What is the Damei X5?

Can Subject 1 and Subject 2 be taken at the same time?

Subject 1 and Subject 2 cannot be taken simultaneously. According to the "Regulations on the Application and Use of Motor Vehicle Driver's Licenses," the waiting period between Subject 1 and Subject 2 varies depending on the type of license. For a C-class license, the waiting period is 10 days after passing Subject 1, while for A and B-class licenses, it is 20 days before Subject 2 can be scheduled. This provides ample time to prepare for Subject 2. Each Subject 2 exam appointment includes two attempts. If the first attempt is unsuccessful, a free retake is allowed. If the retake is not attended or is still unsuccessful, the exam session ends. Within the validity period of the driver's license learning phase, the number of Subject 2 exam appointments must not exceed five. If the fifth attempt is still unsuccessful, the results of other previously passed subjects will be invalidated. To continue learning for the driver's license, one must restart from Subject 1. For example, the C1 license's Subject 2 exam includes: driving a motor vehicle to complete test items within a designated area, demonstrating mastery of driving skills, and assessing the ability to judge the vehicle's spatial position. Subject 2, also known as the "small road test," consists of five mandatory items: reverse parking, parallel parking, hill start, right-angle turn, and curve driving. Some regions include a sixth item: highway toll card collection. Subject 2 exam tips: After getting into the car, adjust the seat and mirrors to a suitable position and state, and always fasten the seatbelt. For parallel parking, find the correct angle quickly, turn the steering wheel swiftly, and react promptly to match the car's speed. For hill starts, remember to engage the handbrake, turn on the left turn signal when starting, release the handbrake, and maintain clutch control while gently pressing the accelerator to avoid stalling or rolling back. For right-angle turns, identify the turning point quickly and react in sync with the car's speed to prevent deviation. For curve driving (S-turn), slow down and proceed carefully. Those with good driving sense may pass smoothly in one go. For reverse parking, control the speed, identify reference points accurately, and make slight adjustments if deviations are observed in the mirrors. The driver's license test consists of three subjects: Subject 1, Subject 2, and Subject 3. Subject 1 covers traffic safety laws, regulations, and related knowledge. Subject 2 is the field driving skills test. Subject 3 is divided into two parts: road driving skills and safe driving knowledge. The safe driving knowledge test is conducted after Subject 3, often referred to as Subject 4, though this term is not officially recognized in regulations (e.g., the Ministry of Public Security's Order No. 123).

8

2

Share

What are the differences between the E260 and E300?

The differences between the Mercedes-Benz E260 and E300: 1. Different prices: The base model of the Mercedes-Benz E300 (Fashion trim) is more expensive than the base model of the Mercedes-Benz E260 (Sport trim). There is also a significant price gap between the top configuration of the E200 4MATIC Sport and the E300 Fashion trim. 2. Different powertrains: The Mercedes-Benz E260 is equipped with a 2.0T low-power engine with a maximum power of 135KW and a maximum torque of 280N·m, supplemented by a 48V mild hybrid system. In contrast, the Mercedes-Benz E300 features a 2.0T high-power engine with a maximum power of 190KW and a maximum torque of 370N·m. 3. Configuration differences: As the entry-level model in the E-Class lineup, some features of the Mercedes-Benz E200 require optional upgrades, unlike the E300, which includes them as standard. Examples include keyless entry for all doors, a 360-degree panoramic camera, and a steering wheel memory function.

6

2

Share

Which point on the wiper should be used to judge the 30 cm distance in Subject 2?

To judge the 30 cm distance, observe the position between the root of the right wiper and the right washer nozzle. Key points to note for Subject 2: 1. Reversing into the garage: Main deduction points: Pressing the line while reversing, the car not entering the garage, exceeding the time limit, not following the designated route. After the new regulations, a time limit of 210 seconds was added for reversing into the garage. During the test, reverse into the right garage first, then the left garage. Not following this order will result in disqualification. Once the car is in the garage, steer towards the side where there is more space between the car body and the line. It's better to steer early rather than late. While adjusting the car body, be careful not to miss the stopping point. 2. Parallel parking: Main deduction points involve the turn signal, 30 cm margin, and pressing the line. When entering the test area, steer right in advance and observe the highest point of the wiper aligning with the roadside line to adjust the 30 cm margin. While reversing, remember the first right full lock, straighten, then left full lock, park in the garage, turn on the left turn signal, and observe the rearview mirror when exiting to prevent the wheels from pressing the line on either side. 3. Right-angle turn: Main deduction points involve the turn signal and pressing the line. After entering the test area, turn on the turn signal, and turn it off after the voice prompt. Incorrect turn signal operation deducts 10 points. After entering the right-angle turn, adjust the car body to maintain a 30 cm margin from the line. The observation point is the same as in parallel parking. When fully locking the steering, slightly release the clutch to prevent stopping or stalling midway. Straighten the car body after the rear wheels exit to prevent the wheels from pressing the line. 4. Curve driving: Main deduction point is the wheels pressing the line. During the test, pay attention to the first part (right turn), sit upright, align the left window corner with the inner side of the left yellow line, and continuously adjust the direction; the latter part (left turn), extend your head out of the window, align the left window corner with the inner edge of the left yellow line, and continuously adjust the direction. Finally, straighten the car body to the left (no stopping allowed throughout). 5. Hill start and stop: Main deduction points involve the 30 cm margin between the car body and the line, the 50 cm stopping point, stalling during start, rolling back during start, and forgetting to release the handbrake during start.

1

3

Share

What are the steps for vehicle glaze sealing?

Here is the process for car glaze sealing: 1. After washing the car, use a decontamination material to remove rust, overspray, dust particles, and resin impurities from the car paint surface; 2. Polish to remove attached debris and oxidized layers from the car paint surface; 3. Eliminate swirl marks; 4. Treat the car paint with glaze sealing material; 5. Gently polish the paint surface with a dust-free cloth and wave cotton. Precautions after car glaze sealing are: 1. Do not wash the car with water within 8 hours; 2. Try to avoid washing the car after the glaze sealing is done. Additional information: Car glaze sealing refers to the formation of a protective film on the car paint surface after multiple processes, which has the functions of blocking ultraviolet rays, preventing oxidation, and resisting high temperatures and acid rain.

11

4

Share

How to Remove the Wiper Plug?

Here are the steps to remove the wiper plug: 1. Lift the wiper and press the square button on the wiper to detach it from the metal swing arm. 2. It's best to cover or wrap the wiper swing arm with a soft cloth to avoid damaging the glass surface, then gently return it to the windshield. 3. Thoroughly clean the wiper once, wipe it dry, and set it aside. 4. Take the new wiper rubber strip out of its packaging and soak it in soapy water to lubricate it, making installation easier. 5. Hold the original wiper and use your fingers to pull the rubber strip back and forth on one side. You'll notice that one side can be pulled while the other side remains fixed. 6. Locate the fixed side, use a thin flat-head screwdriver to pry open the plastic plug on this side of the wiper, and then you can remove it.

13

1

Share

How to replace the cabin air filter of Peugeot 408?

Peugeot 408's cabin air filter is located inside the trim panel near the front passenger's left leg. To replace the cabin air filter of Peugeot 408, you first need to remove a trim panel. There is a handle on the cover behind the trim panel. Open the cover to replace the cabin air filter. Here is some information about car cabin air filters: A car cabin air filter is a specialized filter designed for air purification inside the vehicle cabin. It uses highly efficient adsorption material - activated carbon composite filter cloth combined with long-fiber non-woven fabric. The compact structure can effectively filter smoke odor, pollen, dust, harmful gases, and various odors, achieving excellent filtration and adsorption of particulate impurities.

3

4

Share

What is the Damei X5?

Can Subject 1 and Subject 2 be taken at the same time?

What are the differences between the E260 and E300?

Which point on the wiper should be used to judge the 30 cm distance in Subject 2?

What are the steps for vehicle glaze sealing?

How to Remove the Wiper Plug?

How to replace the cabin air filter of Peugeot 408?

What Preparations Are Needed for a Vehicle Inspection Within Six Years?

What issues should be noted when using a car battery?

When are highways free of charge?

Where to Find the Vehicle Identification Number?