What is the battery model for the Kia K4 key?

1 Answers
EloiseLee
07/30/25 12:40am
The battery model for the Kia K4 key is a CR2032 coin cell. The steps for key disassembly and battery replacement are as follows: 1. Separate the key by gently prying open the back cover with a flat-head screwdriver and removing it; 2. Separate the upper and lower panels, then remove the old battery; 3. Install the new battery by placing it into the slot; 4. Reassemble the panels and the key. When installing the battery, note that the positive side should face downward. The Kia K4 is a mid-size sedan from Dongfeng Yueda Kia, with body dimensions of 4720mm in length, 1815mm in width, and 1465mm in height, and a wheelbase of 2770mm.
Was this review help?
4
5
Share
More Forum Discussions

What's the Difference Between 2.5 and 2.0T?

Here are the differences between 2.5 and 2.0T: 1. Difference One: Displacement varies. (1) 'L' indicates the engine is an inline, naturally aspirated engine. (2) 2.0T denotes a displacement of 2.0 liters with turbocharging. (3) The role of turbocharging is primarily to increase the engine's air intake volume, thereby enhancing the engine's power and torque, making the car more powerful. 2. Difference Two: Power differs. (1) Compared to a 2.5 naturally aspirated engine, a 2.0 turbocharged engine delivers more immediate and aggressive acceleration. (2) For a 2.0T turbocharged engine, after boosting, the power output can reach levels comparable to a 2.8L or even higher engine. 3. Difference Three: Acceleration varies. (1) The turbo can reach its optimal state around 1500 to 2000 RPM, achieving peak torque. (2) For a naturally aspirated engine, reaching peak torque requires higher RPMs, typically between 5000-6000 or even higher.
17
5
Share

Can You Open the Car Door Underwater?

If a vehicle accidentally falls into water, it is difficult to open the car door for a period of time after the vehicle is submerged. Here is relevant information: 1. Reason: When the vehicle first enters the water, there is a large amount of air inside the car, while the outside is water. The pressure difference between the inside and outside is significant, making it difficult to open the door directly, thus preventing a quick escape. Only after a substantial amount of water enters the car, reducing the air and equalizing the pressure difference, does it become easier to open the door. 2. Precautions: A car will not sink immediately after falling into water, allowing a window of one and a half minutes or even two minutes to escape through the door or window before sinking. Even if the car sinks to the bottom, there are ways to escape, as it may take up to half an hour for the cabin to fill with water. The exact time depends on whether the windows are open, the body is sealed, and the depth of the water. The deeper the car sinks, the greater the water pressure, and the faster the cabin fills with water.
16
5
Share

What Causes the Malfunction of Audi's Low Beam and High Beam?

Left light grounding is loose, causing an open circuit; it could also be an issue with the lighting control module; or a problem with the combination switch, or communication failure between the two. Below are specific explanations: 1. All lights are on: indicates a malfunction in the dimmer switch. 2. If the high beam is on but the low beam is off when connected: the fault lies between the dimmer switch and the headlight or between the dimmer switch and the low beam. 3. If the high beam of the headlight does not turn on: check if the high beam indicator is on. If it is, the fault is between the terminal block and the headlight; if not, the fault is between the terminal block and the dimmer switch. 4. If only one headlight is on and the other is off: it may be due to a burnt-out filament, an open circuit in the wiring, or poor grounding (dim headlight).
6
5
Share

What are the reasons why the driver's door of the Audi Q5 cannot be opened from the outside?

The door cannot be opened due to a malfunction of the internal components of the car door. If the car door components are faulty, it is necessary to promptly go to the car's 4S store or a repair shop to inspect the door or replace the components. The following are the precautions for use when getting out of the car: 1. Observe whether there are vehicles approaching from behind: Before opening the door, observe the left rearview mirror to confirm whether there are vehicles approaching from behind. For passengers on the left side of the rear seat, the driver should be asked to help observe the situation behind before opening the door to confirm safety. 2. Do not push the door open all at once: Open the door slightly to confirm from the external rearview mirror that there are no vehicles coming from behind before fully opening the door. Do not push the door open all at once, but first open it slightly. This allows drivers of motorcycles and non-motor vehicles approaching from behind to know in advance that the door is about to open, so they can avoid it.
15
2
Share

What does the tire high pressure warning mean?

Tire pressure display belongs to active tire pressure monitoring, which can directly show the current tire pressure, while tire pressure warning belongs to passive tire pressure monitoring. The following are detailed introductions: 1. Direct tire pressure monitoring: A gas pressure sensor is installed inside the tire, and a wireless transmitter is used to send the signal to the central receiving module. After processing, the specific value is displayed on the instrument. When the pressure is insufficient or there is a difference, the monitoring warning light will turn on. 2. Indirect tire pressure monitoring: The wheel speed difference is used to determine tire leakage. When a tire leaks, the weight of the vehicle will reduce the rolling radius of that wheel, causing its speed to be faster than other wheels. By comparing the speed difference between tires, it can determine whether the tire is under-inflated, and the tire pressure monitoring warning light will turn on.
7
1
Share

What are the gears of the BMW X3 automatic transmission?

BMW X3 automatic transmission gear introduction is as follows: 1. P (Parking gear): This gear is usually located at the top of the gear lever. It should be engaged when parking for a long time. If the parking gear is not engaged when the engine is turned off, it should be engaged before starting the vehicle next time. 2. R (Reverse gear): This gear can only be engaged when the car is completely stopped. 3. N (Neutral gear): The hydraulic torque converter is in an idling state, and power cannot be transmitted to the planetary gear. The neutral gear is used for short-term parking. 4. D (Drive gear): The automatic transmission works automatically during driving, and the driver only needs to control acceleration and deceleration. 5. S (Sport gear): In sport mode, the transmission can shift freely. During driving, the gear lever can be directly pushed into the S gear, which is usually used for climbing and overtaking.
12
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.