What is the difference between Mercedes-Benz with AMG and without AMG?

Under What Circumstances Should a Cylinder Head Be Replaced?

If the cylinder head develops cracks, it needs to be replaced, and if the cylinder head becomes deformed, it also requires replacement. The cylinder head is the engine's cylinder cover, and this component is part of the engine's combustion chamber, making it crucial for the engine. Below is an introduction to the relevant content: 1. From top to bottom, the engine consists of the valve cover, cylinder head, cylinder block, and oil pan. Inside the engine, there are components such as the crankshaft, piston, connecting rod, and within the cylinder head, there are intake valves, exhaust valves, and camshafts. Most car engines adopt a double overhead camshaft design, where the cylinder head houses two camshafts—one controlling the opening and closing of the intake valves and the other controlling the exhaust valves. 2. If the cylinder head experiences severe deformation, it must be replaced. A deformed cylinder head can compromise the engine's sealing, leading to issues like air and oil leaks. Similarly, if the cylinder head develops cracks, these can also cause air and oil leakage problems in the engine.

6

5

Share

What does fault code C0061 mean?

C0061 fault code indicates a malfunction in the lateral acceleration sensor. Here is an introduction to the lateral acceleration sensor: 1. In the Electronic Stability Program (ESP), the lateral acceleration sensor is used to measure the vehicle's lateral acceleration. Lateral acceleration refers to a key parameter related to the centrifugal force generated when the vehicle is turning. 2. Vehicle lateral acceleration refers to the acceleration perpendicular to the driving direction, which is caused by centrifugal force during turning maneuvers. Essentially, it represents the tendency of the car to be "thrown outward." The greater this acceleration, the more likely the vehicle is to deviate from its intended path. 3. The measurement principle of the lateral acceleration sensor is based on a deflection-extended mass system with capacitive detectors. Voltage is supplied by the ESP control unit. During turns, the generated lateral acceleration causes the mass element to overcome the force of the elastic rod, moving from its neutral position to a position corresponding to the lateral acceleration value. 4. Acceleration refers to the rate of change in velocity. Acceleration does not equate to speed. The function of this sensor is to measure acceleration, transmit the signal to the ECU for analysis, and then the ECU sends signals to relevant actuators to adjust the vehicle's driving state.

4

5

Share

How to Open the Hood of a BMW 3 Series GT?

Steps to open the hood of a BMW 3 Series GT: 1. First, park the car and turn off the engine. Enter the driver's compartment and locate the hood release handle on the left side near the driver's footwell. 2. The handle is marked with a front hood symbol and "x2," indicating it needs to be pulled twice. 3. Pull the handle twice to release the hood. 4. After opening, ensure both support rods are properly engaged. Here is an introduction to the BMW 3 Series GT: 1. Interior: The BMW 3 Series GT offers various interior colors, along with chrome trim and two premium wood trim options. 2. Features: Standard equipment includes electric speed-sensitive power steering, a sport steering wheel, an alarm system, a rearview camera, automatic trunk operation, a panoramic sunroof, electric front seat adjustment, driver seat memory, Bluetooth hands-free with USB port, headlight cleaning system, Dakota leather seats, and dual-zone air conditioning. 3. The 320i Design Line and above models also feature heated front seats, a navigation system, and ConnectedDrive. The top-tier 335i includes a head-up display, automatic parking assist, and a comfort access or start system. 4. Rear Design: The BMW 3 Series GT features clean lines without chrome accents. The trunk adopts a hatchback-style opening, offering 520L of cargo space, which is larger than the standard 3 Series (480L) and Touring models (495L).

18

4

Share

What Does Suspension Fault Mean?

Suspension fault means that there is a malfunction in the vehicle's suspension system. Common causes of faults are as follows: 1. Wear of ball joints or loosening of ball joint screws: Fault description: When the vehicle encounters bumps, a "clunking" sound is heard from the chassis. Fault inspection: Lift the vehicle and gently shake the tires to check the gap size, or use a pry bar to check the gap and looseness of each ball joint. Solution: Tighten the bolts and replace the new connecting rod, connecting ball joint, etc. 2. Aging or damage of the control arm rubber buffer: Fault description: When the vehicle encounters bumps, a "clunking" sound is heard from the chassis. Fault inspection: Use a pry bar to check each buffer rubber for cracks or aging. Solution: Replace the new swing arm buffer rubber or the new swing arm assembly. 3. Oil leakage or damage of the shock absorber: Fault description: A "clunking" or "squeaking" sound is heard when encountering bumps. Fault inspection: Check the shock absorber for signs of oil leakage, press the four corners of the car by hand to check the body's bounce and any abnormal sounds. Solution: Replace the new shock absorber. 4. Abnormal noise from the top rubber or plane bearing: Fault description: There is a "thumping" noise when passing over speed bumps, and a "squeaking" sound when turning the steering wheel in place. Fault inspection: Listen for sounds when turning the steering wheel in place or when lifting the car and turning the steering wheel. Solution: Replace the new top rubber or plane bearing, or add lubricant. Some sounds are caused by loose screws on the shock absorber. 5. Abnormal noise from the stabilizer bar bushing: Fault description: There is a "clunking" or "creaking" noise when driving and braking. Fault inspection: Check both sides of the bushing for clean, worn areas, and some are not easily detectable, usually eliminated by replacement. Solution: Replace the new stabilizer bar bushing. 6. Loosening of connecting and fastening parts: Fault description: A "clunking" noise occurs when encountering bumps. Fault inspection: Use a pry bar to check for looseness in each part. Solution: Tighten the loose screws.

4

3

Share

How to distinguish between the big V and small V of the Reiz?

You can distinguish them by the engine displacement of the car. The small V refers to the 3.0L displacement, while the big V refers to the 2.5L displacement. Here are the detailed explanations: 1. The big V and small V of the Reiz are mainly used to differentiate the engine displacement, with no significant differences in configuration. 2. The main differences in the Reiz model configurations are between the V and S versions. S is the standard version, while V is the luxury version. 3. However, the differences between the small V and S are minimal, and the small-wheel version of the Reiz can generally be referred to as either small V or S. 4. The big-wheel version is called the big V, which belongs to the mid-to-high configuration in terms of model specifications. 5. For example, the small V and S have basically the same configurations and both belong to the small-wheel version, but the small V includes additional features such as a sunroof, airbags, and heated seats compared to the S. 6. Compared to the big S, the big V adds features like a large roof lighting system, aluminum alloy accelerator pedals, 8-way electric adjustment for the front seats, and an automatic headlight cleaning device, elevating the interior configuration to a higher level.

15

5

Share

How to fold the mirrors on the Buick Excelle?

All models of the Buick Excelle support electric adjustment for the rearview mirrors, and the flagship version also comes with an electric folding function. The steps to adjust the Excelle's mirrors are as follows: 1. The mirror adjustment button is located on the left side of the driver's dashboard. 2. Turn the control knob to the left (L) or right (R) to select the corresponding side mirror. 3. Then push the control knob left, right, up, or down to adjust the mirror. 4. When in position O, no mirror is selected. 5. Before driving, adjust the seat position first, then adjust the rearview mirrors. Here are more details about the Buick Excelle: 1. The dimensions of the new Excelle are 4587mm in length, 1798mm in width, 1463mm in height, with a wheelbase of 2640mm. 2. The new Buick Excelle is equipped with two powertrain options: a 1.3T dual-injection turbocharged engine paired with a 6-speed DSS intelligent dual-clutch transmission, and a 1.0T dual-injection turbocharged engine paired with a 6-speed DCG intelligent dual-clutch transmission. The former delivers a maximum power of 120kW at 5500 RPM and a peak torque of 230N·m between 1800~4400 RPM, while the latter offers a maximum power of 92kW at 5600 RPM and a peak torque of 170N·m between 1700-4400 RPM.

18

5

Share

What is the difference between Mercedes-Benz with AMG and without AMG?

Under What Circumstances Should a Cylinder Head Be Replaced?

What does fault code C0061 mean?

How to Open the Hood of a BMW 3 Series GT?

What Does Suspension Fault Mean?

How to distinguish between the big V and small V of the Reiz?

How to fold the mirrors on the Buick Excelle?

Where is the license plate with 'Wan W' from?

How often should the brake fluid be changed for a Corolla Hybrid?

How to Adjust the Rearview Mirror of Volkswagen Magotan?

Where is the cabin air filter located in a Ford Mondeo?