What is the difference between front and rear brake pads?

1 Answers
DeSkylar
07/29/25 3:43pm
The biggest difference between front and rear brake discs is that the front brake discs are larger. This is because when a car brakes, whether it's front-wheel drive or rear-wheel drive, the center of gravity shifts significantly forward, causing the front wheels to bear more pressure. This is precisely why front brake discs are larger than rear ones. Below are some brake maintenance tips: 1. Protection: Use high-temperature protection to prevent corrosion in the brake system, avoid brake pads seizing due to high temperatures, and eliminate brake squealing. 2. Cleaning: Clean oil stains, dirt, and friction dust from brake discs, brake drums, and any other components to ensure good heat dissipation of the brake discs.
Was this review help?
14
0
Share
More Forum Discussions

Can Airbags Be Installed by Oneself?

Do not install airbags on your own for vehicles without them. Here is relevant information: 1. The airbags in vehicles are controlled by an airbag controller and are connected to it via wiring harnesses. Self-installation means not only adding airbags but also modifying the airbag controller. These controllers are typically produced by joint-venture manufacturers, with very few from domestic manufacturers, making modifications difficult. 2. Issues arising from unauthorized modifications will not be the responsibility of 4S shops or vehicle manufacturers. During the vehicle design process, if space is reserved for airbag installation, it can be installed; otherwise, it should not be attempted. Additionally, it is best not to install airbags on your own. Airbag deployment has high requirements, such as deployment timing, deceleration, angle, etc., all of which require real-vehicle testing. Approximately fourteen crash tests are needed to set the relevant parameters.
15
3
Share

Can You Continue Driving with a Noisy Front Wheel Bearing?

You should not continue driving with a noisy front wheel bearing and need to visit a repair shop for inspection and maintenance as soon as possible. Below are the precautions for using car bearings: 1. Check the bearings: Whether it's a new or old car, promptly inspect the car bearings to prevent issues. During inspection, pay attention to whether the bearings show signs of wear, if there is friction noise when rotating, or if the suspension combination wheel slows down abnormally when turning. 2. Replace in pairs: If the front wheel bearings are found to be damaged, they need to be replaced in pairs to ensure driving safety and prevent abnormal conditions. 3. Precautions for disassembly: Professional tools are required when disassembling tire bearings. Unauthorized disassembly can easily affect the bearing's sealing and also have a certain impact on its service life.
14
4
Share

What does vsv mean?

The vsv light on a car is a fault indicator for side slip control. The SVS on the dashboard is the key chip anti-theft indicator light. If this light does not flash when the power is turned on, it means the engine has read the key chip password. Conversely, if this light flashes rapidly. Reasons for the vsv light to illuminate: Problems with the car's braking system: There are many reasons for problems with the car's braking system, including excessive wear of brake pads, lack of brake fluid, brake pump leakage, etc. Generally speaking, the brake pads of a car need to be replaced after driving about 40,000 kilometers. During car maintenance, the braking system must also be strictly inspected to avoid potential safety hazards. Problems with the engine power system: When the car engine has severe carbon deposits, engine misfire, spark plug failure, low fuel quality, or excessively high engine temperature, it may cause problems with the engine power system. In such cases, it is necessary to go to a repair shop or 4S store to have professionals inspect and repair it to avoid potential safety hazards.
2
5
Share

What does vw50800 mean?

vw50800 is a newly developed long-life, low-energy-consumption gasoline engine oil under the VW standard, specifically designed for viscosity grade 0W-20. Below is an introduction to engine-related content: Energy Conversion: An engine is a machine capable of converting other forms of energy into mechanical energy, including internal combustion engines (reciprocating piston engines), external combustion engines (Stirling engines, steam engines, etc.), jet engines, electric motors, etc. For example, internal combustion engines typically convert chemical energy into mechanical energy. Device: The term engine can refer to both the power generation unit and the entire machine including the power unit (e.g., gasoline engines, aircraft engines). The engine was first developed in the UK, so the concept of the engine originates from English, with its original meaning referring to "a mechanical device that generates power."
12
4
Share

What is the difference between standard wheelbase and long wheelbase?

The main difference between long wheelbase and standard wheelbase lies in the increased wheelbase, longer body, larger interior space for more comfortable seating, and better driving stability. The BMW 3 Series long wheelbase is domestically produced in China, with an extended wheelbase tailored for the Chinese market, while the standard wheelbase is imported, offering smaller space but no significant technical differences. Below are the relevant details: 1. In terms of appearance, the new car's design remains unchanged, but the overseas new 4 Series' 18-inch 848M wheels will be equipped on the 325i M Sport model, while other M Night Shadow models offer them as optional. The vehicle interior also comes standard with Volcano Red Sensatec leather upholstery across the entire lineup. 2. Regarding configurations, the new car comes standard with cruise control and a rearview camera with parking assist function. Models other than the 320i/Li will feature standard keyless entry.
13
3
Share

What brand of motorcycle is TONTSE?

"TONTSE" engines are used in Dongyi motorcycles produced by Guangzhou Dongyi Motorcycle Co., Ltd. Dongyi Motorcycle Co., Ltd. is a wholly Taiwanese-owned professional manufacturer of motorcycles and engines. In 2005, it passed the motorcycle entry review by the National Development and Reform Commission. Its predecessor was Taiwan Dongze Industrial Co., Ltd., which began the research, development, and production of Dongze (TONTSE) engines in mainland China in 1992, with an annual production capacity of 600,000 units. Below are some motorcycle maintenance tips: Cleaning: Wash the motorcycle when it gets dirty or after being exposed to rain, as rain is acidic and highly corrosive to metal and plastic. After washing, apply a layer of wax to help resist damage from acid rain and sunlight. Engine maintenance: At 6,000 kilometers on the odometer, which is during the normal driving phase when changing to the second bottle of semi-synthetic oil, add an anti-wear agent to ensure the engine's lifespan is extended and the motorcycle's performance is improved.
4
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.