Browse

Antiques Collectibles Apparel Baby Kids Items Books， Movies And Music Electronics Free Stuff Garden Outdoor Health Beauty Home Goods Home Improvement Supplies Musical Instruments Office Supplies Pet Supplies Sporting Goods Ticket Toys Games Transportation Others

Used Cars New Cars Others

Business Crafts Design And Web Events Home Improvement Legal Lessons Personal Pets Photography Repair And Technical Support Wellness Writing， Translation， And Transcription Others

Activities & Groups Artists & Musicians Classes & Lessons Events Friendship & Networking Lost & Found Rideshare Sports Teams Volunteers Travel & Travel Partners Skills & Language Swap Other

What is the complete process of the driving test simulation for Subject 3?

1 Answers

KimberlyDella

07/29/25 9:28am

Subject 3 driving test simulation involves the following steps: simulating nighttime driving scenarios with light usage test, starting the vehicle, changing lanes, driving straight, passing through pedestrian crossings, passing through school zones, passing through bus stops, passing through intersections, meeting oncoming vehicles, overtaking, making U-turns, and pulling over to park. Below are the precautions to take before starting the vehicle: 1. Turn on the turn signal: Before starting, you must turn on the turn signal and wait for it to flash for 3 seconds before moving the vehicle or steering wheel. After turning on the signal, you should also observe the road conditions; failure to do so will result in an immediate deduction of 100 points. 2. Check the doors: Before starting, you should also check if the doors are closed. Starting the vehicle with the doors open will also result in an immediate deduction of 100 points.

Was this review help?

10

4

Share

More Forum Discussions

What are the reasons for insufficient power in the Audi A4L?

The specific reasons for insufficient power in the Audi A4L are as follows: Fuel supply system: Due to the clogging of the fuel tank vent hole, partial blockage of the fuel tank switch, fuel filter, and the fuel line between the fuel tank and the carburetor, the required fuel supply cannot be met, resulting in an overly lean air-fuel mixture and weak engine performance. Ignition system: Incorrect ignition timing, such as advanced ignition, can cause premature combustion and detonation of the combustible mixture. Faults in the ignition system can lead to misfires or weak sparks from the spark plugs. Cylinder compression pressure: Severe wear of the piston, piston rings, and cylinder can increase the clearance between the piston, piston rings, and cylinder, reducing sealing performance. This leads to leakage from the cylinder head and a decrease in cylinder compression pressure.

What is the top speed of the Geely Xingyue L?

Geely Xingyue L has a top speed of 195 kilometers per hour. Power Output: The Geely Xingyue L is equipped with a 1.5T inline three-cylinder turbocharged engine, delivering a maximum power of 130 kW and a peak torque of 255 N·m. Paired with a 7-speed dual-clutch transmission, it achieves a top speed of 195 km/h. Exterior Design: The Xingyue L is positioned as a compact SUV, but with a length close to 4.8 meters and a wheelbase approaching 2.85 meters, it has already surpassed the traditional dimensions of a compact SUV. Even when compared to extended entry-level midsize SUVs like the Volkswagen Tiguan L, the Xingyue L holds comprehensive advantages.

Which Audi model features a five-cylinder engine?

Audi's five-cylinder models are as follows: Audi RS2: The Audi RS2 is often referred to as the 'instantaneous travel war machine.' The RS2 boasts 315 horsepower and immense grip, making it a beast in straight-line acceleration. Audi RS3: As a return to the Audi Quattro legacy, the RS3 features a 1-2-4-5-3 firing order, producing a sound reminiscent of Audi's rally cars from the 1980s. Audi TTRS: Audi's renowned 2.5-liter five-cylinder engine is housed under the hood of the first-generation TTRS, which also comes with a six-speed manual transmission. Audi Quattro: The original Audi Quattro retained the five-cylinder engine from its racing counterpart, bringing some rally charm to the streets, with output increased to 408 horsepower and 480Nm.

What Causes High Water Temperature in BMW 3 Series?

BMW 3 Series high water temperature reasons are as follows: Excessive engine carbon deposits: When there is too much engine carbon buildup, heat cannot dissipate completely under high load and high RPM conditions, leading to increased water temperature. Ignition timing too early: Early ignition timing can also cause engine temperature to rise during high-speed driving. Poor radiator cooling: It may also be caused by insufficient radiator cooling. It is recommended to check and clean engine system carbon deposits, and avoid excessive speed and overload operation while driving. Thermostat not opening wider: After turning on the AC, engine load increases, heat dissipation increases, and water temperature naturally rises. Most vehicles maintain original equilibrium temperature by increasing thermostat opening. If the car shows high water temperature, it means the thermostat isn't opening wider - you can check the thermostat.

How many points are deducted for rolling back on a slope during the parking test?

Starting with a rollback greater than 30 centimeters results in failing the test. The point deduction standards for slope starting are as follows: 1. If the vehicle's bumper is not aligned with the pole line and exceeds 50 centimeters forward or backward, the test is failed. 2. Starting with a rollback greater than 30 centimeters results in failing the test. 3. If the vehicle's bumper is not aligned with the pole line but does not exceed 50 centimeters forward or backward, 20 points are deducted. 4. If the vehicle body is not parked within 30 centimeters of the right sideline, 20 points are deducted. A rollback of less than 30 centimeters during starting results in a 20-point deduction. Always remember to use the turn signal when starting; failure to do so will result in immediate disqualification, and it's also important to ensure the engine does not stall.

What Causes High Shift RPM in the New LaCrosse?

High shift RPM in the New LaCrosse is caused by a faulty throttle position sensor, which sends incorrect signals indicating an open throttle. The ECU then enriches the fuel injection based on these signals. Replacing the position sensor will resolve the issue. Location of the Throttle Position Sensor: The primary function of the throttle position sensor is to detect whether the engine is in idle mode, under load, accelerating, or decelerating. It is essentially a variable resistor with several switches, installed on the throttle body. Function of the Throttle Position Sensor: When the throttle is in the idle position, the idle contact closes, sending an idle condition signal to the ECU. When the throttle is in any other position, the idle contact opens, outputting voltage signals corresponding to different throttle angles. The ECU uses these signal voltages to determine engine load and adjusts fuel injection accordingly or performs fuel cut-off control.

Trending Ranking

How to deactivate the Ford Focus anti-theft system?

Where is the reverse light wire of Volkswagen Touran?

Under what conditions does Toyota's automatic braking system activate?

What causes the grinding fan-like sound when starting the car on rainy days?

What is the Baojun LZW6477DWVYZ?

How to Activate the Defogging Function in Volkswagen Lavida?

Is the car's recirculation mode A or M?

What is the tire size of the BMW 530Li?

What Causes a Car to Stall Frequently?

What does 'Escape 4WD overheating temporarily invalid' mean?

More Forum Discussions

What is the fuel consumption of the Changan Honor?

Should You Wipe Your Car Dry After Rain?

What Causes the Jerking Sensation When Starting a Cold Car?

What is the horsepower of the Chery QQ3?

Help

Cookie

Cookie Settings

© 2025 Servanan International Pte. Ltd.