What is the break-in period for the new Geely BinYue in kilometers?

1 Answers
StJocelyn
07/30/25 3:23am
Geely BinYue's break-in period is 3,000 kilometers, and its duration may vary depending on the frequency of car usage. Here are some precautions regarding the car break-in period: 1. The first maintenance should be performed when the car reaches 5,000 kilometers. After the first maintenance, the car will reach its most balanced state. 2. During the break-in period, avoid driving at high RPMs, as this increases the engine load, not only raising fuel consumption but also damaging the engine and reducing its lifespan. 3. For manual transmission cars during the break-in period, always fully depress the clutch pedal before shifting gears. Otherwise, it may damage the clutch plate and affect the transmission. 4. For automatic transmission cars during the break-in period, avoid shifting into neutral (N) gear. 5. Try to reduce the car's weight during the break-in period, keeping the load below 70% of the car's capacity to avoid excessive pressure on the tires and accelerated wear. 6. Use high-quality fuel during the break-in period to keep the engine in a good working condition, which not only speeds up lubrication but also extends the engine's lifespan.
Was this review help?
5
1
Share
More Forum Discussions

What Causes the High and Low Pressure of a Car's Air Conditioning to Be Equally High?

The reason for the high and low pressure of a car's air conditioning being equally high is insufficient refrigerant (Freon) in the AC lines or excessive addition of refrigerant oil, leading to a shortage of refrigerant. Here are the troubleshooting methods for car air conditioning: 1. Release excess refrigerant. 2. Replace the receiver-drier. 3. Perform a thorough vacuum and refill with refrigerant. 4. Clean or replace the condenser, and inspect the fan motor and its circuit. Compressor maintenance includes the following methods: 1. Check if the refrigerant is sufficient, measure the temperature difference between the inlet and outlet pipes of the drier, and inspect using a manifold pressure gauge. 2. Clean the air vents and remove dust and dirt inside the cabin. 3. Check if the refrigerant level in the AC system is normal. 4. Inspect the condition of the compressor belt.
15
3
Share

How to Release Windshield Washer Fluid in the Car?

The most direct method to release windshield washer fluid in a car is by spraying it out through the windshield wipers. Here are some related details about releasing windshield washer fluid: 1. If the windshield washer fluid is frozen, do not attempt to spray it. Running the windshield washer continuously for several seconds can cause the washer motor to overheat, leading to expensive repair costs. 2. If sunlight doesn't thaw the fluid, you can add some warm water (not boiling water) to the washer fluid reservoir. Once the fluid thaws, make sure to drain it completely to prevent it from freezing again. 3. Additionally, in colder weather, when adding windshield washer fluid to the car, if tap water has been previously added to the reservoir, ensure it is completely drained. Mixing windshield washer fluid with tap water can easily lead to freezing.
11
3
Share

How to Reset the Subaru Yellow Warning Light?

Subaru's yellow oil warning light may be caused by issues such as low oil level. To reset it, the underlying problem must be resolved. Check if the oil level is low or if the oil hasn't been changed on time and has deteriorated. Other related causes include: aging oil pump internal leakage, relief valve pressure release, bearing wear pressure release, or clogged filter. If any issues are detected, the vehicle should be sent to a workshop for inspection and repair. Additional relevant information is as follows: 1. The Subaru Forester's body dimensions are 4560mm in length, 1780mm in width, and 1700mm in height, with a wheelbase of 2615mm and a front-engine four-wheel-drive layout. 2. In terms of exterior design, this vehicle is equipped with high-brightness LED headlight assemblies, providing better visibility for the driver. The fog light area features more chrome trim for decoration, and the rear adopts C-shaped taillights.
6
4
Share

What is the model of the Tiggo 3 headlight s1?

Tiggo 3 headlight models are: low beam model H7, high beam model H1. Car headlights, also known as car front lights, car LED daytime running lights. Tiggo 3 headlight replacement method: 1. Unplug the power connector of the bulb. 2. After unplugging the power connector, remove the waterproof cover behind the bulb. 3. Remove the bulb from the reflector. The bulb is usually fixed by a wire clip, and some models of bulbs also have a plastic base. 4. Place the new bulb into the reflector, align it with the fixing position, pinch the wire clips on both sides and push them inward to secure the new bulb in the reflector. 5. Reattach the waterproof cover, plug in the bulb power, and the replacement operation is completed.
11
5
Share

What Causes Loud Engine Noise After Vehicle Maintenance?

Here are the reasons for loud engine noise after vehicle maintenance: 1. Using engine oil of different brands or specifications. 2. Excessive carbon buildup or overfilling of engine oil. 3. Incomplete removal of the original engine oil. 4. Changing the type of engine oil may cause noise. Here are solutions to reduce loud engine noise: 1. Use specialized equipment to perform a no-disassembly cleaning of the engine lubrication system. 2. Replace with the appropriate or higher-grade engine oil suitable for the vehicle model. 3. Add an appropriate amount of anti-wear additive for wear resistance and repair. 4. It is recommended to lift the vehicle and check if there is a heat shield between the exhaust pipe and the ground. The noise may be caused by aging of the heat shield, which can be resolved by replacement or removal.
19
4
Share

What kind of engine oil should be used for Toyota Crown?

Toyota Crown can use the following engine oils: 3M engine oil, 5W-30, and 5W-40 engine oils. 1. Mobil 1 EP, 5W20 or AFE engine oils. Other brands of 20-grade engine oils can also generally be used. Here are some relevant materials about engine oil: 1. It is essential to use engine oil with the appropriate quality grade, as this is key to ensuring the normal operation of the engine. 2. If the oil supply is delayed or no suitable oil is available, substitute oil can be used. 3. Choose oil with the appropriate viscosity. 4. When changing the oil, ensure that the waste oil is completely drained. 5. The gases that enter the crankcase from the combustion chamber are corrosive and can oxidize the engine oil, contaminating the engine. Therefore, it is necessary to maintain good crankcase ventilation. 6. Maintain the normal oil level height.
6
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.