···
Log in / Register

What is the correct method for pulling over to pick someone up?

3 Answers
AylaAnn
09/08/25 5:01am
Turn on the right turn signal, then pull over to the side of the road, preferably staying within 30cm of the curb. If stopping for an extended period, place a warning triangle behind the vehicle. For short stops, turn on the hazard lights to alert other drivers and pedestrians.
Was this review help?
6
3
Share
Bernice
09/20/25 3:41am
When picking up someone by the roadside, I prioritize safety above all. Choosing an open and secure parking spot is crucial, such as avoiding curves, intersections, or areas with no-parking signs. Slowly pull over to the curb, positioning the car as close to the sidewalk as possible. Remember to activate the right turn signal in advance to alert vehicles behind you of your intention to stop. After parking, it's advisable to turn on the hazard lights to enhance visibility. Simultaneously, carefully check the surroundings for any approaching vehicles or pedestrians using the rearview and side mirrors, especially motorcycles and bicycles, which can easily appear in blind spots. Then, quickly exit the vehicle to pick up the person without delay. I also remind passengers to safely enter the car and close the door properly. When departing, first activate the left turn signal, thoroughly check the rearview and side mirrors to ensure no vehicles are approaching, and then slowly pull away. The entire process should be smooth and orderly, avoiding sudden braking or acceleration. After all, accidents often happen in an instant, especially at night or on busy roads.
Was this review help?
16
4
Share
Expand All
KeiraLynn
11/03/25 4:04am
I often pull over to pick up my family during rush hour. Choosing an easier-to-park spot is the most convenient. First, slow down and find a location that's not a bus stop or fire lane, then pull close to the curb and stop. Turn on the right turn signal to let other drivers know you're parking. After stopping, check the rearview mirror to ensure safety before quickly opening the door to pick up passengers. I usually glance at the rear window for a few seconds while waiting, just in case a car suddenly approaches. After picking up, be swift to avoid blocking traffic for too long. Then, gently press the accelerator to leave, remembering to signal left before merging back into the lane. If there are cameras or no-parking signs nearby, extra caution is needed. In the city, this approach saves time and reduces risks.
Was this review help?
8
5
Share
Expand All
More Forum Discussions

Will ETC Malfunction Due to Prolonged Sun Exposure in Summer?

ETC will not malfunction due to prolonged sun exposure in summer. The ETC device was designed with harsh environments, including extreme summer heat, in mind. The power supply of the ETC device mainly relies on solar energy. If the ETC device is placed in a shaded area for an extended period, it may lead to insufficient battery power. Precautions for using ETC: The ETC transaction sensing range is 8 meters. When the vehicle in front stops, to prevent the vehicle in front from having a faulty ETC device or no ETC device at all, maintain a distance of more than 10 meters to avoid automatic sensing and paying for the vehicle in front. The speed limit for ETC lane recognition is 20km/h. If the speed is too fast, the vehicle's device information cannot be read, leading to a failed transaction. Unauthorized removal or movement of the OBU device, detachment or loosening of the ETC electronic tag, etc., will cause the electronic tag to fail. It can be sent to the bank where the ETC card was issued or the highway service office for inspection. If the loosening or detachment is not due to human factors, it only needs to be reactivated. When using a debit card bound to ETC, insufficient balance will also lead to a failed transaction. Follow the guidance of on-site staff to use the manual MTC lane, paying with cash or card. Poor sensing due to overly thick car windshields. This is especially important for vehicles that have had their windshields replaced after an accident or for those who have modified their front windshields.
5
4
Share

Does the Tire Pressure Monitoring System Need to Be Reinstalled After Changing Tires?

After changing tires, the tire pressure monitoring system needs to be reinstalled. The tire pressure monitoring, also known as tire pressure learning, involves a pressure sensor installed in each tire. These sensors transmit the tire pressure wirelessly to the vehicle's tire pressure control system, allowing the car's data display to show the pressure of each tire at its specific location. There are three commonly used methods for tire pressure monitoring: Direct Tire Pressure Monitoring: Direct tire pressure monitoring devices use pressure sensors installed in each tire to directly measure the tire's air pressure. The pressure information is transmitted from inside the tire to a central receiver module via a wireless transmitter, and the data for each tire's pressure is displayed. The system automatically alerts the driver when the tire pressure is too low or if there is a leak. Indirect Tire Pressure Monitoring: When the pressure in a tire decreases, the vehicle's weight causes the rolling radius of that tire to become smaller, resulting in a faster rotation speed compared to the other wheels. By comparing the differences in rotation speeds between the tires, the system monitors the tire pressure. Indirect tire pressure warning systems essentially rely on calculating the rolling radius of the tires to monitor pressure. Introduction to Tire Pressure Monitoring System (TPMS): This system combines the advantages of the two aforementioned methods. It is equipped with direct sensors in two diagonally opposite tires and includes a 4-wheel indirect system. Compared to using only direct systems, this hybrid approach reduces costs and overcomes the indirect system's inability to detect low pressure in multiple tires simultaneously. However, it still cannot provide real-time pressure data for all four tires as effectively as a direct system.
8
5
Share

What does the Audi MAX button mean?

Audi MAX button means the maximum cooling setting for the car air conditioning. Function of the MAX button: When the A/C cooling switch is turned on and MAX is activated, the air conditioning will operate at its strongest cooling capacity with the blower at maximum output. Its purpose is to rapidly lower the temperature inside the vehicle. Other meanings of MAX: The term MAX appears not only on air conditioning control buttons but also on various fluid reservoirs in the engine compartment. Here, MAX similarly indicates "maximum" or "highest" level, sometimes simply represented by the letter M.
16
0
Share

What Are the Reasons for Loud Noise When Accelerating?

The excessive noise when accelerating may be caused by an overheated engine or clogged internal engine valves. Below is a detailed explanation of these two causes: 1. Overheated Engine: If the engine temperature is too high, the cooling system may fail. In this case, the cooling system should be checked promptly. If the cooling system malfunctions, the vacuum tube may rupture, leading to a blocked exhaust pipe and resulting in loud noise when accelerating. 2. Clogged Internal Engine Valves: When the internal engine valves are clogged, it can easily cause loud noise when accelerating. In this situation, the cooling system should also be inspected to check if the coolant is functioning normally. Determining the cause of the fault depends on whether it is due to oil pressure issues or ignition problems.
1
3
Share

What are the three suspension modes of the old Touareg?

The three suspension modes of the old Touareg are Normal mode, Comfort mode, and Off-road mode. Introduction to Touareg suspension: The Touareg is equipped with a newly designed air suspension, which the manufacturer claims improves vehicle comfort and optimizes the sportiness and off-road capabilities of the new-generation Touareg. In addition to the standard and comfort modes provided by the air suspension, there are also an off-road lift mode that raises the vehicle by 25 mm and an off-road enhanced mode that raises it by 70 mm. Suspension design: When the vehicle speed exceeds 120 km/h, the air suspension automatically lowers by 15 mm. In loading mode, the single rear axle lowers by 40 mm for easier access to items.
3
5
Share

What Transmission Does the Volkswagen Bora Use?

Volkswagen Bora uses a 6-speed automatic transmission (6AT) with manual mode. Transmission Brand: The 6AT transmission is manufactured by Aisin, specifically the third-generation Aisin 6AT transmission. This transmission features dual planetary gear sets, which reduce fuel consumption during upshifts. It also incorporates an electronically controlled oil pump, enhancing fuel efficiency and making it more economical. Advantages of the 6AT Transmission: This transmission offers smooth shifting and is equipped with "Quick Shift Technology," ensuring clear and precise shift logic. A heat exchanger is installed on the torque converter, connected to the engine cooling system, allowing for rapid cooling and improved heat dissipation.
13
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.