What is the battery model number for the Skoda Fabia?

2 Answers
Alyssa
07/25/25 5:08am
Skoda Fabia's dedicated car battery brand and model: GS56093; specifications: 12V 60AH. Below is a detailed introduction about the Fabia car: 1. Overview: The Skoda Fabia was born in 1999 and has been a bestseller in the European small car market since its launch. The Fabia Enjoy Special Edition shows no changes in appearance compared to the current model, with three body colors available: Latin Red, Electric Blue, and Jazz White. 2. Space: The new Fabia is 3993mm long, 1732mm wide, and 1487mm high, with a wheelbase of 2470mm. Compared to the 2014 Fabia, the new Fabia's body width has increased by 90mm, enhancing the lateral seating space inside the car.
Was this review help?
3
3
Share
DeSkylar
08/10/25 5:38pm
I've been driving a Skoda Fabia for several years, and mine is the 2015 model. The battery model it uses is 12V 54Ah, specifically Varta 544 or similar specifications. When I bought it, I asked at the 4S shop, and they mentioned that batteries might vary for different model years. For example, older models before 2010 might come with a 44Ah battery. Battery maintenance is crucial, especially in northern winters when starting issues often indicate it's time to check the battery voltage. A reliable voltage should be above 12.4V; if it's too low, it's time for a replacement. I've measured the voltage myself before—just using a multimeter, it's quite simple. When replacing the battery, don't cut corners; the size must match the original. Even a slight difference in length or width might prevent it from fitting properly, affecting starting performance. It's more reliable to visit a repair shop and have them test it—spending a little money can save you from bigger troubles.
Was this review help?
20
4
Share
Expand All
More Forum Discussions

What does the U0100 fault code mean when the car won't start?

It is related to the loss of communication with the engine control module. Here is the relevant introduction: U0100 fault code: The U0100 fault code, applicable to all automobile manufacturers, means Lost Communication With Engine Control Module (ECM)/Powertrain Control Module (PCM) A. Engine Control Module The engine control module, also known as the engine control unit (in some vehicles, the engine control module and transmission control module are integrated together and referred to as the powertrain control module), controls the operation of the entire engine. Its most important function is to control the optimal fuel injection amount and ignition timing of the engine. Another important function is to manage components responsible for exhaust emission control.
9
1
Share

What is the difference between Teana and Altima?

The seventh-generation Teana is named Altima in English, while all Teana models before the seventh generation were named Teana. Here is some extended information: Introduction: The seventh-generation Teana has dimensions of 4901 mm in length, 1850 mm in width, and 1450 mm in height, with a wheelbase of 2825 mm. The seventh-generation Teana is equipped with two types of engines: a 2.0-liter naturally aspirated engine and a 2.0-liter turbocharged engine. The 2.0-liter naturally aspirated engine has a maximum power output of 115 kW and a maximum torque of 197 Nm. This engine can deliver its maximum power at 6000 rpm and its maximum torque at 4400 rpm. It features continuous variable valve timing and direct fuel injection technology, and uses an aluminum alloy cylinder head and block. Extended: This engine is paired with a CVT transmission. The 2.0-liter turbocharged engine has a maximum power output of 179 kW at 5400 rpm and a maximum torque of 371 Nm at 4400 rpm. This engine is equipped with variable compression ratio technology and variable valve timing. It also features direct fuel injection technology and uses an aluminum alloy cylinder head and block.
5
1
Share

What does the VDC vehicle dynamic control system mean?

VDC is the Vehicle Dynamic Control (VDC) system. Its English name is Vehicle-Dynamics-Control, and the Chinese name is the vehicle dynamic control system. Here is relevant information: The Vehicle Dynamic Control (VDC) system is designed to improve the stability of a car while driving, but it cannot prevent accidents caused by sharp turns at high speeds or careless or dangerous driving maneuvers. When driving or turning on slippery roads, please reduce your speed and drive carefully. Function: When the car experiences wheel slippage, roll, or loss of tire traction, the VDC system will immediately intervene by reducing engine speed and purposefully applying braking control to individual wheels, ultimately guiding the car back onto the normal driving path, thereby avoiding the danger caused by loss of control.
2
0
Share

What transmission does the Volvo S60 use?

The transmission brand used in the Volvo S60 is Aisin. Established in 1969, Aisin is a world-renowned professional research, development, and manufacturer of automotive automatic transmissions. In the field of automotive automatic transmissions, Aisin's products hold the highest market share globally. The Volvo S60 is equipped with an 8-speed automatic manual transmission. Vehicles with automatic manual transmissions feature both automatic and manual modes, and the 8-speed automatic manual transmission offers 8 levels of gear shifting. When the car is switched to manual mode, the 8th gear is the highest gear. When using the Volvo S60's transmission in daily driving, pay attention to the following points: Do not delay replacing the transmission oil for extended periods. Although many modern vehicles come with maintenance-free transmission oil, "maintenance-free" does not mean it never needs replacement. Prolonged failure to replace the transmission oil can lead to damage to internal components such as bearings and the transmission housing. Avoid coasting in neutral for long durations. While driving manual transmission vehicles, many experienced drivers tend to coast in neutral. However, for automatic transmission vehicles, coasting in neutral can cause the transmission to overheat, and shifting back into Drive (D) mode may result in noticeable jerks. Never shift into Drive (D) or Reverse (R) before the vehicle comes to a complete stop. Many drivers, aiming to showcase "smooth" operation, engage the opposite gear before the car fully stops. This practice significantly damages the transmission gears and may lead to gear grinding or other malfunctions over time. Avoid frequently climbing steep slopes in Drive (D) mode. When tackling steep inclines, automatic transmission vehicles often overheat due to high loads or shift prematurely, resulting in insufficient climbing power. In such cases, use manual mode to lock in lower gears or switch to sport mode to protect the transmission. Do not tow the vehicle over long distances. If an automatic transmission vehicle breaks down, use a flatbed tow truck to transport it while the transmission is in Neutral (N). Avoid using tow ropes or dragging the vehicle directly, as this can cause severe damage to the transmission.
1
2
Share

What does tripkm mean?

tripkm refers to the mileage. It mainly indicates the mileage before the current stage is reset to zero. If you want to restart recording the mileage, press the trip button to reset the current stage to zero. The speedometer displays the vehicle's speed in km/h (kilometers per hour). The car odometer actually consists of two meters: one is the speedometer, and the other is the odometer. The car odometer is usually located directly in front of the driver's position. Purpose of trip: It is generally used to record and calculate the actual fuel consumption of the vehicle, and can also serve as a record of the mileage for planned routes. How to calculate fuel consumption: During the first full refueling (note: it must be a full tank), simultaneously reset the trip mileage to zero, then drive normally to accumulate mileage. When refueling next time, the current mileage (referred to as B) will be the amount of fuel added next time (referred to as A, which must be a full tank). Then, the actual fuel consumption is calculated as the amount of fuel added A ÷ the current mileage B. Repeat this process for subsequent refuelings, and the more times you refuel, the more accurate the average actual fuel consumption calculation will be.
4
4
Share

What brand is Vespa?

Vespa is a brand of scooter products, initiated by Enrico Piaggio of the Piaggio family and designed by engineer Corradino D’Ascanio. It began civilian mass production and sales in Italy in 1946. Piaggio decided to name it "Wasp," which in Italian translates to "Vespa" in English. Historical Background: During World War II, many Italian industries were connected to national arms manufacturing. After being bombed by the Allies, many manufacturers' factories were destroyed. However, the Piaggio family managed to revive their family economy through aircraft manufacturing. Development History: In 1951, British motorcycle manufacturer Douglas began producing Vespa under license (having introduced Piaggio's models in the previous two years). Although Douglas-produced Vespas accounted for only a small portion of Vespa's total sales, they accelerated Vespa's global popularity.
12
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.