps accident information highly confidential. The insurance company's records for car insurance claims are networked. The vehicle's traffic accident details can be checked through insurance claim records and vehicle insurance payment records, accessible via the insurance company's network. Additionally, such private information can only be queried by the driver with the vehicle's registration certificate. Typically, after a vehicle undergoes maintenance at a 4S shop, records are retained, and by inputting the vehicle's relevant information into the computer, all maintenance records can be retrieved. If the vehicle has been involved in a traffic accident, even the parts that were replaced can be found, allowing an assessment of the extent of the accident's damage. Similarly, one can check the demerit points online at the vehicle management office by selecting the personal driver's license information query, clicking to enter, inputting the driver's license number, name, and file number, and then clicking to query to display their driver's license information. To query the driver's license violation information, select the driver's license violation information query, again inputting the driver's license number, name, and file number for the query.

17

5

Share

What is the difference between Mercedes with AMG and without?

What Causes the Reversing Radar to Stop Speaking?

What is the matching range between gears and vehicle speed?

How Many Years Does an Idle Speed Motor Last?

What Happens When the Idle Motor in a Car is Damaged?

How to Adjust Clutch Height?

Where Can the Vehicle Accident Number Be Checked?

What are the precautions for reversing a car?

What Causes the Abnormal Noise When Turning the Steering Wheel While Reversing?

What Causes Sudden Abnormal Noises When Reversing?

Does Launch Control Damage the Car?