What is the correct way to steer the wheel?

What Causes a Motorcycle to Have No High Voltage Spark When Starting?

When a motorcycle has no high voltage spark during starting, it indicates an issue with the ignition system components or their wiring connections. Below are the specific reasons: Potential wiring issues in the following parts: Faults in the spark plug, ignition coil, ignition module, magneto coil, ignition switch, kill switch, and side stand kill switch (if equipped), as well as open or short circuits in their wiring connections. For fuel-injected motorcycles, also check for issues with sensors related to ignition and the ECU. Corresponding solutions: Conduct a step-by-step inspection: check the spark plug, high-tension wire, ignition coil, and trigger coil. The engine cover on the left side usually doesn't have issues—problems are mostly in the electrical circuit. Sometimes, a faulty ignition switch circuit can shut down the entire electrical system. First, remove the spark plug cap, insert a screwdriver into the cap's electrode, and ground it to the frame. Then, kick-start the engine to test for spark. If there's spark, the issue is with the spark plug. If not, the problem lies elsewhere—start by checking if the spark plug is faulty.

17

5

Share

Does Transmission Removal Affect the Car?

After removing the transmission, if the screws are properly tightened and installed with the correct torque, there will be no impact on the engine. The general disassembly sequence is: transmission cover, first shaft, second shaft, intermediate shaft, and reverse gear shaft. Installation Inspection: Before installing the transmission cover, check the work area for any missing parts, ensure there is no axial movement in the shafts and fixed gears, verify the integrity of all gaskets, and confirm that all meshing gears engage fully across the entire tooth width. Manually slide the gears to check if they can move axially to full tooth width engagement. Rotate the first shaft by hand and test each gear to ensure smooth and flexible rotation without any sticking. Disassembly Inspection: All disassembled parts should be thoroughly cleaned and inspected. Replace any parts that cannot be reused. Generally, oil seals and gaskets that have been removed should not be reused and should be replaced.

14

1

Share

Can I Turn on Cool Air Without AC?

Turning on cool air without AC is not possible. Below are explanations regarding why AC must be turned on for cool air and precautions for using cool air in cars: Reasons why AC must be turned on: Cool air requires AC to be turned on. AC activates the air conditioning compressor, which starts working only when the AC button is pressed. The car air conditioning cooling system consists of a compressor, condenser, receiver-drier, expansion valve, evaporator, and blower. Precautions for using cool air in cars: When the air conditioning is on, try to avoid smoking. If you must smoke, adjust the ventilation control to the external circulation position. Never rest or sleep for extended periods in a car with the air conditioning running. In summer, parked cars can become extremely hot inside. After starting the vehicle, do not immediately turn on the air conditioning. It is best to open all windows for ventilation to release the hot air. Only after the interior temperature has dropped should you close the windows and turn on the air conditioning.

8

5

Share

What is the reason for tool marks on the screws connecting the center console to the door in a new car?

Tool marks on the screws connecting the center console to the door in a new car indicate that the door has been removed. All screws should be tightened once, and this could be a sign of the car being an accident vehicle. Definition of an accident vehicle: An accident vehicle refers to a vehicle that has suffered damage due to non-natural wear and tear, resulting in a decline in mechanical performance and economic value. Generally, an "accident vehicle" refers to a vehicle with structural damage. Additionally, flood-damaged cars and fire-damaged cars also fall under the category of "special accident vehicles." Methods to identify an accident vehicle: Methods to identify an accident vehicle include exterior inspection, light inspection, checking insurance records, and examining the interior. Conditions for quick accident handling: The conditions for quick accident handling are no personal injuries, no disputes among the parties involved regarding accident liability, the ability to drive the accident vehicle, all parties involved having vehicle insurance, and the willingness of the parties to proceed to a designated location for damage assessment.

15

4

Share

How many invoices are there when picking up the car?

There are 3 invoices when picking up the car. Check for any paint defects: When the car leaves the factory, the paint surface is smooth and flawless, as new cars undergo inspection before leaving the factory. However, during transportation from the manufacturer to the 4S store, the car may suffer scratches. Some dealers repaint these areas and sell them as new cars. Therefore, when picking up the car, it's essential to check if the paint surface is smooth and even. Any defects might indicate that it's a transport-damaged car that has been repainted. Check the production date: Cars that remain unsold for several months after production become inventory cars. It's important to check the production date when picking up the car. Check the buttons inside the car: Cars come with many features, and most functions are controlled by buttons inside the car. When picking up the car, it's crucial to test all buttons to ensure they work properly. The best approach is to try opening all buttons that can be operated to experience their functionality.

14

3

Share

Which region does the license plate 'Dong' belong to?

Currently, there is no license plate with the prefix 'Dong'. However, there is a Shandong license plate. The license plate codes for various regions in Shandong are as follows: Lu A is for Jinan City, Lu B is for Qingdao City, Lu C is for Zibo City, Lu D is for Zaozhuang City, Lu E is for Dongying City, Lu F is for Yantai City, Lu G is for Weifang City, Lu H is for Jining City, Lu J is for Tai'an City, Lu K is for Weihai City, Lu L is for Rizhao City, Lu M is for Binzhou City, Lu N is for Dezhou City, Lu P is for Liaocheng City, Lu Q is for Linyi City, Lu R is for Heze City, Lu S is for Laiwu City. The functions of a license plate are: 1. To number and register information for each vehicle; 2. To identify the region to which the vehicle belongs; 3. To trace the owner and registration details of the vehicle based on the license plate.

2

3

Share

What is the correct way to steer the wheel?

What Causes a Motorcycle to Have No High Voltage Spark When Starting?

Does Transmission Removal Affect the Car?

Can I Turn on Cool Air Without AC?

What is the reason for tool marks on the screws connecting the center console to the door in a new car?

How many invoices are there when picking up the car?

Which region does the license plate 'Dong' belong to?

What are the differences between domestic and joint-venture cars?

What is the valve clearance for the Chaochai 6102 engine?

What are the reasons for the increasingly heavy steering wheel of the Lavida?

How Does Insurance Cover a Water-Damaged Car?