What is the correct starting procedure for the XC60?

What's the issue when the gear indicator light flashes on a Golf 6?

It is likely that there is a gear malfunction, triggering a self-protection measure. It is recommended to restart the vehicle. If the issue persists, you should take it to a 4S shop or repair shop for inspection tomorrow. Other possible causes: There may be a malfunction or poor contact with the gear sensor; there could be an issue with the transmission; or the light wiring may have poor contact. Solutions for a flashing gear indicator light: Open the engine compartment and check if the wiring is aged or if rodents have damaged the wires; try shifting into each gear to see if it engages normally—if it does, the gear switch might not be properly installed; there could be an issue with the wiring from the gear switch to the computer, such as looseness or rust; problems with the transmission or battery can also cause the gear indicator light to flash. Remove the gear switch, disassemble it, and check if the copper contacts inside have excessive grease. Clean off the grease and reinstall the gear switch.

8

4

Share

Is the Corolla's timing belt a chain?

The Corolla uses a timing chain. The main function of the engine timing belt is to drive the engine's valve train, ensuring that the intake and exhaust valves open and close at the appropriate times to allow normal air intake and exhaust in the engine cylinders. Below are the steps for replacing the timing belt: 1. Remove the valve cover, detach the crankshaft pulley, and take off the timing chain cover. Rotate the crankshaft to align the first cylinder at top dead center, then secure the crankshaft by tightening the fixing screw. 2. Rotate the intake and exhaust camshafts. There are grooves at the rear of the camshafts; align these grooves evenly and insert the specialized tool. 3. Remove the old chain and install the new one. The crankshaft pulley does not have a keyway; during installation, align the round hole on the pulley with the groove on the timing chain cover. 4. The crankshaft position sensor is adjustable. Ensure it is properly adjusted without gaps during installation to avoid fault codes. Both the crankshaft sprocket and pulley can rotate freely.

19

2

Share

What are the differences between the 2018 and 2020 Toyota C-HR models?

The differences between the 2018 and 2020 Toyota C-HR models: 1. Exterior: The design of the 2020 model remains unchanged, continuing the original avant-garde and stylish look, which still stands out as the most distinctive SUV in its class. The most noticeable exterior difference is the removal of privacy glass, making it appear more transparent. 2. Interior: The original design is maintained, with the Leading Edition and higher versions upgraded to 10-way power-adjustable seats, while the Luxury Edition and Leading Edition now feature leather seats. All models have added a diamond-shaped SRS logo on the C-pillar, and all models still come standard with 10 SRS airbags. 3. Powertrain: The 2020 Toyota C-HR continues to offer only one engine option—the TNGA architecture-based Dynamic Force series 2.0L engine, with a maximum power output of 171 horsepower and peak torque of 203 N·m. Paired with the engine is a CVT transmission that simulates 10 gears, offering a 20% faster shift speed compared to traditional CVTs.

18

2

Share

What is the function of Prado KDSS?

The functions of Prado KDSS are as follows: 1. It is an adjustable damping stabilizer bar independent of the suspension system. During highway driving, it tends to be rigid, increasing the vehicle's lateral support force, reducing suspension travel, and improving driving stability. On off-road surfaces, it releases restrictions, increases travel, and enhances the vehicle's passing ability. 2. In KDSS conventional mode, when the vehicle is in a turning state, the outer suspensions of the front and rear wheels are compressed, and the inner suspensions are extended. This causes the stabilizer bar to twist, resisting body roll. The two pipelines connected between the two hydraulic pumps have no fluid flow, working like a normal suspension but effectively improving anti-roll capability. 3. When KDSS is in off-road mode, if one of the four wheels encounters an obstacle and is lifted, the suspension of the lifted wheel is compressed, and the stabilizer bar rises together with the hydraulic pump. Fluid flows between the two pipes of the front and rear hydraulic pumps, absorbing the twist of the stabilizer bar. Since the stabilizer bar does not twist, the suspension travel is larger than that of a normal suspension, and it can be adjusted according to different road conditions.

9

0

Share

Where is the location to add windshield washer fluid in the Bora?

The windshield washer fluid filling location for this model is at the lower left corner of the engine compartment. The windshield fluid filler is an upright tubular bottle neck. When you need to add windshield washer fluid, first open the car hood, then locate the windshield washer fluid filler at the lower left corner of the engine compartment, and finally open the blue cap to add the fluid. Windshield washer fluid is the common name for automotive windshield cleaning solution. Standard automotive windshield washer fluid consists of water, alcohol, ethylene glycol, activators, and corrosion inhibitors. It can clean various dirt on the windshield. When you need windshield washer fluid, simply press the windshield washer switch, and the wipers will spray the fluid to clean the windshield. When adding windshield washer fluid in winter, first use up the old fluid in the car, then add new antifreeze windshield washer fluid. Windshield washer fluid not used in winter can be used in summer, but not vice versa. Do not use tap water as a long-term substitute for windshield washer fluid, as it may cause the wipers to malfunction.

10

4

Share

How to Remove the Infotainment System in the 10th Generation Accord?

Here are the steps for removing the infotainment system in the 10th Generation Accord: 1. First, remove the plastic trim strip on the dashboard near the passenger side and the small plastic cover for the push-start button. 2. Next, remove the right-side panel, the right ventilation duct assembly, and the silver trim strip on the dashboard. 3. Finally, remove all the decorative panels around the gear shift, and the infotainment system removal will be complete. Below is some basic information about the 10th Generation Accord: 1. The 10th Generation Accord is a model under Honda, with body dimensions of 4893mm in length, 1862mm in width, and 1449mm in height, and a wheelbase of 2830mm. 2. In terms of appearance, the 10th Generation Accord features a bold design with a coupe-like style, a front face adorned with thick chrome trim that connects to the winged full-LED headlights on both sides.

8

4

Share

What is the correct starting procedure for the XC60?

What's the issue when the gear indicator light flashes on a Golf 6?

Is the Corolla's timing belt a chain?

What are the differences between the 2018 and 2020 Toyota C-HR models?

What is the function of Prado KDSS?

Where is the location to add windshield washer fluid in the Bora?

How to Remove the Infotainment System in the 10th Generation Accord?

What is the fuel consumption per 100 kilometers for the Toyota 4Runner?

Can the AWD system malfunction of Toyota Highlander be eliminated?

What is the purpose of Audi's Side Assist System?

What is the power output of the BYD Han EV charging station?