What is the battery model for the Highlander car key?

1 Answers
OEllie
07/29/25 7:36pm
Highlander car key battery model is CR1620. Car key battery models: Car remote keys use button batteries, mainly CR2016, CR2025, and CR2032. For specific models used in each vehicle, owners can refer to the battery model in the user manual for replacement. Highlander key battery replacement method: On one side of the car key, locate the notch; use a screwdriver to pry open the key; after opening, you will see the round button-shaped battery, remove it; install the new battery you prepared; then snap the key shell back together, and the battery is successfully replaced.
Was this review help?
14
5
Share
More Forum Discussions

What are the penalties for speeding between 10% and 20% over the speed limit on highways?

For speeding between 10% and 20% over the speed limit on highways, 3 demerit points will be recorded and a fine will be imposed; for exceeding the speed limit by more than 20% but less than 50%, 6 demerit points will be recorded and a fine will be imposed; for exceeding the speed limit by more than 50%, 12 demerit points will be recorded and a fine will be imposed. When driving small passenger cars on highways, the speed must not exceed 120 kilometers per hour, while other motor vehicles must not exceed 100 kilometers per hour. Speeding refers to the situation where a driver operates a vehicle at a speed exceeding the limits set by laws and regulations. A highway refers to a road designed to accommodate an average daily traffic volume of at least 25,000 small passenger vehicles, exclusively for high-speed divided-lane travel by motor vehicles, with full access control.
20
5
Share

What is the electricity consumption per 100 kilometers for new energy vehicles?

The average electricity consumption per 100 kilometers for new energy vehicles is 15.95 kWh. System power consumption: Systems such as the vehicle's steering, lighting, audio, ventilation, and heating all consume electrical energy, accounting for about 6% to 12% of the total energy consumption of an electric vehicle. Frequent braking and starting: In congested traffic conditions, frequent braking and starting of gasoline vehicles can cause the motor current to rise repeatedly, which is several times higher than during normal operation, thus consuming a significant amount of electricity. Rapid acceleration and braking: During rapid acceleration and braking, the motor operates at maximum power output, which not only consumes more electricity but also affects the motor's lifespan. Excessive load: The weight of the electric vehicle itself and the intensity of the load also affect the vehicle's range. The greater the motion resistance, the faster the electricity is consumed.
15
5
Share

Is it necessary to use 95-octane gasoline?

Whether it is necessary to use 95-octane gasoline depends on the specific vehicle model. Explanation of gasoline grades: Although higher-octane gasoline offers better anti-knock performance and power, vehicles designed for lower-octane fuel should not blindly opt for higher-octane gasoline. Higher octane ratings are more suitable for engines with larger compression ratios, while engines in vehicles that use lower-octane fuel typically have smaller compression ratios. Using higher-octane gasoline in such engines may increase knocking. Avoid mixing different grades: Different grades of gasoline should not be mixed, such as blending 98 and 95-octane gasoline. Long-term use of mixed fuels may have adverse effects on the engine, potentially leading to issues like carbon deposits and increased fuel consumption.
3
2
Share

What Causes Poor Motorcycle Acceleration?

Here are the specific reasons for poor motorcycle acceleration: Incorrect Engine Oil Level: If too much engine oil is added, the crankshaft will operate with more difficulty, requiring greater power to drive, resulting in poor acceleration. If too little engine oil is added, components will not receive sufficient lubrication, leading to reduced power. Mismatched Engine Oil: If the viscosity is too high, the crankshaft will have difficulty operating. If the viscosity is too low, the engine will not adapt well to the oil, leading to noise. It is recommended that owners replace the engine oil and add new oil according to the standards specified in the vehicle manual. Clogged Oil Filter or Severe Carbon Buildup: When changing the engine oil, the oil filter should generally be replaced as well. If the oil filter becomes clogged and is not replaced in time, the oil will bypass through the relief valve, causing reduced vehicle power and increased engine wear.
7
0
Share

Why Does Goodyear Tire Experience Peeling?

Here are the specific reasons why Goodyear tires experience peeling: Working Pressure: Both excessively high or reduced working pressure during tire usage can affect the tire's lifespan. Therefore, tire pressure is an issue that car owners need to pay attention to. Tire Load: Tires produced by reputable manufacturers have a load index. In cases of overloading, the greater the vehicle's load, the shorter the tire's lifespan. Driving Speed: Tires from reputable manufacturers have a speed rating index. Tires driven at excessively high speeds are more prone to peeling. Tire Temperature: Excessively high tire temperatures can also easily lead to tire peeling. In more severe cases, it may even cause a blowout.
19
5
Share

Can Motorcycle Antifreeze Be Mixed?

Motorcycle antifreeze cannot be mixed; you must use the same brand of antifreeze. Different brands of antifreeze have varying production formulas, and if mixed, the multiple additives may undergo chemical reactions, rendering the additives ineffective. Method for replacing antifreeze: Drain the old antifreeze, then flush the fluid channels with clean water. Add water to the antifreeze reservoir, then continue adding water to the reservoir so that it continuously flows through the engine cooling system. Start the engine and let it idle for 3 to 5 minutes to circulate the water. Initially, the water flowing out of the reservoir will have a faint pink tint. Continue adding clean water until the water flowing out is clear. Note: Do not forget to disconnect the heater hose and drain the water from the heater core. After draining for about an hour, add the new antifreeze through the radiator hose, which allows the antifreeze to flow quickly into the radiator. Then, add another container of antifreeze to the antifreeze reservoir until it is nearly full. Start the engine and let it run for about 10 minutes. At this point, as some air is expelled from the cooling system, the fluid level will drop slightly. Add more antifreeze until it reaches the maximum mark "MAXT" on the reservoir.
13
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.