What is the Chinese meaning of AUX?

2 Answers
LeArcher
08/27/25 5:58am
AUX is an audio input interface. The basic working principle of the AUX interface is that after connecting to the AUX interface, the audio in electronic products can be connected to the car audio through the headphone jack and AUX interface, and the audio can be played in the car audio broadcasting facility. The USB interface can be inserted into a USB flash drive to play audio. When in use, insert one end into the AUX interface and connect the other end to a video player such as a mobile phone, MP3, or MP4. This allows you to listen to songs or niche music anytime and anywhere, not limited to car music CDs. However, if the playback device runs out of power, the music will also stop (the interface is generally a 3.5mm standard headphone jack). Aux is the abbreviation of Auxiliary, which is an additional signal line design. In general audio equipment, in addition to the formal output and input terminals, there are often several input and output terminals marked with Aux as backup connection terminals. When there are special applications, such as additional audio output or input, this type of terminal can be used. These backup terminals or lines, whether input or output, are collectively referred to as Aux. Function: The AUX port is an asynchronous port, mainly used for remote configuration, dial-up connections, and can also be connected to a MODEM through a transceiver. It supports hardware flow control. The AUX port and CONSOLE port are usually placed together because their respective applicable configuration environments are different. The AUX interface establishes a command-line connection method between the user and the device, enabling some operations that are usually impossible to complete in user mode, such as initialization, restoring initial configuration, and correcting abnormal user modes. It provides a fixed port for the device, which can be used as a standard asynchronous serial port with a maximum speed of 115200bit/s. Using the AUX interface, remote configuration and line backup of hardware products can be achieved. Note: When using the AUX interface, make sure to buy the correct connecting cable and avoid plugging the audio cable into the wrong port. It is best to follow the steps in the product's user manual when using the AUX interface. If you still don't understand, you can consult the product's official website or call for assistance.
Was this review help?
6
3
Share
VanDavid
09/09/25 4:53am
In cars, AUX is called an auxiliary input interface in Chinese. It's essentially a standard small jack that allows me to connect my phone or MP3 player to play music. As an audiophile, I often use it during long drives to play my phone's playlist—the sound comes out crystal clear, far better than radio, and without the lag or disconnection issues common with Bluetooth pairing. Sometimes, when camping in the suburbs, I even plug in a portable speaker for parties. It's worth noting that the jack can rust or loosen over time, so wiping it with a cloth regularly keeps it functioning well. Overall, the AUX interface makes driving life more enjoyable, especially for young people like me who love playing music on the go—just plug in and enjoy high-quality sound instantly.
Was this review help?
7
4
Share
Expand All
More Forum Discussions

Does Rain Affect a Car That Has Just Been Painted?

Rain does not have a significant impact on a car that has just been painted, although it may slightly affect the gloss. However, regular maintenance and waxing can help. Here are some relevant details: Precautions: It is best not to expose the car to rain within three days after traditional painting, and avoid washing the car within a week. If the car gets rained on right after painting, do not take immediate action. Wait for a week after painting to wash the car, then perform polishing. Check the polishing results—if any previous abnormalities are eliminated, that's ideal; if not, repainting may be necessary. Handling Methods: The best approach is to immediately move the car to a dry area. Do not touch the freshly painted surface. Once the paint is dry, use 1500-grit sandpaper with a sanding block and water to sand until the water marks are removed, then polish until the desired effect is achieved. If it starts raining during the painting process, stop immediately and move the car to a dry area. If only 1K base coat has been applied without clear coat, you can sand off the water marks and repaint. If clear coat has already been applied, do not repaint; wait for it to dry, then sand and repaint.
8
0
Share

How much gasoline does an 8-kilowatt generator consume per hour?

There is no precise measurement for the fuel consumption of an 8-kilowatt generator per hour, as fuel consumption generally depends on the generator's own fuel consumption rate and the size of the load. Below is relevant information about automotive generators: 1. Introduction: The automotive generator is the main power source of a vehicle. Its function is to supply power to all electrical devices while the engine is running normally and to charge the battery. Based on the three-phase stator winding of a conventional alternator, the number of winding turns is increased, and lead-out terminals are added, along with an additional three-phase bridge rectifier. At low speeds, the output is from the original winding and the additional winding in series, while at higher speeds, only the original three-phase winding provides the output. 2. Classification: Automotive generators can be divided into DC generators and AC generators.
19
2
Share

Is the Invoice Price of a Car the Naked Car Price?

Generally, the invoice price of a car is the naked car price. The relevant introduction of the naked car price is as follows: Introduction 1: The naked car price usually refers to the price of a commodity car without any non-standard accessories installed after leaving the factory (relative to the standard configuration when the car leaves the factory), which is the selling price at the 4S store. Introduction 2: The on-the-road price generally refers to all the expenses incurred by consumers from purchasing a car to licensing it. In addition to the manufacturer's suggested retail price (MSRP) of the vehicle, the on-the-road price also includes purchase tax, vehicle and vessel usage tax, car insurance fees, and licensing fees. If the car is purchased on loan, the on-the-road price also includes 4S store service fees, GPS fees, car loan interest, and other expenses.
1
2
Share

What is the assembly torque for the B12 engine?

B12 engine assembly is divided into four stages, with torques generally around 40N, 60N, 75N, and 90N. Below is relevant information about automotive engines: 1. Engine function: The car engine is the device that provides power to the vehicle, serving as the heart of the car, determining its power, fuel efficiency, stability, and environmental friendliness. 2. Materials used: Engine oil is a crucial material for the engine, containing various additives that effectively protect the engine's important moving parts and ensure its normal operation.
13
5
Share

What causes the ABS and anti-skid system to stop functioning in a Mercedes-Benz?

There are many reasons why the ABS and ESP may stop working. Issues such as tire pressure, cruise control problems, the brake HOLD function, control valves in the braking system, dynamic control high-pressure valves, inlet valves, outlet valves, brake cylinders, return pumps, active servos, non-original brake fluid, low-pressure accumulators, and more can all contribute to this problem. Here is some relevant information: For safety reasons, the ABR does not allow diagnostic tools to communicate with it while the vehicle is in motion. Although the vehicle is not currently moving, if the system mistakenly believes the vehicle is in motion, it may also prevent the diagnostic tool from communicating with the ABR. After careful consideration, the technician pointed to the wheel speed sensors as the likely culprit. If one or more wheel speed sensor signals are faulty, it can affect the system's ability to accurately determine the vehicle's driving status.
14
0
Share

What are the differences between Mercedes-Benz 200 and 300?

Mercedes-Benz 200 and 300 mainly differ in the following aspects: 1. Power: The Mercedes-Benz E200L is the low-power version, with a maximum power of 184 horsepower and a maximum torque of 300 Nm, while the Mercedes-Benz E300L adopts the high-power version, with a maximum power of 245 horsepower and a maximum torque of 370 Nm. The top speed of the E200 is 235 km/h, and the E300 is 250 km/h. The 0-100 km/h acceleration time for the E300 is 6.9 seconds, while the E200 takes 8.6 seconds. The fuel consumption for the E200 is 6.9L, and the E300 is 7.1L. The overall weight of the E300 is 30 kg more than the E200. 2. Configuration: The E300 additionally features a panoramic sunroof, electric steering wheel adjustment, memory steering wheel, memory function for electric seats, front seat heating, anti-glare interior and exterior rearview mirrors, and rearview mirror memory.
9
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.