What is the correct parking procedure for an automatic transmission vehicle?

1 Answers
DelEleanor
07/29/25 6:15pm
Automatic transmission vehicle correct parking procedure is: 1. First press the brake, then pull up the handbrake; 2. Shift the gear to P position; 3. Slowly release the foot brake and then turn off the engine. Automatic transmission usually refers to the automatic gear shifting mechanism of a car. When driving, the control system of the automatic transmission automatically selects the appropriate gear based on the engine speed and load, replacing the driver's subjective judgment of timing and gear shifting operation. Automatic transmission is different from manual transmission. The former connects and transmits power through a soft connection, which is the torque converter. Automatic transmission does not have the clutch plate of manual transmission, so special attention is needed during operation. Otherwise, over time, it may cause problems such as overheating of the transmission temperature and insufficient power connection due to certain wear and tear.
Was this review help?
12
0
Share
More Forum Discussions

What grade of engine oil is used for the Changan CS15?

The engine oil grade used for the Changan CS15 is SL 3.5L 5W-30 Great Wall brand mineral oil, or SN-grade 5W-30 Shell Helix mineral oil. You can also check the vehicle's oil change standards in the owner's manual. The Changan CS15 is a compact SUV under the Changan Automobile brand, with body dimensions of 4135mm in length, 1740mm in width, and 1630mm in height, and a wheelbase of 2520mm. The Changan CS15 is equipped with an EA15 high-efficiency engine independently developed by Changan Automobile, with a maximum power output of 78.5kW, a maximum speed of 5500rpm, and a maximum torque of 145Nm.
8
2
Share

Why is the engine coolant level too low?

The main reasons for low engine coolant level include: malfunction of the water temperature gauge and its circuit, damage to the water temperature sensor, thermostat valve stuck open, failure of the louver to close the temperature control switch, fan motor circuit malfunction causing the fan to run continuously, or failure of the silicone oil clutch in vehicles equipped with a silicone oil clutch fan. The cooling system operates by circulating coolant through a water pump to carry heat away from the engine, achieving a cooling effect. If the engine coolant level is too low, it will result in the inability to circulate and dissipate heat, potentially leading to engine damage. Coolant is an essential part of a car's engine, circulating within the engine cooling system to remove excess heat generated during engine operation, ensuring the engine operates at the correct working temperature.
2
0
Share

How to Turn Off the Anti-Skid Function in Focus?

Method to turn off the anti-skid function in Focus: Disable it in the settings of the trip computer menu. Click on the "Driver Assistance" option in the menu settings and turn off the anti-skid function. Alternatively, you can use the buttons on the steering wheel to access the vehicle settings and disable the traction control system. The anti-skid system in cars includes derivatives such as the Electronic Stability Program (ESP), Traction Control System (TCS), Anti-Slip Regulation (ASR), and Vehicle Dynamic Control (VDC). The Focus is a compact car under the Ford brand, equipped with three types of engines: a 1.0-liter turbocharged engine, a 1.5-liter turbocharged engine, and a 1.5-liter naturally aspirated engine.
11
4
Share

What are the corresponding speeds for gear shifting in Subject 3?

Shift to 2nd gear when the speed is 10-20 km/h, shift to 3rd gear when the speed is 20-30 km/h, and shift to 4th gear when the speed is 30-40 km/h. The operation techniques are as follows: 1. Test requirements: Perform corresponding gear shifting operations according to the voice prompts of the test system. 2. Upshifting requirements: When upshifting, the action should be quick and gentle, the gear selection should be accurate, do not look down at the gear, and do not coast in neutral. Before upshifting, check the left and right rearview mirrors to ensure road safety, release the accelerator with your right foot first, press the clutch with your left foot, shift to the appropriate gear, then slowly release the clutch while gently pressing the accelerator to increase speed. 3. Downshifting requirements: Before downshifting, check the left and right rearview mirrors to ensure road safety. For example, when downshifting from 3rd gear to 2nd gear, release the accelerator (or press the brake) when the speed is 30 km/h, and shift to 2nd gear when the speed slowly drops to 20 km/h. 4. Gear and speed matching: During driving, keep the gear matched with the speed. Shift to 1st gear when the speed is 0-10 km/h, shift to 2nd gear when the speed is 10-20 km/h, shift to 3rd gear when the speed is 20-30 km/h, and shift to 4th gear when the speed is 30-40 km/h.
12
3
Share

How to Reset the Maintenance Reminder for Volkswagen?

Method to reset the maintenance reminder for Volkswagen: Turn off the ignition switch, press the clock adjustment button SET while turning on the ignition switch, release the SET button, press the SET button once more, turn off the ignition switch and then turn it on again to check if it has been reset. If not, the process must be restarted. Car maintenance refers to the preventive work of regularly inspecting, cleaning, supplying, lubricating, adjusting, or replacing certain parts of the car, also known as car servicing. Taking the Bora as an example, in terms of appearance, this car adopts the Volkswagen family-style front face design, with distinctively layered headlights featuring a wing-type design, giving it a strong three-dimensional feel. The rear design has changes in the outline and light clusters compared to the current model, and the body lines have become more fluid.
8
1
Share

Where is the car engine coolant located?

Car engine coolant is located in the coolant reservoir on the right side of the engine compartment. Coolant is also known as antifreeze, which prevents the coolant from freezing and cracking the radiator or damaging the engine cylinder block when the car is parked in cold seasons. Precautions for using car engine coolant: 1. Different types of antifreeze cannot be mixed; 2. Do not open the radiator cap or drain valve immediately after driving; 3. When replacing the coolant, be sure to completely remove the old antifreeze and thoroughly clean the radiator. Steps to replace car engine coolant: 1. Unscrew the radiator cap and open the radiator drain valve to release the antifreeze; 2. Flush the engine cooling system; 3. Add new antifreeze when the engine is cool, filling it up to the maximum mark on the radiator.
6
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.