What is the belt routing for the alternator on the older Audi A6 2.0T?

1 Answers
LaLondyn
07/28/25 4:46pm
Pull the alternator's main pulley shaft outward to facilitate subsequent belt installation. Properly align the position of the alternator's main pulley shaft, as incorrect alignment will affect the belt routing. Pull the alternator's two idler pulleys outward, also to facilitate belt installation.
Was this review help?
11
4
Share
More Forum Discussions

The Hazards of Coasting in Neutral on a Downhill Slope?

Coasting in neutral on a downhill slope can damage the transmission. The specific impacts are as follows: 1. Inability to supply oil normally: When an automatic transmission vehicle is shifted into neutral (N) while driving, the oil pump in the automatic transmission will not be able to supply oil normally for lubrication, causing the internal components of the transmission to heat up and leading to complete damage. 2. Increased fuel consumption: Coasting in neutral does not save fuel; sometimes it even consumes more. This is mainly related to the working mode of electronic fuel injection engines. Electronic fuel injection engines can determine the amount of fuel injection based on the computer program. If coasting in neutral is selected, the computer will put the vehicle into idle mode, and the engine will still inject fuel.
19
5
Share

What to Do About Severe Rear Tire Wear on the Outlander?

The severe wear on the rear tires of the Outlander is caused by excessive rear wheel camber deviation, which can be corrected through precise four-wheel alignment. Some models with independent rear suspension do not come equipped with factory-installed eccentric bolts for adjusting camber, requiring separate purchase during four-wheel alignment. Here are the main causes of tire wear: 1. Early wear on the central part (tread) of the tire: Overinflation. Properly increasing tire pressure can reduce rolling resistance and save fuel. 2. Excessive wear on both sides (shoulders) of the tire: Underinflation or prolonged overloading. Low pressure or heavy loads increase the tire's contact area with the ground, causing both sides to engage and wear prematurely. 3. Excessive wear on one side of the tire: Incorrect front wheel alignment. When the front wheel camber is too large, the outer edge wears prematurely; when it's too small or absent, the inner edge wears prematurely. 4. Severe abnormal wear on the inner side of the left rear tire and the outer side of the right rear tire: Non-parallel front and rear axles, with the right wheelbase exceeding the left beyond standard, or vice versa.
17
2
Share

What is the maintenance interval for the Mazda 6?

The maintenance interval for the Mazda 6 is every 5,000 kilometers or three months. There are two indicators for car maintenance: one is the time indicator, and the other is the mileage indicator, whichever comes first. Below are the details about car maintenance: 1. Minor Maintenance: Minor maintenance mainly involves changing the engine oil and oil filter. Engine oil, also known as engine lubricant, is referred to as the 'blood' of the engine. Its primary functions include lubrication, shock absorption, and buffering for the engine. Engine oil can be categorized into mineral oil, semi-synthetic oil, and fully synthetic oil, each with different effects and usage intervals. 2. Major Maintenance: Major maintenance involves a comprehensive inspection of the car and replacing the 'five oils, four filters, and three fluids.' The five oils include engine oil, power steering fluid, transmission fluid, clutch fluid, and brake fluid. The four filters are the air filter, oil filter, fuel filter, and cabin air filter. The three fluids are coolant, battery fluid, and windshield washer fluid.
5
3
Share

How to Cancel Cruise Control on Volkswagen Polo?

There are three methods to cancel the current cruise control speed: press the brake pedal; press the cancel button; or press the OFF button. This will deactivate the current cruise control. Below are precautions for using cruise control: 1. Rainy and snowy weather: Road surfaces are slippery, and road conditions change significantly, making cruise control unsuitable. Other complex road conditions are also not ideal for cruise control; it can be turned off or canceled in advance. 2. During normal cornering: Additional throttle is often needed to provide greater steering force. However, in cruise control mode, the vehicle automatically maintains a constant speed, with the throttle controlled by the onboard computer, which can pose risks during cornering. In such situations, cruise control is also not recommended.
8
1
Share

How many seats can a Class C driver's license drive?

C driver's license can drive vehicles with up to 9 seats. Among Class C driver's licenses, C1 is the highest level, allowing the driver to operate small passenger vehicles with up to 9 seats. According to the "Regulations on the Application and Use of Motor Vehicle Driver's Licenses" regarding the permitted vehicle types: The highest permitted vehicle type for a C1 driver's license is small and micro passenger cars, as well as light and micro trucks; light and micro special operation vehicles. Additional information: 1. Class C driver's licenses can be divided into: C1 (small cars), C2 (small automatic transmission cars), C3 (low-speed trucks), C4 (three-wheeled cars), C5 (small automatic transmission passenger cars for disabled people). 2. Small passenger cars generally refer to small vehicles carrying people, specifically small buses with a capacity of 2-9 people, usually including sports cars, sedans, and micro vans. Due to their compact size, these vehicles are very suitable for family and organizational use. They are generally distinguished from medium and large buses. The advantages of micro vehicles are their affordable price, convenient maintenance, and lower fuel consumption.
3
5
Share

What is kaweiauto?

kaweiauto is Kawai Auto. Here are the specific details about kaweiauto: 1. Types: Mainly produces light vehicles, buses, and special-purpose vehicles. 2. Technology: High-start entrepreneurship, high-tech establishment, and high-standard development. Leveraging its cutting-edge technological advantages and high-tech platform to develop the automotive industry, it is the largest automotive vehicle and body component manufacturing group in the region. 3. Group: The group covers an area of 2,500 acres, with an annual output value of 8 billion yuan, fixed assets of 5 billion yuan, and over 2,000 employees. It has established more than 1,000 automotive parts dealers nationwide, and its products are exported to more than 20 countries and regions, including Japan, South Korea, Thailand, Iran, and Russia. The group implements a talent strategy, with over 200 technical R&D personnel, adopting a multi-faceted integration of industry, academia, and research, and collaborates with institutions such as Shanghai Jiao Tong University, Changchun Automotive Research Institute Testing Center, Air Force Aviation Equipment Research Institute, and Armed Police Academy to create R&D teams for automotive vehicles, firefighting equipment, and automotive components.
13
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.