What is the button below the wiper lever of the Audi A4L?

1 Answers
LaneLynn
07/30/25 5:22am
The button below the wiper lever of the Audi A4L is used to adjust the intermittent wiper timing. Here is some information about the automatic intermittent wiper settings: 1. The automatic intermittent wiper setting allows you to adjust the swing frequency, making the wiper speed vary according to the vehicle speed. When the wiper lever is set to the automatic intermittent position, the wiper will adjust its swing frequency based on the vehicle speed. 2. When the rain is not too heavy and the windshield is not densely covered with water, you can set the wiper lever to the low-speed swing position, marked as LO or LOW. When the rain intensifies and the windshield quickly becomes covered with water, significantly impairing visibility, you should switch the wiper to the high-speed swing position, marked as HI or HIGH, to continuously clear water from the windshield.
Was this review help?
4
5
Share
More Forum Discussions

What Causes the Noise When Braking?

There are several main reasons for noise when braking: 1. Excessive wear of the car's brake discs and brake pads. 2. Insufficient lubrication between the friction pads. 3. Issues with the installation of the brake pads, such as incorrect model or reversed installation. Additional Information: 1. The braking performance of a car depends on the brake pads, which generally consist of a steel plate connecting the heat insulation layer and the friction block. The heat insulation layer is made of non-heat-conductive materials, while the friction block is mainly composed of friction materials and adhesives. 2. Since brake pads frequently undergo friction, they are consumable items for cars. Lower-quality brake pads wear out faster and require more frequent replacement, so it is essential to choose high-quality brake pads. The car's braking system is a crucial part of ensuring safe driving, as it allows for emergency braking and prevents accidents like rear-end collisions.
1
2
Share

Why is there no guide line in the reversing camera of Baojun 510?

The trajectory line of the reversing camera comes from the reversing trajectory system. If you accidentally touch the settings in the menu bar and hide the trajectory line, you can readjust it in the settings. If you replace the original reversing camera with a wide-angle camera, there will also be no trajectory line, and you can only replace the camera again. The following is an introduction to the reversing camera guide line: 1. The wheel trajectory line is generally represented by two vertical solid or dotted lines, which are used to simulate the trajectory of the two rear wheels and will also deflect according to the steering wheel's rotation. The trajectory line of the reversing camera itself serves an auxiliary role, making reversing easier and ensuring safety during reversing. 2. If the reversing camera lacks the trajectory line, it naturally lacks a layer of protection, especially for beginners, the presence of the trajectory line is very necessary. Therefore, when purchasing, it is best to choose a reversing camera with a trajectory line. Of course, at the same time, you should also practice your reversing skills, which is the real key.
18
4
Share

Which brand does the Lynk & Co 03 belong to?

Lynk & Co 03 is a model under the Lynk & Co brand. Lynk & Co is a new-era premium brand jointly established by Geely Holding Group, Geely Auto Group, and Volvo Cars. Currently, Lynk & Co's mass-produced models include the Lynk & Co 01, Lynk & Co 02, and Lynk & Co 03. Below is a detailed introduction to the Lynk & Co 03: 1. The Lynk & Co 03 is the brand's first sedan following the popularity of the Lynk & Co 01 and Lynk & Co 02. In terms of engine design, the Lynk & Co 03 primarily uses three-cylinder engines across most of its lineup, except for the Pure Lite variant. The transmission options include a manual gearbox for the base model, while the rest of the models are equipped with a 7-speed dual-clutch transmission. 2. In terms of exterior design, the new car maintains the overall styling consistent with Lynk & Co's family design language. The frog-like split front headlight design remains unchanged, embodying the car's innovative concept of avant-garde, individuality, and boldness. Compared to the previous two generations, the Lynk & Co 03 features many standout design elements in its configuration.
4
5
Share

What is the horsepower of the Subaru BRZ?

The maximum horsepower of the Subaru BRZ is 200 hp, with a maximum power of 147 kW and a maximum torque of 205 N·m. Extended relevant information is as follows: 1. The new Subaru BRZ features a more sporty exterior design, equipped with 225/40-ZR18 Michelin Pilot Super Sport series tires, a reinforced chassis, and continues to be powered by a 2.0L naturally aspirated direct-injection engine. 2. Both a 6-speed manual transmission and a 6-speed automatic transmission are available. Additionally, in terms of acceleration time from 0 to 100 km/h: the 6-speed manual version takes 7.3 seconds, while the 6-speed automatic version takes 8.2 seconds. Regarding top speed, the 6-speed manual version reaches 230 km/h, whereas the 6-speed automatic version reaches 210 km/h.
20
3
Share

How to Replace the License Plate Light of Sagitar?

The method to replace the license plate light of Sagitar is as follows: 1. Prepare a flat-head screwdriver, then insert it into one side of the license plate light and gently pry to remove it. 2. Press the handle of the plug and remove the lamp holder. 3. The bulb is usually connected to the lamp holder; turn the connection clockwise to remove the bulb and replace it with a new one. Additional related information is as follows: 1. The Sagitar comes standard with ESP, electric speed-sensitive power steering, traction control system ASR, and anti-lock braking system ABS. These precise driving control configurations ensure the safety of the vehicle's occupants. 2. The Sagitar is available in 1.8t and 2.0 models, featuring laser welding technology and a 12-year anti-corrosion double-sided galvanized steel body. The transmission options include a 6-speed Tiptronic automatic manual transmission or a 5-speed manual transmission. It has high safety configurations, with standard features including 4 airbags, ASR traction control system, EDL electronic differential lock, MASR engine torque control system, ESP vehicle dynamic stability system, etc.
20
0
Share

How Many Cylinders Does the Enjoy Engine Have?

The Enjoy-2022-180TURBO-CVT full series is equipped with a 3-cylinder engine, model P10A5, with a maximum power of 90kW and maximum torque of 173Nm. The Enjoy-2022-Sharp Hybrid-1.5L full series features a 4-cylinder engine, model LEB42, with a maximum power of 80kW and maximum torque of 134Nm. The engines for the Enjoy are assembled domestically and produced by Dongfeng Honda. For daily maintenance of the Enjoy engine, the following methods can be used: Use lubricating oil of appropriate quality grade. For gasoline engines, select SD--SF grade gasoline engine oil based on the additional devices of the intake and exhaust systems and usage conditions. For diesel engines, choose CB--CD grade diesel engine oil according to mechanical load, with the selection standard not lower than the manufacturer's requirements. Regularly change the oil and filter. The quality of any grade of lubricating oil will change during use. After a certain mileage, performance deteriorates, leading to various engine problems. To avoid malfunctions, change the oil regularly according to usage conditions and maintain an appropriate oil level. When oil passes through the fine holes of the filter, solid particles and viscous substances in the oil accumulate in the filter. If the filter is clogged and oil cannot pass through, it may rupture the filter or open the safety valve, bypassing the filter and carrying contaminants back to the lubrication areas, accelerating engine wear and increasing internal pollution. Regularly clean the crankcase. During engine operation, high-pressure unburned gases, acids, moisture, sulfur, and nitrogen oxides from the combustion chamber enter the crankcase through the gap between the piston rings and cylinder walls, mixing with metal particles from component wear to form sludge. Small amounts remain suspended in the oil, while larger amounts precipitate, clogging filters and oil passages, making engine lubrication difficult and causing wear. Regularly use a radiator cleaner to clean the radiator. Removing rust and scale not only ensures normal engine operation but also extends the overall lifespan of the radiator and engine.
14
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.