What is the correct way to warm up a Roewe RX5?

2 Answers
McRobert
07/25/25 5:21pm
The correct way to warm up a Roewe RX5 is: First, start the vehicle and let it idle for about a minute, then begin driving slowly. Once the water temperature reaches the normal level, you can drive according to your usual habits. Below is some related information about warming up the car: 1. The main reason for warming up the car is that after prolonged parking, the engine oil flows back into the oil pan at the bottom of the engine. Therefore, when starting, the upper part of the engine is in a state without oil and lacks lubrication. It takes about 30 seconds after starting for the oil pump to circulate the oil to the parts that need lubrication the most, such as the pistons, connecting rods, and crankshaft. 2. Both summer and winter require warming up the car, with winter requiring a longer warm-up time than summer. After a night of inactivity, the lubricating oil on the friction surfaces of the engine has mostly dissipated, losing its protective oil film. Low temperatures increase the viscosity of the lubricating oil, reducing its adhesion and fluidity, which increases the resistance during engine startup. Driving under these conditions will increase the engine's load and cause unnecessary wear. 3. Research from authoritative institutions shows that the wear during cold starts accounts for about half of the total wear. Proper idling to warm up the car can reduce this wear, thereby extending the engine's lifespan. At low temperatures, metals exhibit reduced elasticity and wear resistance. Only at normal operating temperatures can the engine achieve the proper clearance and maintain optimal performance.
Was this review help?
8
2
Share
PenelopeMarie
08/11/25 10:09pm
I've been driving the Roewe RX5 for a while now, and warming up the engine is something that requires attention. The correct method is not to rush into driving fast after starting the car; instead, let the engine idle for about 30 seconds to a minute, possibly a bit longer in cold weather. Why do this? During a cold start, the oil hasn't circulated properly, and stepping hard on the accelerator can easily wear out components. The Roewe RX5 is an SUV with a larger engine, so driving becomes smoother after warming up. It's best to drive at low speed for a few minutes, keeping the speed under 40 km/h, to let the water temperature rise naturally. I picked up this habit from experienced drivers—it can extend the engine's lifespan and reduce maintenance hassles. When encountering bumps or going uphill on the road, a properly warmed-up car responds more swiftly, making it much safer. Just don't let it idle for too long, as it wastes fuel and affects emissions. Remember these simple steps: start the engine, wait a bit, and then drive gently.
Was this review help?
18
1
Share
Expand All
More Forum Discussions

Where is the hazard warning light switch for automatic transmission?

Commonly, the hazard warning light switch is located on the center console to the right of the steering wheel. However, in some models, the switch may be positioned below the center console. Introduction to hazard warning lights: Also known as 'emergency flashers' or commonly referred to as 'hazard lights,' the hazard warning light switch is an independent feature, typically marked by a red triangle. Pressing it once activates the hazard lights. These lights serve as a signal on vehicles, primarily to alert other drivers and pedestrians that the vehicle is experiencing a special situation, prompting them to yield or avoid promptly. Usage scenarios for hazard warning lights: If other vehicles need to slow down or even stop to yield, it is generally necessary to turn on the hazard warning lights.
14
4
Share

How to Report Illegal Use of Emergency Lanes on Highways?

To report illegal use of emergency lanes on highways, you can submit the report through the WeChat account opened by the local traffic police headquarters' highway division. The reporting requirements are: You should take more than 3 images; the pictures should clearly reflect the surrounding environment, such as road signs, service area markers, obvious landmarks, etc. When submitting the report, you should also inform the traffic police department of the direction of travel; the shooting time should be determined. If you encounter an unsolvable problem such as a vehicle breakdown, you should park the car in the emergency stopping zone, turn on the hazard warning lights, place a warning sign 150 meters behind the vehicle, and during nighttime, rain, fog, or other adverse weather conditions, you should also turn on the side marker lights, tail lights, and rear fog lights. All occupants must move to a safe area, and if necessary, call the highway emergency number for assistance. Conditions for using the emergency lane: Sudden illness of a passenger in the vehicle; when the vehicle has a sudden breakdown and cannot be driven normally; emergency official vehicles.
7
2
Share

What is the initialization method for Wuyang-Honda's i-FI electronic fuel injection system?

The method is: the engine kill switch must be in the ON position; turn the ignition key to ON and immediately turn it off, then wait for 20 seconds; turn the key on and off 5 times at a rate of one cycle per second; wait another 20 seconds, then turn the ignition key to ON. If the yellow malfunction indicator light on the dashboard does not illuminate and the fuel pump operates normally, the reset is successful. Left turn signal operation method: Push the light control lever downward to activate the left turn signal. Turn signal operation method: Simply lift the control lever upward to activate. High beam operation method: After switching the lights to low beam, push the lever forward to activate high beam. The high beam and high beam flash functions are controlled by moving the lever to corresponding positions.
3
3
Share

How to Use the Car Push-On-Off Pedal?

Car push-on-off pedal is the foot brake. Convenient for parking: This is the foot brake, serving the same function as the handbrake, mostly found in automatic transmission vehicles, making it easier for women with less strength to complete parking effortlessly. Preventing vehicle skidding: It serves the same purpose as the conventional handbrake in cars, mainly used to prevent the vehicle from sliding when parked. Never press it while driving, as it won't spring back automatically; you need to press it again to release. Pressing it while driving can easily engage the foot brake. Replacing the handbrake: The parking brake, commonly known as the foot brake, is now used in many car models to replace the handbrake.
1
2
Share

How to Remove Residual Adhesive from Car Film?

Methods to remove residual adhesive from car film: 1. Wipe it off with a wet cloth; 2. Spray professional adhesive remover and then wipe it off; 3. Use foam cleaner to remove. The functions of car film are: 1. It can prevent glass from accidental breakage or scratches. When the glass with film is accidentally impacted and broken, the tightly bonded film will slow down the impact speed of glass fragments, playing an anti-explosion role; 2. It can avoid direct sunlight exposure to the interior decorations and items. High-quality car film can effectively absorb more than 90% of ultraviolet rays; 3. It can filter glare and enhance driving safety.
5
2
Share

Should You Turn Off the Engine Before Shifting to P Gear or Shift to P Gear Before Turning Off the Engine?

It is best to turn off the engine before shifting to P gear. Engine shutdown method: Normally, when parking the car, first bring the car to a complete stop, then shift the gear to N gear, engage the handbrake, turn off the engine, and then shift to P gear. This is the correct way to turn off the engine. The correct steps for starting an automatic transmission car are: Press the brake, engage the handbrake, start the engine (do not directly shift to D gear; shift to N gear first and then start the engine, then shift from N gear to D gear), release the handbrake, release the foot brake, and release the handbrake (for electronic handbrakes, simply press the button briefly). You can choose to warm up the car in place, and the time can be determined based on the environment. Press the accelerator and start moving. Depending on the road conditions, press the accelerator smoothly to accelerate and drive safely.
13
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.