···
Log in / Register

What is the best sound setting for the 2020 BMW 3 Series?

4 Answers
DeHope
07/24/25 11:50am
Ensure proper ventilation. Below is a detailed introduction to BMW: 1. Specific methods: The part of the audio system most affected by weather is the circuit board and some plastic components. The parameters of the electronic components on the circuit board vary with temperature changes. Therefore, if the car interior temperature is very high, it is recommended not to turn the audio volume too loud. Not only will the sound quality be affected, but it may also reduce the lifespan of the audio system. 2. Overview of BMW: BMW (Bavarian Motor Works), fully known in Chinese as Bayerische Motoren Werke AG, is a German luxury automobile brand. BMW's vehicle series include the i, X, Z, and pure numeric models (1, 2, 3, 4, 5, 6, 7, 8 series), as well as the M series (BMW's official high-performance modification division) based on improvements to these series. BMW was founded in 1916 and is headquartered in Munich, Bavaria, Germany.
Was this review help?
12
2
Share
DelJace
08/11/25 2:54am
As a car audio enthusiast, here's how I set up the sound on my 2020 BMW 3 Series: I pull the bass to +4 on the equalizer, keep the midrange around 0, and adjust the treble to +2, which gives great layering to both vocals and drum beats. Soundstage positioning is also crucial—I prefer setting the center point to the middle of the rear seats, allowing the subwoofer effect to fill the entire cabin. When using CarPlay, I opt for Apple Music's lossless format with all windows closed to maximize the factory sound insulation. Seat position also affects the sound, so I always fine-tune the soundstage after settling into my seat. This setup makes JJ Lin's vocals exceptionally clear, especially during my commute—it's incredibly relaxing! However, I recommend experimenting a few times, as everyone's ears perceive sound differently.
Was this review help?
8
1
Share
Expand All
Jenna
09/25/25 4:45am
To optimize the equalizer for the 2020 3 Series audio system, keep the bass below +4 to avoid muddiness. Midrange is best set between 0 to +1, while treble at +2 to +3 delivers optimal saxophone clarity. Source quality matters significantly—USB-played FLAC files outperform Bluetooth with noticeable differences. Cabin insulation directly impacts sound quality; I reduce bass by two notches on highways to counter tire noise. As a jazz enthusiast, I fine-tune settings per album while maintaining balanced frequency emphasis. BMW's system rewards meticulous adjustment—recommend calibrating in a quiet garage to craft your signature sound profile.
Was this review help?
19
4
Share
Expand All
VonNorah
11/08/25 6:53am
I've been driving the same car model for three years, and the core of the audio settings boils down to three points: bass +3, treble +3 on the equalizer, with midrange slightly adjusted to +1. Moving the soundstage positioning two notches forward can highlight vocals. When listening to Jay Chou, push the bass to +4, but for classical music, dial it back to +1. A special reminder: always keep the windows fully closed—even a slight gap can cause loss of low-frequency details. Using a USB drive for lossless music is far superior to Bluetooth; you'll know the difference once you try it! This setup works well for most Chinese pop music and is perfectly adequate for commuting.
Was this review help?
1
5
Share
Expand All
More Forum Discussions

What are the solutions for window glass rattling on bumpy roads?

The solutions for window glass rattling on bumpy roads are: 1. If it is caused by loose door screws or lifting brackets, simply visit a 4S shop and have the staff tighten the loose door glass; 2. If the window glass sealing strip is aged, it is recommended to replace it directly. If the rattling occurs in a new car, there is no need to replace the sealing strip—just evenly apply lubricant to the strip and then repeatedly raise and lower the window a few times to check if the rattling reduces; 3. If there are debris in the window glass guide rail, use tools to clean the debris in the guide rail. During the process of raising and lowering the window, dust and particles can easily be brought in, which may cause the window glass to vibrate and rattle. If dust and particles accumulate more and more, they can damage the lifting motor, leading to rattling or even affecting the lifting function.
11
0
Share

Can GL4 Transmission Fluid Be Replaced with GL5?

Whether to use GL-4 or GL-5 transmission fluid depends on the specifications in the transmission and vehicle manual. Generally, GL-4 transmission fluid is more suitable for household vehicles. Transmission fluid, also known as gear oil, is classified by the American Petroleum Institute (API) into performance levels such as GL-1, GL-2, GL-3, GL-4, GL-5, and GL-6, with corresponding level markings on the gear oil packaging. Below is a detailed introduction to transmission fluid: 1. Function: Transmission fluid is used to keep the car's gear system clean, providing lubrication to extend the life of the transmission components. It also offers effective lubrication at low temperatures and reduces fluid loss under harsh operating conditions. 2. Types: It is divided into automatic transmission fluid and gear oil. Automatic transmission fluid is specifically designed for automatic transmissions. Manual transmission fluid, commonly referred to as gear oil, is primarily made from petroleum-based lubricating oil or synthetic lubricating oil, blended with extreme pressure anti-wear agents and oiliness agents to form an important lubricant.
10
0
Share

How long after starting the car can you drive off?

For cold starts of small cars, it's advisable to wait about five minutes before driving off. Here's the relevant information: Reasons for needing to warm up the car: 1. Lack of lubrication: After the car has been parked for a long time, the engine oil flows back into the oil pan at the bottom of the engine. Therefore, when starting the engine after prolonged inactivity (such as overnight), the upper part of the engine is in a state without oil and lacks lubrication. It takes about 10 seconds after starting for the oil pump to circulate the oil to the parts of the engine that need lubrication the most, such as the pistons, connecting rods, and crankshaft. 2. Inability to effectively vaporize gasoline completely: Before the engine reaches its operating temperature (approximately between 90-110 degrees Celsius), the fuel system, due to the low temperature, cannot effectively vaporize the gasoline completely. When the gasoline is not vaporized and remains in a 'wet' liquid state, it is difficult to burn and start the engine.
19
0
Share

Do new cars need snow tires in the first year?

In the first year of a new car, it is necessary to decide whether to switch to snow tires based on the usage environment. Snow tires are specifically designed for winter driving conditions, ensuring driving safety and optimal vehicle performance in winter climates, regardless of whether the car is new or old. In China, regions like the three northeastern provinces, Inner Mongolia, Xinjiang, and Gansu replace their tires with snow tires annually. In snowy areas, the decision to use snow tires depends on specific usage conditions. Most original equipment tires on vehicles are all-season tires, which generally have mediocre winter performance and cannot guarantee good driving performance on ice and snow roads. Therefore, as long as the driving environment involves ice and snow roads, it is advisable to switch to snow tires.
18
2
Share

What is the H7/h6 fit?

H7/h6 is the tolerance fit code for mechanical components in the industry. H7 refers to the tolerance zone code for the hole it fits with, while h6 represents the tolerance zone code for the outer surface of the bearing (where the bearing acts as the shaft when fitting with the hole). The outer and inner diameter dimensions of the bearing vary, so while the tolerance zone H7/h6 is the same for different bearing sizes, the actual tolerance values differ. The numerical values of H7/h6 are related to the diameter—the larger the diameter, the larger the H7/h6 value, and vice versa. The functions of a tire are: 1. To transmit driving force, braking force, and steering force to enable vehicle operation; 2. To support the vehicle load; 3. To reduce and absorb vibrations and impact forces during driving, preventing severe vibrations from damaging automotive components. Methods for tire maintenance include: 1. Regularly checking tire pressure; 2. Periodically inspecting tires for bulges, cracks, cuts, punctures, or abnormal wear; 3. Removing foreign objects such as stones, metal pieces, or nails from tire treads; 4. Performing wheel alignment or tire dynamic balancing.
15
5
Share

How Does a Seat Belt Work?

Seat belts work by: 1. Tightening promptly to secure the occupant in the seat at the moment of an accident; 2. Releasing moderately, once the peak impact force has passed or when the occupant is protected by the airbag, to prevent rib injuries caused by excessive tension. Advanced seat belts are equipped with pre-tensioners and force limiters. When properly fastened, they distribute most of the stopping force across the chest and pelvis—areas of the body that are relatively strong. Since seat belts span a wide area of the body, the force is not concentrated in a small region, thereby minimizing potential injuries.
3
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.