What is the difference between a parking area and a service area on the highway?

Can a Truck Run Without Urea?

Trucks (i.e., freight vehicles) can continue to operate without urea, but it is necessary to replenish it as soon as possible. Operating a truck without urea will have the following effects: 1. The urea pump is prone to crystallization and clogging: If a truck runs without urea for an extended period, the circulating urea pump nozzle, pipelines, and urea pump are prone to crystallization, clogging, or high-temperature damage. 2. Torque limitation: The truck's emission warning light will illuminate, torque will be limited, resulting in insufficient power, making it feel sluggish to drive. 3. Failure to pass annual inspection: Trucks without urea will fail the annual inspection and may face penalties. The role of urea for heavy-duty vehicles: 1. Catalytic function: Urea is primarily added to vehicles with diesel engines because diesel engines emit harmful nitrogen oxide (NOx) gases, causing environmental pollution. Long-term inhalation of these exhaust gases poses significant harm to human health. To mitigate this hazard, vehicles with diesel engines use urea, which has a catalytic function. When encountering nitrogen oxides, it triggers a chemical reaction, converting them into nitrogen and water before being expelled. 2. Reduction of nitrogen oxide emissions: Qualified urea solutions consist of 32.5% ultra-pure urea and pure water. The urea solution reacts with NOx through selective catalytic reduction (SCR), converting it into nitrogen, oxygen, and water, thereby reducing nitrogen oxide emissions. 3. Urea plays a crucial role in vehicle power and fuel consumption: If diesel exhaust fluid (DEF) is not used, or if substandard or low-purity urea solutions are employed, the vehicle's engine will automatically decelerate. Additionally, inferior-quality DEF can contaminate the SCR catalytic converter's catalyst, causing damage to the after-treatment system components.

1

5

Share

Where is the MG car engine from?

MG car engines are jointly developed by SAIC Motor and General Motors and are produced in SAIC's engine factories. Most MG cars use the "Blue Core" SGE20T engine. For example, the MG MG6 is equipped with a 1.5-liter turbocharged engine, delivering a maximum power of 124 kW, a maximum torque of 250 Nm, a maximum power speed of 5500 rpm, and a maximum torque speed of 170 Nm. For the daily maintenance of MG car engines, the following methods can be applied: Use lubricating oil of the appropriate quality grade. For gasoline engines, select SD-SF grade gasoline engine oil based on the additional equipment in the intake and exhaust systems and usage conditions. For diesel engines, choose CB-CD grade diesel engine oil according to mechanical load, with the selection standard not lower than the manufacturer's requirements. Regularly change the engine oil and filter. The quality of any grade of lubricating oil will degrade over time. After a certain mileage, its performance deteriorates, leading to various engine issues. To prevent malfunctions, change the oil regularly based on usage conditions and maintain an appropriate oil level. When oil passes through the fine pores of the filter, solid particles and viscous substances accumulate in the filter. If the filter becomes clogged and oil cannot pass through, it may rupture the filter or open the safety valve, allowing oil to bypass the filter and carry contaminants back to the lubrication areas, accelerating engine wear and increasing internal contamination. Regularly clean the crankcase. During engine operation, high-pressure unburned gases, acids, moisture, sulfur, and nitrogen oxides from the combustion chamber enter the crankcase through the gap between the piston rings and cylinder walls. These mix with metal particles from component wear to form sludge. Small amounts remain suspended in the oil, while larger amounts precipitate, clogging filters and oil passages, making lubrication difficult and causing wear. Periodically use a radiator cleaner to flush the radiator. Removing rust and scale not only ensures the engine operates smoothly but also extends the overall lifespan of the radiator and engine.

17

2

Share

What does the yellow ABS light mean?

When the ABS light is displayed on a car, it indicates a malfunction in the vehicle's Anti-lock Braking System. During emergency braking, if the wheels lock up, the vehicle may lose control and skid, preventing the driver from slowing down or adjusting the vehicle's trajectory, which poses significant safety risks. There are various states in which the ABS light may illuminate, with different causes and solutions for each state. The details are as follows: State 1: ABS warning light stays on (most common). Cause 1: The ABS wheel speed sensor's sensing area is covered by dirt, mud, or other contaminants, affecting the sensor's ability to detect the corresponding speed signal. This prevents the ABS computer from determining the vehicle speed and the wheel's slip rate, thus failing to issue appropriate commands to regulate braking. Solution: Clean the dirt from the wheel speed sensor and adjust the gap between the sensor and the signal ring to restore normal function. Cause 2: Loose connections in the system wiring or poor contact in the ABS relay can lead to signal issues and system failure. Solution: Check the wiring connections and reconnect any loose parts. State 2: ABS warning light intermittently illuminates but turns off when accelerating. Cause: When multiple vehicle electrical devices are in use, the battery voltage may drop below 10.5V. As the engine speed increases and the voltage rises, the ABS light turns off. This can also occur if the ABS system's power supply voltage is too low due to poor contact or grounding issues. Solution: Check the battery's specific gravity; inspect the charging system; examine the power supply (e.g., voltage relay or poor power contact). State 3: ABS warning light stays on after engine start and only turns off when the engine is turned off (IGFF). Cause: Poor grounding contact in the ABS hydraulic valve body; loose wiring connections in the ABS hydraulic valve body; ABS computer malfunction. Solution: Loosen and then retighten the grounding screws on the hydraulic valve body, cleaning the contact surfaces if necessary; check for enlarged gaps in the connectors; replace the ABS or ABS/ASR computer. State 4: ABS warning light illuminates during high-speed driving. Cause: During high-speed driving, the ABS computer detects a significant discrepancy between the rear and front wheel speed signals; incorrect tire or wheel rim specifications. Solution: Refer to the vehicle's tire and wheel rim specifications, as indicated on the label near the fuel tank cap. State 5: ABS warning light intermittently illuminates. Cause: Improper adjustment of the brake light switch; poor internal contact in the brake light. Solution: With the engine running, press the brake pedal and use a finger to push the brake switch linkage all the way down, then release the brake pedal to complete the self-setting position; replace the brake light switch if necessary.

14

4

Share

What is the fuel consumption of the Geely Vision X1?

Geely Vision X1 has a total of 4 models. Among them, the 2017 1.0L manual Youth Edition model equipped with a 68 horsepower engine has an NEDC fuel consumption of 5.1L per 100 kilometers. The other three models, including the 2017 1.3L manual Fun Edition, are equipped with an 88 horsepower engine and have an NEDC fuel consumption of 5.3L per 100 kilometers. The fuel tank capacity of different Geely Vision X1 models varies, and the distance that can be covered on a full tank of fuel is as follows: Models equipped with a 68 horsepower engine have a fuel tank capacity of 35L, and the distance that can be covered on a full tank is 35/5.1*100=686KM. Models equipped with an 88 horsepower engine have a fuel tank capacity of 35L, and the distance that can be covered on a full tank is 35/5.3*100=660KM. The fuel consumption of a car is directly related to five major factors: driving habits, the car itself, road conditions, natural wind, and environmental temperature. Specific factors that can increase fuel consumption are as follows: Driving habits: Aggressive driving, such as sudden acceleration, frequent overtaking, and not easing off the throttle before a red light, can increase fuel consumption. The car itself: Cars with larger engine displacements generally consume more fuel than those with smaller displacements because larger displacements usually mean higher power, requiring more gasoline to burn and perform work. Heavier cars also consume more fuel because greater weight requires more driving torque. Road conditions: Driving on dirt roads, muddy roads, soft surfaces, or mountainous roads increases resistance and fuel consumption. Natural wind: Driving against the wind or on windy days increases the car's resistance and fuel consumption. Low environmental temperatures: When the engine block temperature is low, the gasoline injected during a cold start does not atomize easily, requiring more gasoline to be injected for combustion, which increases fuel consumption. Additionally, at low temperatures, the engine's computer will control the engine to run at higher RPMs to warm up, which also increases fuel consumption.

16

1

Share

What Brand is Karlmann?

Karlmann is a brand under IAT, an independent Chinese automotive brand. Here are some key details about Karlmann: 1. Positioning: Karlmann is a high-end customized vehicle, with only ten units produced globally. It was designed in Europe and manufactured in Germany, classified as a super SUV model. 2. Powertrain: The vehicle is equipped with a 6.8-liter V10 engine, which is fitting for such a massive vehicle. 3. Exterior: The overall design of the vehicle incorporates sharp, angular lines, ensuring it stands out and turns heads when driven in urban settings.

2

5

Share

Can partial polishing be done?

Minor scratches can be treated with partial polishing, but this is only a temporary solution. Because polishing will inevitably damage the paint surface, after two times the paint will become very thin. After polishing, regular waxing is necessary, otherwise the paint surface will quickly develop cracks, become matte, or fade due to aging. Benefits of polishing: For vehicle paint surfaces that are oxidized, dull, or have scratches, polishing can remove oxides and contaminants, restoring the cleanliness of the paint surface. Drawbacks of polishing: Polishing will thin the car paint, and if not done carefully, it may even polish through to the primer.

2

0

Share

What is the difference between a parking area and a service area on the highway?

Can a Truck Run Without Urea?

Where is the MG car engine from?

What does the yellow ABS light mean?

What is the fuel consumption of the Geely Vision X1?

What Brand is Karlmann?

Can partial polishing be done?

What is the tire size for Audi A4?

Where is the rearview mirror heating switch for the Honda Civic?

BYD Tang DM Highway Fuel Consumption?

Does the Buick GL8 have a hybrid version?